Woodbridge EBT350 Installation And Care Manual

Electronic bidet toilet
Hide thumbs Also See for EBT350:

Advertisement

Available languages

Available languages

Quick Links

INSTALLATION AND CARE GUIDE
ELECTRONIC BIDET TOILET
Compliance with the following codes & standard:
• 2015 Uniform Plumbing Code
• 2018 International Plumbing Code
• 2018 International Residential Code
• CSA B45.5 / IAPMO Z124-2017- Plastic Plumbing Fixtures
SCC Accredited
Accrédité
READ ALL INSTRUCTIONS BEFORE UNPACKING THE PRODUCT
INSTRUCTIONS THAT, IF IGNORED COULD RESULT IN DEATH OR SERIOUS INJURY CAUSED BY INCORRECT HANDLING
OR INSTALLATION OF THE PRODUCT. THESE INSTRUCTIONS MUST BE OBSERVED FOR SAFE INSTALLATION.
We reserves the right to change, update, modify, alter, redesign this manual/product or its policies without prior notice!
We
shall not be liable for any injuries or property damages in connection with this product during installation or use of this product!
This products must be installed by a fully insured and licensed plumber only. Installation of any our product by anyone other
than fully insured and licensed plumber shall void limited warranty. We recommends that such licensed plumber have experience
in the installation of products.
Limited warranty is void on any commercial installation
We are not responsible for local code compliance for this product. Building and plumbing codes may vary from state-to-state in
accordance to your location. We are not responsible for providing any compliance certifications.
Under no circumstances we are shall not be liable for any and all incidental damages sustained in connection with this product
Neither manufacture, nor distributor, nor retailer is responsible for water damage or flood caused due to use of this product.
Under no circumstances We shall not be liable for any and all fees, cost of installation/reinstallation/removal, subsequent
damage or transportation in case of the product defect
®
CB-P/S
ANSI
ACCREDITED
ISO/IEC 17065
OCPS
Product Certification Body
CCN
#1000
2 PEOPLE ARE REQUIRED TO LIFT AND DURING
ENTIRE INSTALLATION OF THIS PRODUCT
INSTALLATION OF THIS PRODUCTS BY AN
INEXPERIENCED INSTALLER MAY RESULT
PERSONAL INJURY OR DEATH!
www.woodbridgebath.com
Model:
( UPC )
( IPC )
®
®
( IPC )
PREFERED
EDUCATION
PROVIDER
EBT350

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EBT350 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Woodbridge EBT350

  • Page 1 INSTALLATION AND CARE GUIDE ELECTRONIC BIDET TOILET Model: EBT350 Compliance with the following codes & standard: ( UPC ) ® • 2015 Uniform Plumbing Code ( IPC ) ® • 2018 International Plumbing Code ® ( IPC ) • 2018 International Residential Code •...
  • Page 2: List Of Materials

    List of materials TOILET COMPONENTS During unpacking the product and prior to installation inspect your new product for any damages or missing parts. Do not attempt to install or operate the product if the product is damaged. Installation Manual Remote Control Installation Manual Rough-in Template Components...
  • Page 3: Important Safeguards

    IMPORTANT SAFEGUARDS When using electrical products, especially when children are present, basic safety precautions should always be followed, including the following: 1. The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.
  • Page 4: Grounding Instructions

    CAUTION – Indicates that failure to follow the instruction may cause body injury or property damage. 1. Do not install or use the product in wet places as steam room etc. 2. It is recommended to use water-proof electrical outlet which should be installed in a place where is not easily to get wet.
  • Page 5 Technical Model Model EBT350 Rated voltage 110V-120V, 50Hz-60Hz Rated power 875W Main Unit Water proof IPX4 Power cord length About 1.5m Flush volume 1.6/1.1Gpf, 6.0L(full flush)/4.1L(half flush) Flushing mode Siphonic jet Rough-in 12 inches (305mm) Toilet Outlet outside diameter ≤ 3.9 inches (≤ 100mm)
  • Page 6 Technical Model Warm air volume Over 0.2m3/min Warm air temperature 6-level adjustment Drying Heating power 230W device Thermal fuse, Thermostat, Leakage protection Safety device plug, Wind temperature sensor Surface temperature 6-level adjustment Heating power Heated seat After 10 minutes of use, the seat temperature Burn protection will automatically drop slowly to a low level Seat sensor, Temperature sensor, Thermostat,...
  • Page 7: Dimensions/Technical Data

