Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Vivo STAND-V101BB
Summary of Contents for Vivo STAND-V101BB
- Page 1 Mechanical Arm Single Monitor Desk Mount STAND-V101BB Assembly Manual...
- Page 2 If you do not understand these directions, or if you have any doubts about the safety of the installation, please contact our product support team at 309-278-5303 or help@vivo-us.com for further assistance. Check carefully to make sure there are no missing or defective parts. Failure to report missing parts within 30 days may result in denial of free replacement.
-
Page 3: Package Contents
Package Contents A (x1) B (x1) C (x1) D (x1) Base Upper Arm Lower Arm VESA Plate E (x1) F (x1) G (x1) H (x1) I (x4) Clamp Bracket Base Cable Clip Arm Cable Clip Grommet Sticker Plate Included Hardware & Tools S-A (x1) S-B (x1) S-C (x1) -
Page 4: Assembly Steps
Assembly Steps STEP 1 Remove adhesive backing from Stickers (I) and apply to the bottom of Base (C) as shown. -
Page 5: Option 1: Clamp Installation
STEP 2 Option 1: Clamp Installation For desktops 0.4” - 2” (10-50mm) thick Place Clamp Bracket (E) on the edge of the desktop. Insert M8x75mm Screw (S-B) through the Base (C) and thread into the Clamp Bracket. Tighten using 6mm Allen Wrench (T-C). - Page 6 STEP 3 Slide Lower Arm (B) onto Base (C) and secure by tightening the set screw on the back using 3mm Allen Wrench (T-A). Insert Upper Arm (A) into Lower Arm (B) and secure by tightening the set screw using 3mm Allen Wrench (T-A).
- Page 7 STEP 4 Install VESA Plate (D) to the back of the monitor using appropriate Screws (M-A, M-B) and Washers (M-C). Spacers (M-D) can be used if needed. Tighten using a Phillips screwdriver. Ensure the Lip on VESA Bracket (D) is facing up. Slide monitor with VESA Plate (D) onto the Upper Arm (A) and secure using Thumbscrew (S-A).
- Page 8 STEP 5 Adjusting Monitor Height 2 Person Mounting Recommended Position Mount Arm Turn 10-20x to Set Monitor Height Position the arm horizontally, as shown above, and firmly hold in Turn 5mm Allen Wrench (T-B) 10-20 times place. to obtain proper support for your monitor. Use the guide below to adjust the tension according to the amount of counterbalance Insert...
- Page 9 STEP 6 Remove the bottom cable cover by sliding foward. Organize cables and reattach the cable cover. Attach Arm Cable Clip (G) to Upper Arm (A) as shown.
- Page 10 STEP 7 To adjust the tilt joint, turn the Adjustment Screw using 5mm Allen Wrench (T-B). Adjustment Screw Adjust as desired. ** WARNING ** Do NOT extend monitor behind desk. This may result in tipping.
- Page 11 STEP 8 Insert Base Cable Clip (F) into Base (C). Allen Wrenches (T-A, T-B, T-C) can be stored in Base Cable Clip.
- Page 12 Need Help? We’re Here For You Monday-Friday from 7am-7pm CST Saturday 8am-4pm CST Email Us Chat with Live Agent Give Us a Call help@vivo-us.com www.vivo-us.com 309-278-5303 ext. 1 FOR MORE GREAT VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: WWW.VIVO-US.COM VIVO-us @vivo_us @VIVOus VIVO...
Need help?
Do you have a question about the STAND-V101BB and is the answer not in the manual?
Questions and answers