Page 1
Mechanical Single Monitor Desk Mount with USB STAND-V101BDU Assembly Manual...
Page 2
If you do not understand these directions, or if you have any doubts about the safety of the installation, please contact our product support team at 309-278-5303 or help@vivo-us.com for further assistance. Check carefully to make sure there are no missing or defective parts. Failure to report missing parts within 30 days may result in denial of free replacement.
Package Contents A (x1) B (x1) Pole Spring Arm C (x1) D (x1) E (x1) Lower Arm Base VESA Plate F (x1) G (x1) H (x1) Clamp Bracket Arm Support Cable Clip I (x1) K (x1) J (x1) Arm Cable Clip Pole Cap Grommet Plate L (x1)
Assembly Steps STEP 1 Turn Base (D) upside down. Unscrew Retention Screws (D1) using Phillips screwdriver and separate Cable Housing (D2). Remove plastic coverings from USB and Type-C ports using 3mm Allen Wrench (T-A). 1.1: Insert female end of USB (L) under the housing and the female end of Type-C (M) into Cable Housing.
STEP 2 Option 1: Clamp Assembly 1.1 Desktop Thickness: 0.40” - 1.97” (10mm - 50mm) Place Clamp Bracket (F) on edge of desktop. Thread into Clamp Bracket. Tighten using Insert M8x55mm Screw (S-B) through Base (D) 6mm Allen Wrench. using 6mm Allen Wrench (T-C). Option 2: Grommet Assembly 1.2 Desktop Thickness: 0.40”...
Page 7
STEP 3 3.1: Screw Pole (A) into base, then install Pole Cap (K) into Pole. Tighten Screw using 3mm Allen Wrench (T-A). 3.2: Attach Cable Clip (O) to Pole, then slide on Arm Support (G) and tighten Knob to secure. Knob Knob Screw...
Page 8
STEP 4 Place Lower Arm (C) onto Arm Support (G), and secure by turning the Screw on the support with 3mm Allen Wrench(T-A). Screw Screw Place Spring Arm (B) onto Lower Arm, and secure by turning the Screw on the lower arm with 3mm Allen wrench.
Page 9
STEP 5 Install the VESA Plate (E) to monitor using M4x12mm Screws (M-A) or M4x16mm Screws (M-B) with M5 Washers (M-C) and Spacers (M-D) if neccessary. Ensure Lip is on top during installation of VESA Plate.
Page 10
STEP 6 Place Monitor with VESA Plate (E) on Spring Arm (B). Tighten down Thumbscrew (S-A) to secure. 2 Person Mounting Recommended...
Page 11
STEP 7 Adjusting Monitor Height 2 Person Adjusting Recommended Position Mount Arm Turn 10-20x to Set Monitor Height Position the arm horizontally, as shown above, and firmly hold in Turn 5mm Allen Wrench (T-B) 10-20 times place. to obtain proper support for your monitor. Use the guide below to adjust the tension according to the amount of counterbalance Insert...
Page 12
STEP 8 Remove the bottom cable cover by sliding foward. Organize cables and reattach the cable cover. Attach Arm Cable Clip (I) to Spring Arm (B) as shown.
Page 13
STEP 9 To adjust the tilt joint, turn the Adjustment Screw using 5mm Allen Wrench (T-B). Adjustment Screw Adjust as desired. ** WARNING ** Do NOT extend monitor behind desk. This may result in tipping.
Page 14
STEP 10 Insert Base Cable Clip (H) into Base (D). Allen Wrenches (T-A, T-B, T-C) can be stored in Base Cable Clip.
Page 15
Love Your New Setup? Tag Us on Social! @ VIVO-us @ vivo_us @VIVOus VIVO...
Page 16
Need Help? We’re Here For You Monday-Friday from 7am-7pm CST Saturday 8am-4pm CST Email Us Chat with Live Agent Give Us a Call help@vivo-us.com www.vivo-us.com 309-278-5303 ext. 1 FOR MORE GREAT VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: WWW.VIVO-US.COM VIVO-us @vivo_us @VIVOus VIVO...
Need help?
Do you have a question about the STAND-V101BDU and is the answer not in the manual?
Questions and answers