    DIMENSIONS/TECHNICAL DATA 27-5/8 ″ IMPORTANT INFORMATION • Measurements are +3/8" and subject to change without notice • Please note that installer(s) must be certify or warranty will be voided. • Specifications & Configurations are subject to change without notice • Measurements herein supersede all others published prior to •...
  • Page 8 DIMENSIONS/TECHNICAL DATA 3″ 11 1/4″ 1.The product drawing is for reference only, and we reserve the right to modify the appearance of the product. 2.If the appearance of the product is changed, the actual product shall prevail. www.woodbridgebath.com...
  • Page 9: Standard Installation

    DIMENSIONS/TECHNICAL DATA Installation Option 19-5/8" 15-3/4" Recommended location for remote control mounting (Left or Right) water inlet new hose angle valve Connect the water inlet and angle valve of the 1-3/4" 20-7/8" toilet with the matching hose and tighten it Rough-in 12"...
  • Page 10: Parts Identification

    Parts identification Left side Bumper Foam shield filling drawer Seat knob Ceramic toilet Right side Nozzle shield Dryer shield Night light sensor window Front Rear washing washing Spray nozzle Touch the sensing area with foot (optional) www.woodbridgebath.com...
  • Page 11 Toilet installation Install the matching three-way angle 3. Installation of battery box valve • Before activating the power-off flushing function, install a 9V alkaline battery (not • Mark the center line of the sewage outlet supplied) into the battery box in advance. on the ground, and install a three-way angle valve at a suitable position on the •...
  • Page 12 Toilet installation 4. Mounting bracket installation 6. Screw installation • Assemble the mounting bracket with • Put the screw through the fixing sleeve bolts and then install them to the and then install it through the holes (on pre-installed flange plate on the ground both sides of the toilet ceramic) to the and lock tight with nuts.
  • Page 13 Toilet installation the water inlet hose of the toilet seat • Put the funnel into the filling port, hold it, and slowly pour the foam liquid into the funnel with the other hand. (Do not quickly pour the foam liquid into the funnel to avoid the foam liquid overflowing) the water supply hose of the toilet tank...
  • Page 14 Preparation Turn on the three-way angle valve • Check the threaded connection for leaks to ensure complete sealing. Turn the three-way angle valve counterclockwise to the full open position. (Note: The three-way angle valve opens with a large torque for the first time.) Equipped with three-way angle valve...
  • Page 15 Auto open/close lid The intelligent toilet can achieve the function of auto lid open/close. On closed situation, so please function the auto lid open/close function by using remote controller. If the model you purchased is with foot sensor 1. Approaching the toilet 1.
  • Page 16: Filter Maintenance

    Maintenance Main unit care and maintenance 3. Use only a soft cloth or soft brush to clean. Do not pull or push the wand, to 1. Shut off power supply before doing avoid damage. maintenance. 2. Use only a soft, damp cloth to clean. Avoid using harsh chemicals.
  • Page 17: Emergency Troubleshooting

    Emergency troubleshooting Power and water failure 48.5mm • Fill up 2.1Gal (8L) water to a bucket and 46.4mm 17.5mm flush the ceramic bowl. Note: Avoid water spilling from bowl. Male buckle (+) Female buckle (-) Note: 1. It is recommended to hire professional personnel for this operation.
  • Page 18 Description of the knob function 1. With seated, rotate the knob clockwise to activate the front washing function, and rotate the knob counterclockwise to activate the rear washing function. 2. When the human body is seated and the function is not turned on, press and hold the knob of the main unit to turn on the drying function.
  • Page 19 Description of the top indicator lights ① ④ ② ⑤ ⑥ ③ ① ECO energy saving ④ Smart night light ② ⑤ Water temperature Seat temperature ③ Water temperature display ⑥ Seat temperature display 1. During the power-on self-test phase, the water temperature, seat temperature, ECO, and smart night light icons light up, and the temperature displays 88°F.
  • Page 20: Troubleshooting Guide

    Troubleshooting guide Problem Cause Solution Water supply hose is kinked Straighten the hose to remove the kink No water Angle valve is off Turn on the angle valve from nozzle A water failure occurred Restore the water supply Water supply hose is kinked Straighten the hose to remove the kink Poor water spraying...
  • Page 21 Troubleshooting guide Problem Cause Solution User is not within the Adjust position on seat to activate the sensing area of the seat sensor Malfunction of It is normal for the deodorizing function deodorization Deodorization function to continue operating after user leaves, continues after user leaves for complete odor removal Foam shield has a...
  • Page 22: Warranty

