Tuning Group; Tx Audio Group; Tun Dialstp; Tun Cw Fine - Yaesu FT-950 Operating Manual

M M
ENU ODE
TUNING G

084 TUN DIALSTP

Function: Setting of the Main Tuning Dial knob's and the
[ CLAR/VFO-B ] knob's tuning speed on the SSB, CW,
and AM modes.
Available Values: 1/5/10 Hz
Default Setting: 10 Hz

085 TUN CW FINE

Function: Enabling/disabling of the "Fine" tuning speed
in the CW mode.
Available Values: EnA/diS (ENABLE/DISABLE)
Default Setting: diS (DISABLE)
EnA (ENABLE): Tuning in 1 Hz steps on the CW mode.
diS (DISABLE): Tuning according to the steps deter-
mined via menu item "084 TUN
DIALSTP DIALSTP
DIALSTP DIALSTP DIALSTP".

086 TUN MHz SEL

Function: Selects the tuning steps for the [ CLAR/VFO-
B ] knob when the [ MHz ] button is pressed.
Available Values: 1/0.1 MHz
Default Setting: 1 MHz

087 TUN AM STEP

Function: Selects the tuning steps for the microphone's
[ UP ] / [ DWN ] keys in the AM mode.
Available Values: 2.5/5/9/10/12.5 kHz
Default Setting: 5 kHz

088 TUN FM STEP

Function: Selects the tuning steps for the microphone's
[ UP ] / [ DWN ] keys in the FM mode.
Available Values: 5/6.25/10/12.5/20/25 kHz
Default Setting: 5 kHz

089 TUN FM DIAL

Function: Setting of the Main Tuning Dial knob's and the
[ CLAR/VFO-B ] knob's tuning speed in the FM mode.
Available Values: 10/100 Hz
Default Setting: 100 Hz

090 TUN MY BAND

Function: Programs a band to be skipped while selecting
bands using the [ CLAR/VFO-B ] knob.
To program the band to be skipped, rotate the [ CLAR/
VFO-B ] knob to recall the band to be skipped while se-
lecting bands via the [ CLAR/VFO-B ] knob, then press
the [ ENT ] button to change this setting to "ON" (a "d d d d d "
notation will replace the "E E E E E " notation). Repeat the same
procedure to cancel the setting (skipped "Off": "d d d d d " nota-
tion appears).
Page 116
ROUP
084 TUN 084 TUN
084 TUN 084 TUN
TX AUDIO G
091 TAUD EQ1 FRQ
Function: Selects the center frequency of the lower range
for the parametric microphone equalizer.
Available Values: OFF/100 ~ 700 Hz (100 Hz/step)
Default Setting: OFF
OFF: The equalizer gain and Q-factor are set to fac-
tory defaults (flat).
100 ~ 700: Center frequencies of 100 Hz ~ 700 Hz.
You may adjust the equalizer gain and Q-factor at this se-
lected audio frequency via menu items "092 TAUD EQ1
LVL" and "093 TAUD EQ1 BW
LVL LVL LVL LVL 093 TAUD EQ1 BW 093 TAUD EQ1 BW". 093 TAUD EQ1 BW 093 TAUD EQ1 BW
092 TAUD EQ1 LVL
Function: Adjusts the equalizer gain of the low range of
the parametric microphone equalizer.
Available Values: –10 ~ +10
Default Setting: +5
093 TAUD EQ1 BW
Function: Adjusts the Q-factor of the low range of the
parametric microphone equalizer.
Available Values: 1 ~ 10
Default Setting: 10
094 TAUD EQ2 FRQ
Function: Selects the center frequency of the middle range
for the parametric microphone equalizer.
Available Values: OFF/700 ~ 1500 Hz (100 Hz/step)
Default Setting: OFF
OFF: The equalizer gain and Q-factor are set to fac-
tory defaults (flat).
700 ~ 1500: Center frequencies of 700 Hz ~ 1500 Hz.
You may adjust the equalizer gain and Q-factor at this se-
lected audio frequency via menu items "095 TAUD EQ2
LVL" and "096 TAUD EQ2 BW
LVL LVL 096 TAUD EQ2 BW 096 TAUD EQ2 BW
LVL LVL 096 TAUD EQ2 BW". 096 TAUD EQ2 BW
095 TAUD EQ2 LVL
Function: Adjusts the equalizer gain of the middle range
of the parametric microphone equalizer.
Available Values: –10 ~ +10
Default Setting: +5
096 TAUD EQ2 BW
Function: Adjusts the Q-factor of the middle range of the
parametric microphone equalizer.
Available Values: 1 ~ 10
Default Setting: 10
FT-950 O
ROUP
092 TAUD EQ1 092 TAUD EQ1 092 TAUD EQ1 092 TAUD EQ1
095 TAUD EQ2 095 TAUD EQ2
095 TAUD EQ2 095 TAUD EQ2
M
PERATING ANUAL