Advertisement
Table of Contents
Rear Vision System – Aftermarket and Factory 8.4" Touch Screen Display
(Factory Display requires Chrysler/Dodge dealer to activate)
2013 – Current Dodge Ram (Kit part number 1009-6503)
NOTE: Raising Reverse signal voltage using a Single Pull Dual Throw Relay is required when used with aftermarket
mirrors and displays. (Please refer to detailed installation steps on Page 7 of these instructions.)
Items Included in the Kit:
Chassis Harness with RCA*
Tailgate Handle with Camera
8.4" Factory Touch Screen Jumper
Harness
1 bag containing:
Plug for Non-Locking Tailgates
Red wire with terminal for older vehicles (optional)
Black wire with terminal for older vehicles (optional)
1 bag containing:
These instructions
Template
*In some cases a RCA extension may be required
to connect to your aftermarket display; Kit#
9002-6111 may be purchased from
Brandmotion.com
Install Tailgate Handle Camera
1. Set up a work area on which to set the tailgate after
removal. This area should be well protected to avoid
damage to tailgate.
2. Use your fingers to remove the black plastic filler
panel at rear of pickup bed adjacent to the license
plate. Press on the end tab and lifting outward.
Next, slide the red tab from the locked position and
unplug the tailgate power lock harness connector.
6503 Instructions 2-4-14.Doc
Please read thoroughly before starting installation
and check that kit contents are complete.
(Optional)
We strive to provide accurate and up-to-date installation instructions.
For the latest full color instructions, please visit www.brandmotion.com
INSTALLATION
I NSTRUCTIONS
Tools Required:
Socket Wrench with 7mm & 8mm Sockets
T20 and T30 Torx Bits
Phillips and Flat Blade Screwdrivers
Power Drill
1/8" Drill Bit
1" Hole Cutter
Pushpin Removal Tool
Round File or Deburring Tool
Center Punch
Utility Knife or Side Cutters
Masking Tape
Corrosion Inhibitor (recommended)
Soldering Iron & Solder (recommended)
Wire Ties (recommended)
3. Unhook both tailgate support straps by inserting a
Flat Blade Screwdriver between the locking tab and
strap mount. Lift the locking tab away from the
strap mount with the screwdriver while sliding the
tailgate strap upwards. The tailgate strap hanger
can now be removed from the mount.
4. Open tailgate about ten degrees and lift right side of
the tailgate off the pin. Next, slide tailgate to the
right to remove taking care not to damage the paint.
NOTE: Tailgate removal and installation requires two
people.
Page 1 of 8
Advertisement
Table of Contents
Related Manuals for BrandMotion 1009-6503
Summary of Contents for BrandMotion 1009-6503
- Page 1 Rear Vision System – Aftermarket and Factory 8.4” Touch Screen Display (Factory Display requires Chrysler/Dodge dealer to activate) 2013 – Current Dodge Ram (Kit part number 1009-6503) NOTE: Raising Reverse signal voltage using a Single Pull Dual Throw Relay is required when used with aftermarket mirrors and displays.
- Page 2 INSTALLATION I NSTRUCTIONS 5. Remove the handle access panel inside the tailgate using a T30 Torx driver. (NOTE: If vehicle is equipped with a bed liner, the tailgate portion of the liner must be removed prior to this step.) 9.
- Page 3 INSTALLATION I NSTRUCTIONS 17. RECOMMENDED: Use a Cotton Swab or small brush 12. Route the supplied Camera Harness through the to apply Corrosion Inhibitor to exposed edges. pass-through hole in the inner brace of the tailgate. 18. Taking care not to damage the Camera Harness, 13.
- Page 4 INSTALLATION I NSTRUCTIONS 26. Insert the large gray connector end of the supplied Chassis Harness through the body floor plug hole. 23. Remove rear driver’s-side sill plate by lifting it at front and working your way back with your hands. 27.
- Page 5 INSTALLATION I NSTRUCTIONS Connect Chassis Harness to Vehicle Wiring 30. Route Chassis Harness around B-pillar trim by lifting 36. Connect the supplied Chassis Harness Red, Green, up on the trim and feeding harness through to front. and Black leads as directed in the chart appropriate for your vehicle below.
- Page 6 INSTALLATION I NSTRUCTIONS Figure 4 Chart B: 2013 to present Ram Aftermarket mirror/ display / Splice Circuit 86 Relay wire to Reverse (+) Aftermarket NAV signal at white/tan wire in Pin 41. Using a commonly available Single Pull Dual Throw Relay (Figure 3), splice the leads of the supplied Mirror Harness to each numbered circuit of the female relay connector as follows...
- Page 7 !"#$%&&%$!'"(!"#$)*+$!'"#( If using this kit with the factory 8.4” touch screen, follow Steps 39 through 53 and Steps 56 through 58 below. If using this kit with an aftermarket mirror / display / NAV display, connect Chassis Harness male RCA to “Camera IN” on the aftermarket mirror / display/ NAV display.
- Page 8 INSTALLATION I NSTRUCTIONS 57. Start vehicle and shift into Reverse in order to check 55. Reassemble all previously removed parts. that all connections were made properly. If all of the connections are correct you will see the camera If you connected the camera to a factory 8.4”...
Need help?
Do you have a question about the 1009-6503 and is the answer not in the manual?
Questions and answers