Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for BWT AQA drink OFFICE
Summary of Contents for BWT AQA drink OFFICE
- Page 1 AQA drink OFFICE I N S T A L L A T I O N AND U S E M A N U A L...
- Page 2 All products comply with Ministerial Decree 25/2012 and Ministerial Decree 174/2004. Installation must be carried out in compliance with current regulations and must be performed by a qualified installer in accordance with Ministerial Decree 37/2008. ATTENTION: This equipment requires regular maintenance to ensure the potability requirements of the water and the maintenance of the improvements as stated by the manufacturer.
- Page 3 Decree-Law 151 of 22 July 2005 on the reduction of the use of hazardous substances in electrical and electronic equipment and the disposal of waste. ◼ BWT Italia Srl operates with a certified Quality System in compliance with the requirements of the UNI EN ISO 9001:2008 Standard, with Certificate No. 677 issued by CERTIQUALITY GENERALITY Dear Customer, Thank you for choosing a BWT branded product.
- Page 4 ◼ Installation, extraordinary maintenance and repairs may only and exclusively be carried out by qualified and specialised personnel authorised by the manufacturer; always contact your authorised BWT ITALIA S.r.l. dealer or service centre. ◼ The water supply to the appliance must be exclusively potable water.
- Page 5 After placing the machine in position, it is necessary to proceed with the power supply connection operations. If the dispenser is placed above a floor and the CO2 cylinder and BWT Bewapur HQ filter (if fitted) are housed underneath it, provide a suitable hole for the water supply hose (¼...
- Page 6 WATER CONNECTIONS (POTABLE WATER) and CO2 (FEED E290) ATTENTION: It is mandatory to install a cold water stopcock at the connection point. Back photo Connection to the drinking water network. In order for the dispenser to function properly over time, do not make any temporary connections. In addition, the following work must be carried out by qualified personnel.
- Page 7 If the optional prefilter is present, proceed as follows: ◼ steps 1) to 3) above are carried out ◼ you cut the water supply pipe at the insertion point of the pre-filter the supply pipe on the shutoff valve side is connected to the inlet connection of the prefilter ◼...
- Page 8 Photo detail rear thermostat FREE INITIAL VISIT After completion of all installation work, the BWT Service Department is at your disposal for a free initial inspection. During the inspection, the user is shown how to operate the unit. I N S T A L L A T I O N A N D U S E - A Q A D R I N K O F F I C E...
- Page 9 STARTING CAUTION: Identify the model of the appliance before starting it, and strictly follow the specific starting procedures. After making the hydraulic connection, proceed as follows: place an appropriately sized container under the dispensing terminal; open the water shutoff valve. After connecting the dispenser to the water and electricity supply following the instructions in the previous section, you should proceed as follows: Screw the CO2 cylinder onto the pressure reducer;...
- Page 10 If the appliance has not been used for a long period of time (switched off for one or more weeks e.g. holiday period) or when replacing the BWT Bewapur filter cartridge, it is obligatory to carry out periodic sanitisation when switching back on, following the procedures in the appliance sanitisation kits at the point of use.
- Page 11 Photo extraction drip tray The appliance is equipped with an anti-flooding probe located on the base plate of the technical compartment. The probe, if wet, blocks the dispensing keyboard. Again, the problem is highlighted by a buzzer, flashing and a keypad lock. To restore it, it is necessary to solve the problem that caused the loss and/or to contact the Technical Assistance Service.
- Page 12 1) The dispenser is guaranteed, in accordance with the following, for a period of 24 months, commencing on the date of invoicing, and with an identification plate bearing intact serial numbers. 2) Warranty' means the free replacement of dispenser components acknowledged by BWT ITALIA S.r.l. to be defective in manufacture or material.
- Page 13 PROBLEMS, CAUSES AND REMEDIES Once installation is complete and before starting up, check that all operations have been carried out correctly. Use this form to request a free initial visit to our nationwide service centres. PROBLEM CAUSE REMEDY Open the shut-off valve Main water tap closed Crushed or choked mains connection pipe Check the pipe route...
- Page 14 CUSTOMER INTERVENTION REGISTER: DEVICE: Specialised Technical Date Service Sheet Intervention type Assistance Centre Intervention type: AV= start-up - MA= maintenance - GA= warranty - AB= subscription - RI= repair I N S T A L L A T I O N A N D U S E - A Q A D R I N K O F F I C E...
- Page 16 BWT Italy +39 02 2046343 info@bwt.it bwt.com F O R Y O U A N D P L A N E T B L U E .
Need help?
Do you have a question about the AQA drink OFFICE and is the answer not in the manual?
Questions and answers