    WARRANTY WOODBRIDGE Bathtub, Whirlpool/Air Bubble Massage Tub, Cold Plunge,1 Year limited to be free of defects in material and workmanship. Sauna room and Sauna Tent : 1 Year limited to be free of defects in material and workmanship. Toilet and Bidet : 1 Year limited to be free of defects in material and workmanship.
  • Page 23 IMPORTANT! DO NOT USE: Abrasive cleaners such as: acid, ammonia, bleach, and similar solutions. Use of such solutions may cause corrosion, finish peeling, and/or dull the surface. DO NOT USE: Abrasive sponges or cloth. Never use steel, wool, or wired brushes that will permanently scratch the www.woodbridgebath.com...
  • Page 24 GUIDE D'INSTALLATION ET DE MAINTENANCE BIDET DE TOILETTE ÉLECTRONIQUE Modèle EBT350 Conformité avec les codes et normes suivants: ( UPC ) ® • 2015 Uniform Plumbing Code ( IPC ) ® • 2018 International Plumbing Code ® • Code résidentiel international 2018 ( IPC ) •...
  • Page 25 Liste des matériaux COMPOSANTS DES TOILETTES Lors du déballage et avant l'installation, vérifiez le produit pour détecter tout dommage ou pièce manquante. Ne tentez pas d'installer ou d'utiliser le produit s'il est endommagé. Installation Manual Unité de Manuel d'installation Modèle d'ébauche télécommande Unité...
  • Page 26 DES GARANTIES IMPORTANTES Lors de l'utilisation de produits électriques, en particulier en présence d'enfants, il convient de toujours respecter les mesures de sécurité de base, notamment les suivantes : 1. L'appareil ne doit pas être utilisé par des personnes (y compris des enfants) dont les capacités physiques, sensorielles ou mentales sont réduites, ou qui manquent d'expérience et de connaissances, à...
  • Page 27: Instructions De Mise A La Terre

    ATTENTION – Indique que le non-respect de l'instruction peut entraîner des blessures corporelles ou des dommages matériels. 1. N'installez pas ou n'utilisez pas le produit dans des endroits humides tels que les hammams, etc. 2. Il est recommandé d'utiliser une prise électrique étanche qui doit être installée dans un endroit où elle ne risque pas d'être mouillée.
  • Page 28: Unité Principale

    Modèle technique Modèle EBT350 Tension nominale 110V-120V, 50Hz-60Hz Puissance nominale 875W Unité principale Etanchéité à l'eau IPX4 Longueur du cordon Environ 1.5m d'alimentation Volume de rinçage 1.6/1.1Gpf, 6.0L(full flush)/4.1L(half flush) Mode de rinçage Jet siphonique Raccordement 12 pouces (305mm) Toilettes Diamètre extérieur de la sortie...
  • Page 29 Modèle technique Volume d'air chaud Plus de 0.2m3/min Température de l'air chaud 6 niveaux de réglage Dispositif de séchage Puissance de chauffage 230W Fusible thermique, Thermostat, Bouchon de protection Dispositif de sécurité contre les fuites, Capteur de température du vent Température de surface Réglage à...
  • Page 30 DIMENSIONS/DONNÉES TECHNIQUES 27-5/8 INFORMATIONS IMPORTANTES • Les mesures sont de +3/8 po et peuvent être modifiées sans préavis. • Veuillez noter que l'installateur doit être certifié sous peine d'annulation • Les spécifications et les configurations peuvent être modifiées de la garantie. sans préavis.
  • Page 31 DIMENSIONS/DONNÉES TECHNIQUES 11 1/4po 1.le dessin du produit est fourni à titre de référence uniquement, et nous nous réservons le droit de modifier l'apparence du produit. 2.Si l'apparence du produit est modifiée, c'est le produit réel qui prévaut. www.woodbridgebath.com...
  • Page 32: Installation Standard

    DIMENSIONS/DONNÉES TECHNIQUES Option d'installation 19-5/8po 15-3/4po Emplacement recommandé pour le montage de la télécommande (gauche ou droi) entrée d'eau nouveau tuyau vanne d'angle Raccordez l'arrivée d'eau et le robinet 1-3/4po 20-7/8po d'équerre des toilettes avec le tuyau Rough-in 12po correspondant et serrez-le. Standard INSTALLATION INSTALLATION NON VISIBLE...
  • Page 33: Identification Des Pièces

    Identification des pièces Côté gauche Pare-chocs Couvercle Bouclier en mousse Tiroir de remplissage Siège Bouton Toilette en céramique Côté droit Bouclier de la buse Bouclier de séchage Capteur de la télécommande Lavage Lavage avant arrière Buse de pulvérisation Toucher la zone de détection avec le pied (en option) www.woodbridgebath.com...
  • Page 34: Installation Des Toilettes

