Advertisement
Quick Links
Fits:
2020-Current
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT.
READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
DO NOT OVER TORQUE. STANDARD OPERATING LOAD FOR TIGHTEN
BODY MOUNT NUTS & BOLTS VARIES FROM 45 TO 65 FOOT POUND.
Qty
1
Driver/Left Sidebar
1
Passenger/Right Sidebar
3
Driver/Left Mounting Brackets
3
Passenger/Right Mounting Brackets
6
10-1.5mm x 30mm Hex Bolts
6
10mm Lock Washers
6
10mm x 30mm OD x 2.5mm Flat Washers
Driver/Left Sidebar
Front
PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY
BEFORE STARTING INSTALLATION.
2. Starting from under the front Driver/Left side, temporarily remove the plastic side panel. Move to the floor panel,
locate the square holes and (2) round holes in the pinch weld, (Figure 1). Select (1) 10mm Clip Nut. Attach the
Clip Nut into the square hole in the floor panel, (Figure 2).
3. Select (1) Driver/Left Mounting Bracket. Attach the Bracket to the 10mm Clip Nut with (1) 10mm Hex Bolt, (1)
10mm Lock Washer and (1) 10mm Flat Washer, (Figures 3 & 5). Do not tighten hardware.
4. Attach the Mounting Bracket to the pinch weld with (2) 8mm Hex Bolts, (4) 8mm Flat Washers, (2) 8mm Lock
Washers and (2) 8mm Hex Bolts, (Figure 4). Do not tighten hardware.
5. Move along the body to the center mounting location, (Figure 6). Repeat Steps 2—4 to attach the Mounting
Bracket to the center location, (Figure 7). Do not tighten hardware.
Page 1 of 5
3" Side Bar
Part No. A0064S /B
FORD EXPLORER
Part Description
(3) Passenger/Right
Mounting Brackets
Approx. 24inches
between threaded
PARTS LIST:
Qty
6
10mm Clip Nuts
12
8-1.25mm x 25mm Hex Nuts
12
8-1.25mm x 25mm Combo Bolts
24
8mm x 24mm OD x 2mm Flat Washers
12
8mm Lock Washers
12
8mm Hex Nuts
(3) Driver/Left
Mounting Brackets
Approx. 35inches
between threaded
www.TrailFX.com
Cutting Not
60-180 min
Required
support@trailfx.com
1 866 638 4870
POLISHED STAINLESS STEEL – LIMITED LIFETIME
POWDER COATED BLACK – 3 YEARS
Part Description
Drilling Not
Required
Rev121520
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for TrailFX A0064S
Summary of Contents for TrailFX A0064S
- Page 1 3" Side Bar Part No. A0064S /B Fits: 2020-Current FORD EXPLORER Cutting Not Drilling Not 60-180 min Required Required REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. support@trailfx.com READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. 1 866 638 4870 DO NOT OVER TORQUE.
- Page 2 6. Move to the rear mounting location. Repeat Steps 2—4 to attach the remaining (1) Driver/Left Mounting Bracket, (Figures 8 & 9). Do not tighten hardware. 7. Reattach the plastic side panel. 8. Unwrap the Driver/Left Sidebar. Carefully place Sidebar on the brackets. IMPORTANT: Do not slide or rotate Sidebar on cradles, or damage to the finish may result.
- Page 3 Driver/Left side Installation Pictured Front (Fig 6) Driver/Left Center mounting location Front (Fig 7) Mounting Bracket attached to the Driver/Left center location Front (Fig 8) Driver/Left rear mounting location Front (Fig 9) Mounting Bracket attached to the Driver/Left rear location...
- Page 4 Driver/Left side Installation Pictured Front (2) 8mm Combo Bolts (Fig 10) Attach the Driver/Left Sidebar to the front Mounting Bracket Front (Fig 11) Driver/Left Sidebar attached to the front Mounting Bracket Front (Fig 12) Driver/Left Sidebar attached to the center Mounting Bracket...
-
Page 5: Product Care
Ensure make model year, cab length and bed size of your vehicle is listed in the application. All installation steps are followed correctly. www.TrailFX.com Check out these other TrailFX Products!! Keystone Automotive Operations Inc. (KAO) warrants this product to be free of defects in material and workmanship at the time of purchase by the original retail consumer.
Need help?
Do you have a question about the A0064S and is the answer not in the manual?
Questions and answers