Display Messages - Yamaha MOTIF ES6 Owner's Manual

Display Messages

LCD Indication
Are you sure ? [YES]/[NO]
Arp memory full
Arpeggio type stored
Bad disk or card.
Bulk protected.
Can't find associated files.
Can't undo OK? [YES]/[NO]
Choose user phrase.
Completed.
Copy protected.
Device number is off.
Device number mismatch.
Digital in unlocked.
Disk or card full.
Disk or card not ready.
Disk or card read/write error.
Disk or card write protected.
Effect plug-in is not in slot 1.
Executing...
File already exists.
File not found.
Folder is too deep.
Illegal check box.
Illegal file
Illegal file name.
Illegal input.
Illegal measure.
Illegal phrase number.
Illegal sample data.
Illegal track number.
Incompatible USB device
Meter mismatch
MIDI buffer full.
MIDI checksum error.
MIDI data error.
Mixing stored
Mixing Voice full
Multi plug-in is not in slot 3.
No data.
No DIMM Memory Installed.
No F7 (End of Exc.)
Confirms whether you want to execute a specified operation or not. Press [INC/YES] or [DEC/NO] as required.
The internal memory for Arpeggio data is full, preventing storing the recorded sequence data as an Arpeggio.
The current Arpeggio type has been stored to one of the [SF1] - [SF5] buttons.
The SmartMedia or USB storage device is unusable. Format the SmartMedia or USB storage device and try again.
Bulk data was received when RcvBulk was set to "protect." (See page 264.)
The related voice file cannot be found when loading an AKAI S1000/S3000 format file.
When certain Song/Pattern Jobs are executed, internal memory becomes too full for use of the Undo operation. Press
[INC/YES] if this is OK, or [DEC/NO] to abort the operation. Try again after erasing unwanted Songs, Patterns, or User
phrases.
You have attempted to record a Pattern track to which a preset phrase is assigned. If you wish to use a preset phrase as
raw material for Pattern recording, copy it to a User phrase before recording.
The specified load, save, format, or other Job has been completed.
You have attempted to export or save a copy-protected digital audio source.
Bulk data cannot be transmitted/received since the device number is off.
Bulk data cannot be transmitted/received since the device numbers don't match.
Digital input signal of the AIEB2 is unlocked (not properly received or recorded).
The SmartMedia or USB storage device is full and no more data can be saved. Use a new SmartMedia or USB storage
device, or make space by erasing unwanted data from the SmartMedia or USB storage device.
A SmartMedia or USB storage device is not properly inserted in or connected to the MOTIF ES.
An error occurred while reading or writing to/from a SmartMedia or USB storage device.
The SmartMedia or USB storage device is write protected, or you have attempted to write to a read-only medium such as
CD-ROM.
The Effect Plug-in board does not work because it has not been installed to slot 1. The Effect Plug-in board should be
installed to slot 1.
A format operation or Job is being executed. Please wait.
A file having the same name as the one you are about to save already exists.
The file of the specified type cannot be found on the SmartMedia/USB storage device
Directories below this level cannot be accessed.
No check boxes have been checked in a Sequencer track Job which requires a check box selection. Check the
appropriate check box.
The file specified for loading is unusable by the MOTIF ES or cannot be loaded in the current mode.
The specified file name is invalid. Try entering a different name.
An invalid input or value has been specified. Check the input method or value.
An invalid measure number has been specified in the Song/Pattern mode. Select the measure again.
An invalid phrase number has been specified in the Pattern mode. Select the phrase again.
The sample file specified for loading is unusable by the MOTIF ES.
An invalid track number has been specified in the Song/Pattern mode. Select the track again.
A USB device which cannot be used with the MOTIF ES has been connected to the USB TO DEVICE connector.
In the Pattern Job mode, the meter (time signature) of the destination Pattern is different from the meter of the source
Pattern.
Failed to process the MIDI data because too much data was received at one time.
An error occurred when receiving bulk data.
An error occurred when receiving MIDI data.
In the Song/Pattern mode, the Mixing settings have been loaded from the file.
The Mixing Voice cannot be stored because the number of Voices already stored has exceeded the maximum capacity.
The Multi-Part Plug-in board does not work because it has not been installed to slot 3. The Multi-Part Plug-in board
should be installed to slot 3.
When a Song/Pattern Job is executed, the selected track or range contains no data. Select an appropriate track or
range. In addition, this message appears when a Job related to a Mixing Voice cannot be executed because the
specified Mixing Voice is not available.
An appropriate pair of expansion DIMMs is not properly installed, or the pair is not properly matched (page 289).
Exclusive data has been entered or changed without the necessary "End of Exclusive" byte (F7). Make sure F7 is included.
Explanation
Display Messages
277
Owner's Manual