    Installation des toilettes Installer le vanne d'angle à trois voies 3. Installation du boîtier de batterie • Marquez l'axe de la sortie des eaux usées sur • Avant d'activer la fonction de rinçage hors le sol et installez un té à un endroit approprié tension, installez une pile alcaline de 9V (non sur le mur en fonction de la taille des toilettes.
  • Page 35 Installation des toilettes 4. Installation du support de montage 6. Installation de la vis • Assemblez le support de montage avec les • Faites passer la vis dans le manchon de boulons, puis installez-les sur la plaque de fixation, puis installez-la dans les trous (des la bride préinstallée au sol et verrouillez-les deux côtés de la céramique des toilettes) avec les écrous.
  • Page 36 Installation des toilettes • Placer l'entonnoir dans l'orifice de remplissage, le tuyau d'arrivée d'eau le tenir et verser lentement la mousse du siège des toilettes liquPlacer l'entonnoir dans l'orifice de remplissage, le tenir et verser lentement la mousse liquide dans l'entonnoir avec l'autre main.
  • Page 37 Préparation Allumer three-way vanne d'angle • Vérifier l'étanchéité du raccord fileté. Tournez le vanne d'angle à trois voies dans le sens inverse des aiguilles d'une montre jusqu'à la position d'ouverture complète. (Remarque : la première fois, le vanne d'angle à trois voies s'ouvre avec un couple important). Équipé...
  • Page 38 Couvercle à ouverture/fermeture automatique Les toilettes intelligentes peuvent assurer la fonction d'ouverture/fermeture automatique du couvercle. En cas de fermeture, veuillez utiliser la fonction d'ouverture/fermeture automatique du couvercle à l'aide de la télécommande. Si le modèle que vous avez acheté est équipé d'un capteur de pied 1.
  • Page 39: Entretien Du Filtre

    Maintenance Entretien et maintenance de l'unité 3. Utilisez uniquement un chiffon doux ou une principale brosse douce pour le nettoyage. Ne pas tirer ou pousser la brosse pour éviter de 1. Coupez l'alimentation électrique avant de l'endommager. procéder à l'entretien. 2.
  • Page 40 Dépannage d'urgence Panne d'électricité et d'eau 48.5mm Versez environ 8 litres d'eau dans un 46.4mm 17.5mm tonneau et rincez le bol en céramique. Remarque: Évitez que l'eau ne s'écoule de Boucle la cuvette. mâle (+) Boucle femelle boucle (-) RemarqueRemarque: 1.
  • Page 41 Description de la fonction du bouton 1. En position assise, tournez le bouton dans le sens des aiguilles d'une montre pour activer la fonction de lavage avant, et dans le sens inverse des aiguilles d'une montre pour activer la fonction de lavage arrière. 2.
  • Page 42 Description de l'indicateur supérieur ① ④ ② ⑤ ⑥ ③ ① Économie d'énergie ECO ④ Veilleuse intelligente ② Température de l'eau ⑤ Température du siège ③ Affichage de la température ⑥ Affichage de la température de l'eau du siège 1. Pendant la phase d'autotest à la mise sous tension, les icônes de la température de l'eau, de la température du siège, de l'ECO et de la veilleuse intelligente s'allument, et la température affiche 88°F.
  • Page 43: Guide De Dépannage

    Guide de dépannage Problème Cause Solution Le tuyau d'alimentation Redresser le tuyau pour éliminer le pli en eau est plié Pas d'eau à la buse Le vanne d'angle est fermé Ouvrir le vanne d'angle Une coupure d'eau s'est produite Rétablir l'alimentation en eau Le tuyau d'alimentation en Redresser le tuyau pour éliminer le pli Mauvaise...
  • Page 44 Troubleshooting guide Problem Cause Solution L'utilisateur ne se trouve pas dans Régler la position sur le siège pour activer le capteur la zone de détection du siège Dysfonctionnement Il est normal que la fonction de désodorisation de la désodorisation continue à fonctionner après le départ de La fonction de désodorisation se l'utilisateur, pour une élimination complète poursuit après le départ de...
  • Page 45: Garantie

    Cette garantie limitée exclut tout usage industriel, commercial et professionnel. Une preuve d'achat (ticket de caisse original) de l'acheteur original, une description et des photos du défaut, le numéro ou la description du modèle doivent être fournis à Woodbridge Bath pour toute réclamation au titre de la garantie et Woodbridge Bath N'EST PAS responsable des coûts de main-d'œuvre, d'enlèvement ou d'installation.
  • Page 46 www.woodbridgebath.com...
  • Page 47 www.woodbridgebath.com...
  • Page 48 Conservez ces instructions d'installation pour référence future! Merci d'utiliser les produits WOODBRIDGE! Si vous avez des questions ou des préoccupations, n'hésitez pas à nous contacter. Téléphone du service à la clientèle: 562-229-0088. (9 h à 17 h, heure normale du Pacifique, du lundi au vendredi) ou par courriel à: help@woodbridgebath.com...

Table of Contents