Related Manuals for OSS OSS-521 Gen4 Backplane
Summary of Contents for OSS OSS-521 Gen4 Backplane
- Page 1 OSS-521 Gen4 Backplane INSTALLATION GUIDE OSS-521 Daisy-Chain Configuration www.onestopsystems.com...
-
Page 2: Table Of Contents
Verify Backplane LEDs ....................... 12 Verify Adapter Card LEDs ......................12 How to Get More Help ..................... 14 Contacting Technical Support ....................... 14 Returning Merchandise ....................... 14 Third Party Hardware & Software Support Policy ................14 Online Support Resources ......................14 OSS-521 Daisy-Chain Setup... -
Page 3: Hardware Requirements
Hardware Requirements Two OSS-521 Backplanes Two 12in ARC cables Two 12in long ARC cables and two OSS-521 backplanes Setup / Installation Set Backplane’s Dipswitches Set the Dipswitches on each backplane appropriately. Refer to the photos below for the corresponding dipswitch settings for each backplane (backplane #1 and backplane #2). -
Page 4: Connect Arc Cables
One Stop Systems Connect ARC Cables Connect the 1 ARC cable to port LANES O-7 (from backplane #1 to backplane #2). Follow the diagram below for connecting the Arc cable. OSS-521 Daisy-Chain Setup... - Page 5 One Stop Systems Connect the 2 ARC cable to port LANES 8-15 (from backplane #1 to backplane #2). Follow the diagram below for connecting the Arc cable. OSS-521 Daisy-Chain Setup...
- Page 6 One Stop Systems Below is the full diagram with two ARC cables connected between two OSS-521 backplanes and with the correct dipswitch settings. OSS-521 Daisy-Chain Setup...
-
Page 7: Connect Power Cables
One Stop Systems Connect Power Cables Connect the ATX power cable to the onboard 24-PIN ATX power connector as shown from the photos below. Connect the 12v Aux power cables to the 12V input connectors. OSS-521 Daisy-Chain Setup... -
Page 8: Install Adapter Card
SW1 #2 = ON; #5 =ON. • SW2 #1 = ON; #2 = ON Note: For more information on different host card dipswitch settings / configurations please check the OSS-PCIe-HIB616-x16 installation guide. Install Target Card Plugin the target card in the upstream slot0 on the backplane #1. -
Page 9: Host Card Installation
Align the host card PCIe connector on top of the PCIe slot. Carefully push the card down until it is firmly seated and secure it. The photos below are example of x16 PCIe slot. • For easy identification on the PCIe slot specification check the label or silk-screen next to the connector. OSS-521 Daisy-Chain Setup... -
Page 10: Cable Installation
Use four Use two cables One cable only Note: Ensure the HIB616-x16 host card is set to x16 configuration, see x16 switch settings. Refer to the OSS-PCIe-HIB616-x16 installation guide. • Plug-in the 1 cable to Port#0 (Top port) on both Target and Host cards •... -
Page 11: Complete Setup
One Stop Systems Complete Setup Below diagram is the completed hardware setup. Host computer is linked to the daisy-chained OSS expansion boards. OSS-521 Daisy-Chain Setup... -
Page 12: Powering Up The Unit
LED2 Solid green LED3 Solid green Link LED Solid green Aux Power Solid green x16 configuration (Four x4 Cables connected) CHO LED will illuminate as solid green, indicates of a stable LINK between Target and Host cards. OSS-521 Daisy-Chain Setup... - Page 13 One Stop Systems When there is no link between Target and Host cards, the CHO LED is OFF. The C9-Aux power LED will illuminate as solid green, which is an indication of power is present on the card. OSS-521 Daisy-Chain Setup...
-
Page 14: How To Get More Help
We assess, certify, and support many third-party hardware and software products along with OSS hardware and are happy to integrate a fully supported system. Ask us about that service and we would be happy to help. If an OSS product is fully functional and a support issue is related to third-party hardware or software that did not ship from the OSS factory, the customer requesting support should reach out to the third-party vendor for assistance to fully troubleshoot the issue. - Page 15 One Stop Systems ONE STOP SYSTEMS 2235 Enterprise Street, Suite#llO, Escondido CA 92029 +1(800)285-8900 +l (760) 745-9883 • +l (760) 745-9824 Toll-Free : US• Main: Fax: www.onestopsystems.com OSS-521 Daisy-Chain Setup...
Need help?
Do you have a question about the OSS-521 Gen4 Backplane and is the answer not in the manual?
Questions and answers