Savant FTC-P100 Quick Reference Manual

The Savant Fiber Transmitter and Room Controller (FTC-P100) Quick Reference Guide
provides the information necessary to install the FTC-P100 and associated components.
Important: To confirm this document is the latest version, refer to
http://www.SavantSystems.com/ > Dealer Login > Knowledge Base > Products.
Box Contents
(1) Fiber Transmitter and Room Controller (FTC-P100-xx)
(1) Installation Kit (075-0125-xx)
• (2) Conn 3 Pin SCR for GPIO and Relay ports (028-9351-xx)
• (2) Conn 6 Pin SCR for IR ports (028-9352-xx)
• (4) Screw M3 X 8MM Flat Phil Blk (039-0017-xx)
• (2) Side Mount Chassis Brackets (071-0628-xx)
(1) Quick Reference Guide (this document)
Optional Accessories
(1) AC Power Cord (064-0079-xx)
(1) Power Supply 12V DC 2.5A (025-0082-xx)
(1) Fiber Cable –1000 ft (CBL-F1000-xx)
(1) Fiber Connectors – 10 pack (CON-F1000-xx)
(1) Fiber Termination Kit – (FTK-F1000-xx)
Specifications
Environmental
Operating Temperature 32º to 104º F (0º to 40º C)
Operating Humidity 5% to 95% Non-condensing
Maximum BTUs 51 BTUs per hour
Cooling 3 cubic feet per minute (CFM) recommended
Physical
Dimensions (W x D x H) 7.10 x 1.65 x 11.72 x in (18.03 x 4.19 x 29.76 cm)
Weight 3.05 lbs (1.38 kg)
Power over Ethernet
Supported Standards IEEE 802.3af
IEEE 802.3at
Optional Power
Nominal Power 10.8W
Maximum Power 14.8W
Power Supply 12V DC – 120-230V AC 50/60 Hz
Regulatory
Safety and Emissions FCC Part 15/CE Mark/C-Tick
RoHS Compliant
Left Side
1 2
&$'$(
012033
1 On/Off button After initial power up, press and hold the On/Off button for
approximately 5 seconds to power down the unit. Press
and hold the On/Off button to power the unit back up.
2 Reset button Press to reset the FTC-P100. * See below to reset factory
default DHCP mode.
3 Power LED Green indicates the system has adequate power and is
operating normally.
Red indicates the system is off. The controller hardware
has 12V DC power, but the board is powered off.
Off indicates that the system is not receiving AC power.
4 Status LED Green indicates the Host has established communications
with the FRC-P100.
Green flashing indicates the FTC-P100 is ready (running
with DHCP IP address), but the Host has not established
communications with the FTC-P100.
Off indicates the embedded processor is resetting or is
booting the embedded firmware.
Red indicates the Host has determined the firmware needs
to be updated, but a problem occurred during the process
that will initiate a reset.
Red flashing indicates the embedded firmware is running,
but has not received a DHCP IP Address.
Amber indicates the Host is currently updating the
embedded firmware.
Copyright © 2012 Savant Systems LLC, SAVANT and RacePoint Blueprint are trademarks of Savant Systems, LLC.
All brand names, product names and trademarks are the property of their respective owners.
Savant Systems, LLC reserves the right to change product specifications without notice.
45 Perseverance Way, Hyannis, MA 02601
060612
Fiber Transmitter & Room Controller
3 4 5 6
!"#$% )(*(+' &),-, .!/0
456$"2 /& &$9*:
758$%
7 8 9
(FTC-P100)
Quick Reference Guide
5 RS232 LED
6 GPIO LED
7 Video/Fiber LED
8 IR LED
9 Relay LED
* To reset the factory default DHCP mode, jumper GPIO pin 1 and IR pin 1+ together and
refer to Restoring System Defaults below.
Right Side
1 2
1 Ethernet PoE port
2 RS232-1, -2 serial
ports
3 GPIO R, COM, 1 port
4 Relay NC/C/NO port
SmartControl 25
5 IR 1- 6 ports
6 Audio In R, L ports
7 VGA port
8 HDMI In 1- 4 ports
9 Fiber Out port
10
11 12V DC
Restoring System Defaults
This procedure will clear a static IP address, which has been set up by the installer using the
embedded scanner, RPMembscanner— a Savant specific program located in the RacePoint
Blueprint™ folder and installed when you load RacePoint Blueprint™ on your computer.
To restore the default state of the FTC-P100, do the following.
Phone 508.683.2500 Fax 508.683.2600
Amber flashing indicates the FTC-P100 has a valid link-
local IP Address and is waiting to connect to the Host.
Green indicates RS-232 serial port data activity.
Off indicates no RS-232 serial port activity.
Green indicates GPIO port signal activity.
Off indicates no GPIO port activity.
Green indicates valid video/fiber link.
Off indicates no fiber link.
Green indicates IR port signal activity.
Off indicates no IR port activity.
Green indicates Relay port signal activity.
Off indicates no Relay port activity.
6 7
3 5
4
RJ-45 10/100Base-T, auto-negotiating port allows
communication between a remote computer and the
embedded CPU at 10/100 data rates.
Green (right) indicates an Ethernet speed of 100 Mb; when
Off indicates an Ethernet speed of 10 Mb.
Green (left) indicates Ethernet data activity.
Power over Ethernet (PoE) is supported on this port.
RJ-45 ports used to transmit and receive serial binary data
transmission.
General Purpose Input and Output port—uses 3-pin screw-
down connector. The digital GPIO ports are binary I/O ports
used for contact closure, trigger (output), or detect (input). R
is reserved (not used). The COM pin is used for common
ground. Pin 1 is used for input or output.
When configured as an input, the port detects a voltage
present (GPIO input). GPIO inputs can safely detect the
presence of a voltage of 0-30V DC with a threshold of
approximately 2.4V DC.
When configured as an output, a GPIO port outputs a
voltage between 0-12V DC. The maximum current per port
is 150 milliamps. An overcurrent condition shuts down the
output until that condition is removed.
This port provides dry contacts (open/closed) to control
devices requiring basic on/off operation. A single relay port
can carry a maximum of 30V DC with a maximum current of
1.0 amps. Input from a device to the Savant controller is not
supported through a relay. Uses a 3-pin screw-down
connector.
Infrared serial transmitter output ports—use 6-pin screw
down connectors.
Analog stereo audio can be input through the left/right
analog audio input RCA ports.
The VGA connector can support VGA resolutions up to
1920x1200@60Hz. It can also support Component Video
resolutions to 1080p@60hz using a RGB to VGA conversion
cable (not included).
HDMI Type A input ports provide HDMI audio and video
input at video resolutions to 1080p@60hz and graphics
resolutions to 1920x1200@60Hz. The Audio input can be
SPDIF digital Audio, I2S, and HD audio formats.
This port outputs audio and video over a single SC
terminated OM3 multimode fiber. It supports video
resolutions to 1080p@60hz and graphics resolutions to
1920x1200@60Hz. The audio format can be SPDIF digital
audio, I2S, and HD audio formats.
The ground terminal must be connected to an external
ground reference when using PoE.
Connects 12V DC input power to FTC-P100. Provides initial
power up to unit.
Savant Confidential and Proprietary
www.SavantSystems.com
009-0491-00
FTC-P100-00
8 9 10 11