The Remote Control - Lexicon DC-1 - REV 1 Owner's Manual

DC-1 Digital Controller
1. OFF and ON
Separate OFF and ON but-
tons are provided for learning
remotes, so that an auto-
mated key sequence does
not require information re-
garding the current on/off sta-
tus of the unit. OFF puts the
unit into standby with audio
muted, video blanked, the
LCD and all LEDs, except for
IR activity, turned off. The IR
LED remains illuminated and
the IR receiver remains ac-
tive. The selected input,
record status, current effect,
volume and balance settings,
and bypass state are saved.
ON umutes audio and re-
stores the unit to the state it
was in prior to standby.
2. EFFECT Up and Down
Display the current effect,
then step through all avail-
able effects. In standby,
pressing either button turns
the unit on, puts it into its last
known state, and loads the
last effect used.
3. BYPASS
Puts the front left and right
outputs into stereo bypass.
The stereo analog or digital
inputs are fed unprocessed
to the front left/right amplifier
outputs while all other ampli-
fier outputs are muted. A front
panel LED will light yellow
and screen messages indi-
cate bypass is engaged.
4. MUTE
Attenuates all audio outputs
except for RECORD or ZONE
2, lights a red LED, and dis-
plays a screen message. At-
tenuation level can be set in
the Setup menu. In standby,
turns the unit on and puts it
into its last known state.
5. VOLUME Up and Down
Display the current volume
setting, then adjust all out-
puts, except RECORD and
ZONE 2. Screen displays
show a volume bar and level
in dB. In standby, pressing
either button turns the unit on
and puts it into its last known
state.
6. BALANCE Front/Rear
and Left/Right
Display, then adjust the Front/
Rear and Left/Right level bal-
ances. Front and Rear con-
trols change the level bal-
ance between the front (Left,
Center, Right) and rear (L&R
Side, L&R Rear) outputs.

The Remote Control

Left and Right controls
change the level balance be-
tween the left and right Front,
Side and Rear outputs. In
standby, pressing any BAL-
ANCE button restores opera-
tion.
7. Input Selection
Individual buttons select from
8 inputs and activate a corre-
sponding green LED on the
front panel. Depending on the
Setup configuration, selection
may also load a new effect. In
standby, pressing any Input
Selection button turns the unit
on, selects the source and
loads the assigned effect, or
restores the last known state.
Installation and
Calibration
8. RECORD/ZONE 2
Selects and deselects the
current input source for
RECORD and ZONE2 out-
puts. When the REC/ZONE 2
function is engaged, red LEDs
are lit at the front panel REC/
ZONE2 button and at the se-
lected source input button.
To modify the ZONE 2 output
without affecting other output
levels, press and hold
RECORD/ZONE2 while ad-
justing VOLUME.
Press MUTE while holding
down RECORD/ZONE2 to
fully attenuate the ZONE2
outputs. The ZONE2 mute
status will be indicated by a
screen message. The attenu-
ation level of the ZONE2 out-
put mute is not user adjust-
able. Repeat to cancel MUTE.
9. MENU:
SELECT, , and DONE
Allow access to and adjust-
ment of all displayed menu
items. (Volume, Bypass, Bal-
ance and Mute functions re-
main activein menu mode.)
MENU and step a dis-
play cursor through listed
menu items. SELECT dis-
plays submenus, or chooses
a menu item for adjustment.
The and buttons alter
the settings of selected pa-
rameters. DONE saves the
current changes.
Press one of the EFFECT
buttons, any Input Selector,
RECORD/ZONE2, or any
BALANCE button to exit.
Press OFF to exit the menu
and enter standby.
10. ACCY
Provides accessory functions
when pressed in conjunction
with other remote buttons.
(See following page.)
9