Subscribe to Our Youtube Channel
Related Manuals for Amphenol PowerLok G3
Summary of Contents for Amphenol PowerLok G3
- Page 1 Manual P/N：8P1248 Rev.00 20240308 PowerLok G3 接头通用安装说明 PowerLok G3 connector General Installation Instructions www.amphenol-gec.com...
- Page 2 PowerLok G3 接头通用安装说明 PowerLok G3 connector General Installation Instructions G3 插座安装说明 Receptacle G3 Installation Instructions 插座安装面板要求 Receptacle Install Panel Requirements 1 面板厚度不超过12mm。 1 Thickness of panel should not exceed 12mm。 2 面板与插座接触区域应符合以下要求: 2 The contact area between panel and receptacle shall meet the following requirements: 2-1 表面粗糙度应为6.3或更好。...
- Page 3 PowerLok G3 接头通用安装说明 PowerLok G3 connector General Installation Instructions 安装步骤 Installation Steps 1 根据下表一，选择对应安装扭力 Apply proper torque according to table.1 below. 安装扭力参数表 Install Torsion Data Table1 螺丝规格 使用场景 装配扭力（N·m） Screw Standard Assembly Place Install Torque 面板 1.6~2.4N.m Panel 铜排 3.6~4.4N.m Terminal 铜排...
- Page 4 PowerLok G3 接头通用安装说明 PowerLok G3 connector General Installation Instructions 4 然后将插座用M4螺丝固定在安装面板上，平垫圈尺寸需符合 ISO7092 要求。 Then fix the receptacle on the mounting panel with M4 screws, and the plain washers size must meet ISO7092 requirements. 平垫圈最大尺寸 螺丝规格 Dimensions of plain Screw SPEC washers (max mm) 5 端子上螺丝按以下步骤参照处理...
- Page 5 PowerLok G3 接头通用安装说明 PowerLok G3 connector General Installation Instructions 5-4 完成安装后检查胶料无破损，PIN针无弯曲变形 5-4 Check product after Complete installation, Any damage on plastic is not allowed, any deformation on Pin is not allowed. 20240308_ Rev.00 Document No: 8P1248 04/09...
- Page 6 PowerLok G3 接头通用安装说明 PowerLok G3 connector General Installation Instructions 6：在线缆组装好后需要做绝缘电阻和耐压测试，建议客户参考下面的测试参数 Need to do the Insulation Resistance and DWV test after cable assembly. It is recommended that the customer refer to the following test parameters 6-1 绝缘电阻测试 6-1 Insulation Resistance Positions Test voltage/time 测试时间（推荐）...
- Page 7 PowerLok G3 接头通用安装说明 PowerLok G3 connector General Installation Instructions G3 插头安装说明 G3 Plug Installation Instructions 安装步骤 Installation Steps 1 选择与插座键位对应的插头线束组件，注意插头锁扣颜色与插座防触Pin颜色对应如下图。 1 Select the plug harness assembly corresponding to the receptacle, and note that the color of the plug latch corresponds to the color of the receptacle anti-touch Pin as shown below.
- Page 8 PowerLok G3 接头通用安装说明 PowerLok G3 connector General Installation Instructions 4 将CPA水平后推到底如图示，完成安装。 4 Push the CPA down as shown in the figure to complete the installation. 插头拔出指引 Pulling Out Plug From Receptacle Guideline 1 如图示将CPA推到底，松开CPA。 1 Push the CPA to the bottom as shown in the figure to release the CPA.
- Page 9 PowerLok G3 接头通用安装说明 PowerLok G3 connector General Installation Instructions 插头线束固定 Plug harness secure 1 线束的最小弯曲半径R≥线材外径*10。 1 The minimum bending radius of the wire harness R≥ the outer diameter of the cabled *10. 2 在接头尾部100mm处需将线材固定。 2 Secure the cable 100mm from the end of the connector.
- Page 10 PowerLok G3 接头通用安装说明 PowerLok G3 connector General Installation Instructions 版本记录 Revision history 序号 版本 变更内容 日期 Number Content of change Date 新出 2024/03/08 New Release 20240308_ Rev.00 Document No: 8P1248 09/09...
- Page 11 Specifications are subject to change without notice. Contact your nearest Amphenol Corporation Sales Office for the latest specifications. All statements, information and data given herein are believed to be accurate and reliable but are presented without guarantee, warranty, or responsibility of any kind, expressed or implied.
Need help?
Do you have a question about the PowerLok G3 and is the answer not in the manual?
Questions and answers