Related Manuals for activTek INDUCT 2000+ OZONE
Summary of Contents for activTek INDUCT 2000+ OZONE
- Page 1 I N D U C T 2 0 0 0 + OZO N E I N D U C T 7 5 0 + O Z O N E DUCT MOUNTED SURFACE & AIR PURIFICATION SYSTEM READ MANUAL CAREFULLY FOR PROPER USE AND OPTIMAL OPERATION.
-
Page 2: Table Of Contents
GENERAL INFORMATION PRODUCT OVERVIEW Congratulations on your purchase of the activTek Induct 750 Ozone or activTek Induct 2000 Ozone air purification enhancement system! The unit is easily mounted into the supply side of air conditioning and heating system air ducts by an electrician or HVAC professional, where it will provide surface and air disinfection while the HVAC system is running. -
Page 3: Important Safety Instructions
Ozone require power 24/7; DO NOT install where power to the unit will be cycled on and off Location for Protective Earth Line. Read this manual in its entirety before using your activTek Induct 750 Ozone or activTek Induct 2000 Ozone. -
Page 4: Product Features
PRODUCT FEATURES It is important to be familiar with the parts of the activTek Induct 750 Ozone and activTek Induct 2000 Ozone. If any parts are missing, contact your sales representative or Distributor. Duct Mounting Plate activTek Cell Assembly ®... -
Page 5: Installation Requirements
CAUTION • The activTek Induct 750 Ozone and activTek Induct 2000 Ozone require power 24/7; DO NOT install where power to the unit will be cycled on and off 1 Unit should be installed after the air handler in the HVAC system. -
Page 6: Installing The Unit
• When the unit is installed in a roof mounted HVAC system, the unit must be protected from elements CAUTION • The activTek Induct 750 Ozone and activTek Induct 2000 Ozone require power 24/7; DO NOT install where power to the unit will be cycled on and off Find the optimal position downstream from the air handler. - Page 7 10. Plug unit into working power receptacle. Duct Mounting Plate with (4) thumb nuts. NOTE: The activTek Induct 750 Ozone and activTek Induct 2000 Ozone require power 24/7. Do not install where power to the unit will be cycled on and off.
-
Page 8: Wiring The Unit
CAUTION power 24/7; DO NOT install where power to the unit will be cycled on and off 1. Connect wires coming from the activTek Induct 750 Ozone or activTek Induct 2000 Ozone unit as follows: NOTE: All units come standard with a blunt cord. -
Page 9: Replacing The Activtek ® Cell Assembly
OSHA electrical lockout safety requirements to prevent accidental release WARNING of energy during service or maintenance activities For optimal performance and to maintain the Limited 5 year warranty, it is required to replace the activTek Cell Assembly once every 12 months, ® CAUTION even if the UV Bulb appears to be operating normally. -
Page 10: Replacing The Ballast
Visit lamprecycle.org for proper bulb disposal regulations REPLACING THE BALLAST • Never attempt to check operation of the activTek Cell Assembly by direct ® observation; severe eye damage can result; use the indicator lamps on the bottom of the ballast only •... - Page 11 REPLACING THE BALLAST (CONTINUED) 3. Disconnect all ballast wiring by 4. Remove the two (2) nuts 5. Place new ballast into the pressing down on connector tabs securing ballast to the case. original location and secure and pulling wire straight out. Remove the ballast.
-
Page 12: Replacement Parts & Service
REPLACEMENT PARTS & SERVICE Use only replacement parts recommended by the manufacturer. WARNING REPLACEMENT PARTS FOR ACTIVTEK INDUCT 750 OZONE PART NUMBER activTek Cell Assembly US71114 (NOT available in California) Ballast 9950102 REPLACEMENT PARTS FOR ACTIVTEK INDUCT 2000 OZONE PART NUMBER... -
Page 13: Warranty Information
Induct 750 Ozone or activTek 2000 Ozone ARE HEREBY EXPRESSLY DISCLAIMED, INCLUDING ANY unit is connected to the fan circuit where the activTek Cell IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS ® Assembly cycles “ON and OFF” with the system fan, the FOR A PARTICULAR PURPOSE. -
Page 14: Fcc Declaration & Responsible Party
Class B digital device, pursuant of activTek Induct 2000 Ozone Part 15 of the FCC Rules. These limits are designed to provide reasonable Model: A1022C (activTek Induct 750 Ozone) protection against harmful interference A1023C (activTek Induct 2000 Ozone) in a residential installation. This... - Page 16 For information regarding the use of this product, please call Customer Service. 866.736.0503 support@activTek.net activTek Environmental, LLC 1300 Valley Drive Bristol, VA 24201 866.736.0503 Assembled in U.S.A. | © activTek Environmental, LLC. All Rights Reserved...
Need help?
Do you have a question about the INDUCT 2000+ OZONE and is the answer not in the manual?
Questions and answers