Memory Groups; Memory Group Assignment; Choosing The Desired Memory Group - Yaesu FT-950 Operating Manual

Memory channels may be grouped into as many as six convenient batches, for easy identification and selection. For ex-
ample, you might want to designate memory groups for AM BC stations, shortwave broadcast stations, contest frequencies,
repeater frequencies and PMS limits, or any other groupings you like.
Each memory group is capable of holding up to 20 memory channels (except Memory Group 01: it is 19 memory channels,
and the Group size is fixed). When a memory channel is grouped, the channel numbers change to correspond to the chart
below:

Memory Group Assignment

1. Press the [ MENU ] button to enter the Menu mode.
2. Rotate the [ SELECT ] knob to select Menu item "029
GENE MEM GRP GENE MEM GRP
GENE MEM GRP GENE MEM GRP GENE MEM GRP".
A :
DVICE
Press the [ SELECT ] knob momentarily to toggle the
Menu item display between "029 GENE
GRP GRP GRP GRP". GRP
3. Rotate the [ CLAR/VFO-B ] knob to set this Menu item
to "On On" (the default setting is "OFF
On On On
4. Press and hold in the [ MENU ] button for one second
to save the new setting and exit. Operation will now be
restricted to the six Memory Groups.
To cancel Memory Group operation, repeat steps (1)
through (4) above, choosing "OFF
A :
DVICE
To avoid confusion, note that the PMS memory group and
the PMS memories "P1L" through "P9U" will be so des-
ignated.

Choosing the Desired Memory Group

You may recall memories just within a particular Memory Group, if desired.
1. Press the [ V/M ] button, if necessary, to enter the
"Memory" mode.
A :
DVICE
If you can not enter the "Memory" mode, check to see
if the transceiver is in VFO-B mode (the green [ VFO-
B ( RX )] Indicator/Switch is illuminated). If so, press
the [ VFO-A ( RX )] Indicator/Switch to return operation
to VFO-A. Now, press the [ V/M ] button to enter the
"Memory" mode.
2. Press the [ GRP ] button (located to the upper right of
the [ CLAR/VFO-B ] knob). The imbedded LED in-
side the switch will glow orange.
3. Rotate the [ CLAR/VFO-B ] knob to select the desired
Memory Group.
4. Press the [ MCH ] button (just below the [ GRP ] but-
ton). The imbedded LED inside the switch will glow
orange.
5. Rotate the [ CLAR/VFO-B ] knob to select the desired
Memory Channel within the Selected Memory Group.
A :
DVICE
If no channels have been assigned to a particular Memory
Group, you will not have access to that Group.
FT-950 O
PERATING
M
EMORY
029 029 029
029
029 GENE" and "MEM
029 GENE 029 GENE 029 GENE MEM MEM MEM MEM
OFF"). OFF OFF OFF
OFF" in step (3).
OFF OFF OFF
M
ANUAL
M
EMORY
G
ROUPS
[ SELECT ] Knob
[ MENU ] Button
M
EMORY
G M "OFF"
ROUP EMORY
01 ~ 19
20 ~ 39
40 ~ 59
60 ~ 79
80 ~ 99
P-1L/1U ~ P-9L/9U
US1 ~ US5
[ VFO-A ( RX )] Button
O
PERATION
[ CLAR/VFO-B ] Knob
C N
HANNEL UMBER
G M "ON"
ROUP EMORY
1-01 ~ 1-19
2-01 ~ 2-20
3-01 ~ 3-20
4-01 ~ 4-20
5-01 ~ 5-20
P-1L/1U ~ P-9L/9U
US-1 ~ US-5
[ VFO-B ( RX )] Button
[ GRP ] Button
[ V/M ] Button [ MCH ] Button
[ CLAR/VFO-B ] Knob
Page 95