Powtran PI150 Series Operation Manual
Powtran PI150 Series Operation Manual

Powtran PI150 Series Operation Manual

Frequency inverter

Advertisement

PI150 series frequency inverter operation manual
1.Foreword
Thank you for choosing Powtran PI150 series fundamental form frequency inverter.
The diagrams of these operating instructions are used for convenience of explanation and may be slightly
different from the product due to product upgrades. Please refer to the actual product.
Please take this manual to the end user and keep it for future maintenance use.
If you have any questions, please get in touch with our company or our agent in time, we will offer dedicated
service to you.
2.Instructions on nameplate
Production Sequence Number
Model designation:
POWTRAN Inverter
Series code
PI150 series
Rated output capacity
2R2 : 2.2kW
004 : 4kW
3.Dimension
0.75 to 5.5kW G3 dimension
Model
PI150 0R4G1(Z)
PI150 0R4G2(Z)
PI150 0R7G1(Z)
PI150 0R7G2(Z)
PI150 0R7G3(Z)
PI150 1R5G1(Z)
PI150 1R5G2(Z)
PI150 1R5G3(Z)
PI150 2R2G3(Z)
PI150 2R2G3(Z)
PI150 2R2G1(Z)
PI150 2R2G2(Z)
PI150 004G3(Z)
PI150 5R5G3(Z)
4.Operation keyboard introduction
4.1 Keyboard indicator
Inverter Model
Output Power Spec
Input Source Spec
Output Spe
Bar Code
Production Address
PI 150
0.75 to 5.5kW G3 support rail mounting
Dimension (mm)
Output
power (kW)
L
0.4
0.4
0.75
0.75
0.75
138
1.5
1.5
1.5
2.2
2.2
2.2
2.2
185
4
5.5
Figure 4-1:Operation panel display
MODEL
PI150 2R2G3
POWER
2.2kW
INPUT
AC 3PH 380V(-15%)
OUPUT
AC 3PH 0V
DALIAN POWTRAN TECHNOLOGY CO.,LTD.
2R2 G 3
Output configuration
0: Without brake unit as standard (Omitted)
Z: With brake unit (Optional)
Input Voltage Level
1:Single-phase 220V
2:Three-phase 220V
3:Three-phase 380V
Standard load
H
Installation
(mm)
W
H
A
B
72 123.5 127
61
72
134
175
45
1 / 15
440V(+10%) 50Hz/60Hz
400Hz
Vin
5.1A
0
ZPB1A88888888
d
A
B
W
Guide rail installation
position (mm)
d
E
5
62
5
82
E
L
Weight(kg)
1.1
1.3

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PI150 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Powtran PI150 Series

  • Page 1 PI150 series frequency inverter operation manual 1.Foreword Thank you for choosing Powtran PI150 series fundamental form frequency inverter. The diagrams of these operating instructions are used for convenience of explanation and may be slightly different from the product due to product upgrades. Please refer to the actual product.
  • Page 2: Standard Specifications

    Indicator light Name Running indicator light * ON: The inverter is working * OFF: The inverter stops Forward/reverse running light Status FWD/REV * ON: In forward status light * OFF: In reversal status Frequency indicator Current indicator 4.2 Operation panel button description Sign Name Function...
  • Page 3: Wiring Diagram

