Related Manuals for Axminster Professional AW15BDS
Summary of Contents for Axminster Professional AW15BDS
- Page 1 Code 111997 Original Instructions AW15BDS Belt & Disc Sander AT20/12/2024 BOOK VERSION: 1...
-
Page 2: Table Of Contents
Table of Contents TABLE OF CONTENTS Specifications Safety guidelines Package contents Operating instructions Maintenance Troubleshooting Exploded view Parts list Conformity Certificates SPECIFICATIONS Motor 230-240V, 50Hz, 250W Speed (no load) 2980RPM Belt size 25 x 762mm Belt speed 14 m/s Disc size 125mm Disc speed 2980RPM... -
Page 3: Safety Symbols
Safety Guidelines IMPORTANT! Safety is the single most important consideration in the operation of this equipment. The following instructions must be followed at all times. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury. There are certain applications for which this tool was designed. - Page 4 Safety Guidelines 2) Electrical safety a. The terminal plug of the tool must fit into the outlet. The plug may not be modified in any way. Do not use an adaptor plug together with grounded power tools. The original plugs and the appropriate outlets reduce the risk of an electrical shock. b.
- Page 5 Safety Guidelines 4) Use and treatment of the power tool a. Do not overtax the tool. Use the appropriate tool for the work that is to be done. With the correct power tool, you can work better and more safely. b.
-
Page 6: Remaining Hazards
Safety Guidelines • Make sure the sanding belt is running correctly so that it cannot come off the drive pulleys. • Make sure the sanding belt is not twisted or loose. • Firmly hold the workpiece when sanding. • Always use the fence when using the sanding machine in horizontal position. •... -
Page 7: Package Contents
Package Contents Package contents No. Description Qty. Belt / disc sander (not shown) Belt work table Inner hex bolt Flat washer Support rod Belt tension handle Disc work table DIsc table locking knob Flat washer + Spring washer Miter gauge Inner hex wrench... -
Page 8: Operating Instructions
Operating Instructions WARNING! Do not plug in or turn on the tool until it is fully assembled according to the instructions. Failure to follow the safety instructions may result in serious personal injury. INSTALL SANDING BELT TABLE 1. Install the supprot rod (1) to the belt frame (2). 2. - Page 9 Operating Instructions MOUNTING BELT / DISC SANDER TO WORKBENCH 1. Place the sander on a surface that is level but also provides enough room on all sides for the workpiece and for the operator (or bystanders) to not be standing in line with the wood while using the tool.
-
Page 10: On/Off Switch
Operating Instructions ON/OFF SWITCH The ON/OFF power switch is located on the front of the sander. 1. Push the GREEN button (I) to turn the machine on. 2. Push the RED button (O) to turn the machine off. • If a failure occurs in the power supply the machine will stop automatically. -
Page 11: Replacing Sanding Disc
Maintenance REPLACING SANDING DISC A sanding disc is pre-mounted at the factory. Use only sanding discs that measures 5 in. (125 mm) in diameter. 1. Remove the disc worktable (1) and then remove the disc cover (2) by removing two screws (3). 2. -
Page 12: Troubleshooting
Troubleshooting Guide WARNING! To avoid injury from an accidental start, turn the switch OFF and always remove the plug from the power source before making any adjustments. PROBLEM PROBLEM CAUSE SUGGESTED CORRECTIVE ACTION Motor will not 1. Short circuit in line, cord or plug. 1. -
Page 13: Exploded Parts Diagram
Exploded Parts Diagram... -
Page 14: Parts List
Parts List Description QTY NO. Description Disc cover end cap Disc sanding paper Stator Disc cap Rotor 44 Phillips screw with flat and spring washer M4X8 Bearing 6202-2RZ Disc work table Wave spring D35 Table support End cap Table lock knob Phillips screw with flat washer M4×153 Big flat washer D6 Hexagon flagne nut M4... -
Page 15: Conformity Certification
Conformity Certification... - Page 16 The packaging is suitable for recycling. Please dispose of it in a responsible manner. EU Countries Only Do not dispose of electric tools together with household waste material. By law they must be collected and recycled separately. Axminster Tools, Axminster Devon EX13 5PH axminstertools.com...
Need help?
Do you have a question about the Professional AW15BDS and is the answer not in the manual?
Questions and answers