Related Manuals for activTek OzoneBlaster
Summary of Contents for activTek OzoneBlaster
- Page 1 OZONE BLASTER ADJ CE OZONE BLASTER ADJ Electronic Air Purification System READ MANUAL CAREFULLY FOR PROPER PROCEDURES AND OPERATION.
-
Page 2: Table Of Contents
Please record the name and phone of your activTek Distributor: Name___________________________________________________________________________ Phone __________________________________________________________________________ Please record the serial number of your Ozone Blaster by activTek: Serial # _________________________________________________________________________ CAUTION: This unit is to be used in unoccupied areas only . WARNING: DO NOT operate this unit without the lint screen installed . -
Page 3: Applications
MECHANICAL: • 52 CFM • One front-mounted control for ozone output SIZE: • Height: 11 3/4"; Width: 8"; Depth: 9 3/4" • Weight: 16 pounds OZONE OUTPUT: • 0-1,200mg per hour This owner’s manual is also available online at: http://www.activTek.net... -
Page 4: Principles Of Operation
PRINCIPLES OF OPERATION Nature cleans the air with the lightning and rain . Lightning bolts produce ozone which cleans the air naturally . Rain helps bring the ozone closer to the earth's surface . They are then attracted to atmospheric contaminants that are either removed from the air and attached to grounded objects or are oxidized . -
Page 5: Placing The Unit
PLACING THE UNIT Place the unit as high as possible (5 to 6 feet from the floor – top of a bookshelf, high cabinet, etc . ) and at least 6 inches from wall or other obstruction for maximum effectiveness . Do not point the unit towards a wall or directly at the ceiling . -
Page 6: Ozone Plate Installation
OZONE PLATE INSTALLATION The Ozone Blaster utilizes two ozone plates . Unplug the unit before doing any work . Remove two (2) screws and clip from top of unit . Remove filter by tilting and pulling up . Fully insert the ozone plates (a & b) between the guide-grooves in the top and bottom of the plate cage (between the posts and clips) making sure the metal clip on each side of the plate is in... -
Page 7: Lint Screen Installation
LINT SCREEN INSTALLATION Always install bottom of lint screen first . The lint screen should depress the safety switch . Fit top of lint screen into cabinet . Lint Unit will not operate if safety switch is not depressed . Screen Safety SETTING/ADJUSTING... -
Page 8: Maintenance
SETTING/ADJUSTING (CONTINUED) 4. TREATING AN AREA 4a. SITE PREPARATION • Remove the contaminant or debris that may be associated with the source of the problem . • Clean excess contaminate residue off surfaces . • Seal the environment intended to be treated . Close vents and air returns . It may be necessary to seal off return vents to prevent leakage of ozone into other areas . - Page 9 MAINTENANCE (CONTINUED) OZONE PLATE Carefully remove the plates (a & b) from the card cage by grasping the middle of the edge nearest to you and slowly pulling straight out . For all applications - Clean with 50% ammonia and 50% water to remove contaminates .
-
Page 10: Troubleshooting
TROUBLESHOOTING I have plugged in the unit, turned "ON" the power switch and nothing happens… what's wrong? • Make sure cord is securely plugged into the back of the unit and into a working electrical outlet . • Check the lint screen located at the back of the machine to ensure that the safety switch activator clip depresses the safety switch . - Page 11 • Is the unit properly placed away from objects that may obstruct air flow? • Are the filter and fan housing clean? If your unit fails to operate properly after performing troubleshooting, contact your activTek Distributor . For further assistance, contact us at the address located on the back of the manual, or visit www .activTek .com .
-
Page 12: Warranty
Internet presence for with the Owner’s Manual . Failure to you specific legal rights and you may activTek products is www . a ctivTek . meet any of these requirements will void also have other rights which vary from net .