Vivo MOUNT-DLMM1 Assembly Manual
  1. Manuals
  2. Brands
  3. Vivo Manuals
  4. Racks & Stands
  5. MOUNT-DLMM1
  6. Assembly manual
Vivo MOUNT-DLMM1 Assembly Manual

Vivo MOUNT-DLMM1 Assembly Manual

Mount designed for dell optiplex micro
Hide thumbs Also See for MOUNT-DLMM1:

Advertisement

Table of Contents

Mount Designed for
Dell OptiPlex Micro
MOUNT-DLMM1
Assembly Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MOUNT-DLMM1 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Vivo MOUNT-DLMM1

Summary of Contents for Vivo MOUNT-DLMM1

  • Page 1 Mount Designed for Dell OptiPlex Micro MOUNT-DLMM1 Assembly Manual...
  • Page 2 If you do not understand these directions, or if you have any doubts about the safety of the installation, please contact our product support team at 309-278-5303 or help@vivo-us.com for further assistance. Check carefully to make sure there are no missing or defective parts. Failure to report missing parts within 30 days may result in denial of free replacement.

  • Page 3: Assembly Options

    Assembly Options Determine your intended mounting surface and follow instructions as identified below.

  • Page 4: Package Contents

    Package Contents A (x1) B (x1) C (x1) Mounting Plate Locking Plate Clamp D (x2) E (x4) Cable Strap Pads Included Hardware & Tools S-A (x1) S-B (x2) S-C (x8) S-D (x4) Thumbscrew M4x6mm M4x10mm M5x6mm Screw Screw Screw S-E (x4) S-F (x4) S-G (x4) M4 Washer...
  • Page 5 - Assembly Option 1 - VESA Plate Monitor Arm STEP 1 Secure the Mounting Plate (A) to the VESA holes on the back of the monitor using M4x10mm Screws (S-C), M4 Washers (S-E), and a Phillips screwdriver.
  • Page 6 STEP 2 Attach the Locking Plate (B) to the front side of the VESA Plate on your monitor mount using M4x10mm Screws (S-C), M4 Nuts (S-F), and a Phillips screwdriver.
  • Page 7 STEP 3 Secure the Locking Plate (B) to the Mounting Plate (A) with M5x6mm Screws (S-D), M5 Washers (S-G), and a Phillips screwdriver.
  • Page 8 STEP 4 Attach Pads (E) to the PC to protect against accidental damage.
  • Page 9 STEP 5 Place the PC into the mount.. Secure it with Thumbscrews (S-A).
  • Page 10 STEP 6 Attach Cable Straps (D) to the slots on the underside of the assembled mount to secure the charging cord power brick.
  • Page 11 STEP 7 Secure the VESA Plate to the monitor mount following the manufacturer’s guidelines.
  • Page 12 - Assembly Option 2 - Freestanding Monitor STEP 1 Secure the Mounting Plate (A) to the VESA holes on the back of the monitor using M4x10mm Screws (S-C), M4 Washers (S-E), and a Phillips screwdriver.
  • Page 13 STEP 2 Secure the Locking Plate (B) to the Mounting Plate (A) with M5x6mm Screws (S-D), M5 Washers (S-G), and a Phillips screwdriver.
  • Page 14 STEP 3 Attach Pads (E) to the PC to protect against accidental damage.
  • Page 15 STEP 4 Place the PC into the mount. Secure it with Thumbscrews (S-A).
  • Page 16 STEP 5 Attach Cable Straps (D) to the slots on the underside of the assembled mount to secure the charging cord power brick.
  • Page 17 - Assembly Option 3 - Desk Clamp Pg 17: Desktop Thickness: 0.40”-1.57”(10mm-40mm) Pg 18: Desktop Thickness: 0.59”-1.96”(15mm-50mm) STEP 1 Remove Lower Clamp (C1) using a Phillips Disassemble Clamp (C) using a Phillips screwdriver. screwdriver. Turn Lower Clamp upside down and reassemble. Reassemble Clamp as shown above.

  • Page 18: Flush Installation

    STEP 2 Choose the desired mounting orientation and attach the Mounting Plate (A) to the back of Clamp (C) at the preferred height using M4x6mm Screws (S-B) and a Phillips screwdriver. Above Desk Installation Flush Installation This manual continues with images for Above Desk Installation.
  • Page 19 STEP 3 Secure the Locking Plate (B) to the back of the Mounting Plate (A) with M5x6mm Screws (S-D), M5 Washer (S-G), and a Phillips screwdriver.
  • Page 20 STEP 4 Place the assembly on the desktop and tighten the hand bolt to secure it. Follow the same directions if you selected Flush Installation.
  • Page 21 STEP 5 Attach Pads (E) to the PC to protect against accidental damage.
  • Page 22 STEP 6 Place the PC into the mount. Secure it with Thumbscrews (S-A).
  • Page 23 STEP 7 Attach Cable Straps (D) to the slots on the underside of the assembled mount to secure the charging cord power brick.
  • Page 24 Need Help? We’re Here For You Monday-Friday from 7am-7pm CST Saturday 8am-4pm CST Email Us Chat with Live Agent Give Us a Call help@vivo-us.com www.vivo-us.com 309-278-5303 ext. 1 FOR MORE GREAT VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: WWW.VIVO-US.COM VIVO-us @vivo_us @VIVOus VIVO...

Table of Contents