Advertisement
Quick Links
®
iBoard
by APS
READ INSTRUCTIONS CAREFULLY BEFORE START ING
INSTALLATION. REMOVE CONTENTS FROM BOX AND
VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS
RECOMMENDED.
*ROCKER PANEL MOUNT
*NO DRILLING REQUIRED/CUTTING MAYBE REQUIRED
PART LIST
Driver Side Step Bar
iBoard
1#
1#
1#
1#
Customer Support: info@iboardauto.com
Fastener Size
Tightening Torque (ft-lbs)
6mm
8mm
10mm
12mm
14mm
Front
1
®
PART#: IB-071C&H
Required
6-7
16-18
31-32
56-58
92-94
Passenger Side Step Bar
2#
1#
1#
1#
Rev. 20240401
X
√
X
X
X
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for APS iBoard IB-071C
Summary of Contents for APS iBoard IB-071C
- Page 1 ® ® iBoard by APS PART#: IB-071C&H Fastener Size Tightening Torque (ft-lbs) Required READ INSTRUCTIONS CAREFULLY BEFORE START ING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS 16-18 √ RECOMMENDED. 10mm 31-32 12mm 56-58...
- Page 2 iBoard ® Mounting Bracket List Item Description Item Description Mounting Brackets Passenger Front Mounting Bracket Hardware Package A (For Bracket Installation) Item Description Item Description M8X1.25-25mm Hex Bolts M8 Lock Washers M8 Large Flat Washers M8 Clip Nuts Hardware Package B (For Stainless Steel Step Bar Installation) Item Description Item...
- Page 3 iBoard ® STEP 1 Factory 8mm Threaded Start the installation under the driver side of the vehicle. Locate Insert In Body Panel the 4 tabs along the bottom edge of the body, (pinch weld). Mounting Brackets will bolt to the 1st, 2nd, 3rd, and 4th mount- ing tabs, (Fig 1).
- Page 4 iBoard ® Note: The Sliders are packed with the Step Bars. STEP 3 Level and adjust the Step Bar and fully tighten all hardware. Select (1) Mounting Bracket, bolt the Mounting Bracket to the installed M8 Clip Nuts and/or the factory threaded holes on Driver Side Front Mounting Location with (2) M8 X1.25-25mm STEP 6 Hex Bolts, (2) M8 Lock Washers and (2) M8 Large Flat Wash-...
- Page 5 iBoard ® Slider (2) Carriage Bolts Slider with (2) Carriage Bolts Step Bar (Bottom View) (Fig 7) Slider Installation Mounting Bracket Step Bar Slider (w/ installed (2) M8 Large Flat Washers Carriage Bolts) (2) M8 Nylon Lock Nuts (Fig 8) Step Bar Installation Remove (4) Hex Bolts To Remove Plastic Cover Remove (3) Hex Bolts...
- Page 6 iBoard ® Front Models With 8mm Threaded Insert In Body Panel: (1) M8 x1.25-25mm Hex Bolt (1) M8 Lock Washer (1) M8 Large Flat Washer Remove (2) Factory Bolts To Remove Tank Straps (Fig 11) 07-16 Passenger Side DEF Tank And Cover Models With Weld Nut On Pitch Weld: STEP 7 (1) M8 x1.25-25mm Hex Bolt...
- Page 7 iBoard ® STEP 9 Mark Pictured Is Approximately Repeat Step 5 to install the passenger side Step Bar. 70mm X 10mm STEP 10 Once the Step Bars are installed and all hardware fully tight- ened, reinstall the DEF tank and cover, if equipped, as de- scribed in Step 6.
Need help?
Do you have a question about the iBoard IB-071C and is the answer not in the manual?
Questions and answers