Display Messages - Yamaha MOX6 Owner's Manual

Appendix

Display Messages

LCD indication
All remote templates stored.
Are you sure?
Arpeggio memory full.
Arpeggio type copied.
Bad USB device.
Bulk protected.
Can't undo. OK?
Completed.
Device number is off.
Device number mismatch.
Edited data will be
discarded.
Edits will be stored by
loading.
Edits will be stored by
saving.
Empty Favorite!
[SHIFT]+[FAVORITE] to add.
Executing...
File already exists.
File not found.
Folder is too deep.
Illegal file name.
Illegal file.
Illegal input.
Illegal measure.
Illegal phrase number.
Illegal Track number.
Incompatible USB device
MIDI buffer full.
MIDI checksum error.
MIDI data error.
Mixing Voice full.
No data.
No F7 (End of Exc.)
No response from USB
device
Not empty folder
Now loading...
Now saving...
Now working...
Overwrite?
Part ** is used for Drum
Assign.
Part ** is used for Layer.
60
MOX6/MOX8 Owner's Manual
Appears when you store the Control Template in the Remote mode.
Confirms whether you want to execute a specified operation or not.
The internal memory for Arpeggio data is full, preventing storing the recorded sequence data as an Arpeggio.
The Arpeggio Types are copied to the [SF1] – [SF6] buttons.
The USB flash memory device connected to this instrument is unusable. Format the USB flash memory device and try
again.
Bulk data cannot be received because of the setting in the Utility mode.
When certain Song/Pattern Jobs are executed, internal memory becomes too full for use of the Undo operation.
The specified load, save, format, or other Job has been completed.
Bulk data cannot be transmitted/received since the device number is off.
Bulk data cannot be transmitted/received since the device numbers don't match.
Prompts you to confirm whether or not to erase the edited data.
Confirms whether or not you want to continue the Load operation. If you select yes, the current edits will be stored.
Confirms whether or not you want to continue the Save operation. If you select yes, the current edits will be stored.
Appears when you press the [FAVORITE] button with no program registered to the Favorite Category.
A format operation or Job is being executed. Please wait.
A file having the same name as the one you are about to save already exists.
The file of the specified type cannot be found.
Directories below this level cannot be accessed.
The specified file name is invalid. Try entering a different name.
The file specified for loading is unusable by this instrument or cannot be loaded in the current mode.
An invalid input or value has been specified. Check the input method or value.
An invalid measure number has been specified in the Song/Pattern mode. Select the measure again.
An invalid phrase number has been specified in the Pattern mode. Select the phrase again.
An invalid Track number has been specified in the Song/Pattern mode. Select the Track again.
A USB device which cannot be used with this instrument has been connected to the USB [TO DEVICE] terminal.
Failed to process the MIDI data because too much data was received at one time.
An error occurred when receiving bulk data.
An error occurred when receiving MIDI data.
The Mixing Voice cannot be stored because the number of Voices already stored has exceeded the maximum capacity.
When a Song/Pattern Job is executed, the selected Track or range contains no data. Select an appropriate Track or range.
In addition, this message appears when a Job related to a Mixing Voice cannot be executed because the specified Mixing
Voice is not available.
Exclusive data has been entered or changed without the necessary "End of Exclusive" byte (F7). Make sure the F7
message is included.
There is no response from the USB device connected to the USB [TO DEVICE] terminal.
You have attempted to delete a folder that contains data.
Indicates that a file is being loaded.
Indicates that a file is being saved.
Canceling the Load/Save operation, after the [EXIT] button has been pressed.
A save operation will overwrite data on the USB flash memory device, and this message confirms whether it is OK to
continue or not.
This message appears when the Part switches of all Parts are set to on, and the Drum Assign function uses Part ** for the
Drum Part in Performance mode. The ** mark indicates the Part number.
This message appears when the Part switches of all Parts are set to on, and the Layer function uses Part ** for the Layer
Part in the Performance mode. The ** mark indicates the Part number.
Description