    7. Parameter List In PI150 series frequency inverters ,some parameters are "manufacturer reserved", and their serial numbers are not listed in the function parameter table,which leads to the discontinuity of some parameter serial numbers in the table. For the parameters not introduced in the manual, please do not attempt to modify them to avoid causing errors.
  • Page 4 d0.05 Output power Calculated value for motor output power 0.1kW d0.06 Output torque Motor output torque percentage 0.1% d0.07 DI input status DI input status d0.08 DO output status DO output status d0.09 AI1 voltage AI1 input voltage value 0.01V d0.12 Count value Actual pulse count value in counting function...
  • Page 5 Depends on ☆ F0.18 Carrier Frequency 0.5kHz to 16.0kHz models Maximum output ★ F0.19 50.00Hz to 320.00Hz 50.00Hz frequency Upper limit frequency 0:F0.21setting; 1:Analog AI1 setting; ★ F0.20 source 5: Communications reference F0.23 (Lower limit frequency) to F0.19 (Maximum ☆ F0.21 Upper limit frequency 50.00Hz...
  • Page 6 vice versa. When the terminal is active, the PID integral adjustment function is PID integral pause paused, but the proportion and differential adjustments of PID are still valid. Switch between frequency source When the terminal is active, the frequency source A is replaced by the master setting and preset frequency (F0.01) preset frequency...
  • Page 7 When the count reaches the set value of E0.08, output ON signal. Setup counter arrive Specifies the count value reaches. Specifies the count When the count reaches the set value of E0.09, output ON signal. value reaches Counting Function Reference E0 group. When the actual length of the detection of more than E0.05 set length, Length arrival output ON signal.
  • Page 8 ☆ F3.10 Braking current 0% to 100% ☆ F3.11 Braking time 0.0s to 100.0s 0.0s ☆ F3.12 Braking utilization rate 0% to 100% 100% 0:Linear acceleration and deceleration; ★ F3.13 Ac/deceleration mode 1:S curve acceleration and deceleration A 2:S curve acceleration and deceleration B ★...
  • Page 9 Single digit: CRC mistake selection: 0: Reply verification error; 1: No reply on verification error; Communication read and write ☆ F6.13 Ten digit: Broadcast message screening selection: 0-no data selection screening; 1-screening Hundred digit: Inverter fault information read selection: 0-read; 1-no read ☆...
  • Page 10 ☆ F7.47 Awaken delay time 0.0s t0 6500.0s 0.0s 0.00Hz ☆ F7.48 Dormancy frequency 0.00Hz t0 awaken frequency (F7.46) ☆ F7.49 Dormancy delay time 0.0s t0 6500.0s 0.0s AI1 input voltage protection lower ☆ F7.50 0.00V t0 F7.51 3.1V limit AI1 input voltage protection upper ☆...
  • Page 11 ☆ E0.09 Specified count value 1 t0 65535 1000 Multi-speed, sample PLC parameter Factory Code Parameter name Setting range setting ☆ E1.00 0 stage speed setting 0X -100.0% t0 100.0% 0.0% ☆ E1.01 1 stage speed setting 1X -100.0% t0 100.0% 0.0% ☆...
  • Page 12 ☆ E2.04 PIDsetting feedback range 0 t0 65535 1000 ☆ E2.05 PIDinversion cutoff frequency 0.00 t0 F0.19(Maximum frequency) 0.00Hz ☆ E2.06 PIDdeviation limit 0.0% t0 100.0% 2.0% ☆ E2.07 PIDdifferential limiting 0.00% t0 100.00% 0.10% ☆ E2.08 PIDreference change time 0.00s t0 650.00s 0.00s ☆...
  • Page 13: Fault Alarm And Countermeasures

    Hundreds digit:b group display selection(The same above) Thousands digit:y group display selection(The same above) Tens thousands digit:L group display selection(The same above) Units digit:Reserved Personality parameter Tens digit :User’s change parameter display selection ☆ y0.03 group display selection 0:Not display 1:Display Function code 0: Modifiable ☆...
  • Page 14 1.The acceleration time is too short 1.Increase acceleration time 2.Manual torque boost or V/F curve is 2.Adjust manual torque boost or not suitable V/F curve 3.The voltage is low 3.Set the voltage to the normal range 4.The short-circuit or earthing of 4.Eliminate peripheral faults inverter output happens Acceleration...
  • Page 15 running time initialization function parameters arrival fault Input custom fault 1 signal through the Err.27 Custom fault 1 Reset run multi-function terminal DI Input custom fault 2 signal through the Err.28 Custom fault 2 Reset run multi-function terminal DI Total power-on Total power-on time reaches the set Clear history information by using Err.29...

This manual is also suitable for:

Pi150 2r2g3Pi150 0r4g1Pi150 0r4g2Pi150 0r7g1Pi150 0r7g2Pi150 0r7g3 ... Show all

Table of Contents