Advertisement
Quick Links
•
Buick LaCrosse 2017-2018
Buick Regal 2018
•
•
Cadillac ATS 2015-2018
Cadillac CT6 2015-2018
•
•
Cadillac CTS 2015-2018
•
Cadillac ELR 2015-2018
•
Cadillac XT5 2015-2018
Cadillac XTS 2015-2018
•
•
Cadillac Escalade 2015-2017
Please read thoroughly before starting installation and check that kit contents are complete.
Items Included in the Kit:
Wireless Charging Module
4 Spacers
4 7x3/4" screws
These instructions
NOTE: We strive to provide accurate and up-to-date installation instructions. For the latest full color
instructions, as well as an installation video, please visit www.brandmotion.com
Safety Precautions:
• Work in well ventilated area that is clear of obstructions.
• Secure vehicle with tire chucks in both front and rear of tires.
• Turn vehicle accessories OFF and ensure ignition key is in OFF position.
• Wear safety goggles and snug fitting clothes.
• Use tools only for their intended purpose and which are in good repair.
• Only perform this task if confidence, skill, and physical ability permit.
FDMC-1285 Instructions.docx
GM Wireless Charger Retrofit
(Kit # FDMC-1285)
•
Cadillac Models 2015-2017
Chevy Bolt EV 2015-2017
•
•
Chevy Suburban 2015-2017
Chevy Tahoe 2015-2017
•
•
Chevy Volt 2015-2017
•
Chevy Camaro 2016-2018
•
Chevy Impala 2016-2018
Chevy Malibu 2016-2018
•
•
Chevy Colorado 2015-2018
Page 1 of 10
INSTALLATION INSTRUCTIONS
Tools & Supplies Needed:
Plastic panel removal tools
T-20 Torx
Phillips Screwdriver
•
Chevy Cruze 2015-2018
Chevy Equinox 2018
•
•
Chevy Silverado 2016-2017
GMC Canyon 2015-2018
•
•
GMC Sierra 2016-2017
•
GMC Yukon 2015-2017
•
GMC Models 2015-2017
Advertisement
Related Manuals for BrandMotion FDMC-1285
Summary of Contents for BrandMotion FDMC-1285
- Page 1 These instructions NOTE: We strive to provide accurate and up-to-date installation instructions. For the latest full color instructions, as well as an installation video, please visit www.brandmotion.com Safety Precautions: • Work in well ventilated area that is clear of obstructions.
- Page 2 4. STOP. Test charger prior to full installation. To accomplish this, connect new power adapter. Set Qi- compatible wireless charging phone directly on charger. Turn key to on position. Phone should begin to charge. Remove power adapter and continue with installation. Page 2 of 10 FDMC-1285 Instructions.docx...
- Page 3 7. Test device by putting key in the on position and placing phone on charging mat. Phone should start to charge. Note: Larger phones may require additional adjustments. Please see next page for adjustment steps. Page 3 of 10 FDMC-1285 Instructions.docx...
- Page 4 1. If you have followed all of the previous steps and your phone will not charge, you will be required to flip your factory charging mat. You can accomplish this by removing the snap panel once more. 2. Remove the Brandmotion coil by removing the 4 screws and spacers. Unhook power connection and set module to the side.
- Page 5 2016 Camaro Page 5 of 10 FDMC-1285 Instructions.docx...
- Page 6 0, Wireless Charging System Module Bracket Bolt (2) » Remove [2x] 1, Disconnect the electrical connector. 2, Wireless Charging System Module Bracket (3) » Remove 3, Wireless Charging System Module Bracket Bolt (1) » Remove [4x] Page 6 of 10 FDMC-1285 Instructions.docx...
- Page 7 15-18 Cadillac CT6 Page 7 of 10 FDMC-1285 Instructions.docx...
- Page 8 2018 LaCrosse 2017 LaCrosse 2017-2018 Cruze Page 8 of 10 FDMC-1285 Instructions.docx...
- Page 9 2018 Impala, Malibu Page 9 of 10 FDMC-1285 Instructions.docx...
- Page 10 2016 Volt Page 10 of 10 FDMC-1285 Instructions.docx...
Need help?
Do you have a question about the FDMC-1285 and is the answer not in the manual?
Questions and answers