Download
Share
Print this page
Lumag WS 700T Original Operating Instructions
  1. Manuals
  2. Brands
  3. Lumag Manuals
  4. Power Tool
  5. WS 700T
  6. Original operating instructions
Lumag WS 700T Original Operating Instructions

Lumag WS 700T Original Operating Instructions

Hide thumbs

Advertisement

Quick Links

Download this manual
Translated from German to English - www.onlinedoctranslator.com
jigsaw
original operating instructions
WS 700T
WS 700T‐230
Both the model number and the serial number can be found on the nameplate on the machine.
You should keep both numbers safe so that you can access them in the future. This
Instructions explain the functions and applications of the machine.
FOR YOUR SAFETY
Before using the device, read the operating instructions,
Safety and warning instructions must be observed!

Advertisement

loading
Need help?

Need help?

Do you have a question about the WS 700T and is the answer not in the manual?

Questions and answers

Related Manuals for Lumag WS 700T

Summary of Contents for Lumag WS 700T

  • Page 1 Translated from German to English - www.onlinedoctranslator.com jigsaw original operating instructions WS 700T WS 700T‐230 Both the model number and the serial number can be found on the nameplate on the machine. You should keep both numbers safe so that you can access them in the future. This Instructions explain the functions and applications of the machine.
  • Page 2 Project ID: GAMUL W5 Rev. status: 2024-10-28 © LUMAG GMBH Rudolf-Diesel-Str. 1a 84375 Kirchdorf a.Inn Tel.: +49 8571 92556-0 Fax: +49 8571 92556-19 E-mail:info@lumag-maschinen.de Internet:www.lumag-maschinen.de...
  • Page 3 20. Warranty/Guarantee/Customer Service 4.4 Safety instructions for circular saw blades 21. EC Declaration of Conformity 4.5 Residual risks and protective measures 22. Components WS 700T, WS 700T-230 4.6 Behavior in an emergency 5. Used warning and information symbols 6. Part designation 7.
  • Page 4 1. Foreword 1.3 Designation of machine machine Designation replaced Trade name of the item to which this operating manual refers - see cover page. Before assembly and before commissioning, read the entire text of the operating instructions. Use these instructions to familiarize yourself with 1.4 Copyright the machine, its correct use and the All documents are protected by copyright.
  • Page 5 The machine is a firewood processing machine with which you can cut firewood on a rocker. The machine – tilting saw WS 700T and WS 700T-230 – is only suitable for sawing wood with a diameter of 5 – 25 cm and a length of 30 The machine is powered by an electric motor.
  • Page 6 4. Security 3. Environment Please recycle waste and do not This section provides a comprehensive dispose of it as garbage. All tools, overview of all important safety aspects for hoses and packaging must be adequate protection of the operator as well as sorted, taken to the local recycling for safe and trouble-free operation.
  • Page 7 4.2 Safety instructions and endanger other persons through improper use. First-time users should seek instruction from WARNING! the seller to familiarize themselves with the Familiarize yourself with the machine. characteristics of the machine, its intended use Proper training is a prerequisite for working and the necessary safety devices.
  • Page 8 Carry out all work calmly and carefully. must be switched off. Never leave the machine running unattended. Only use original LUMAG spare parts and accessories. The use of other spare parts and accessories increases the risk of accidents. We CAUTION! accept no liability for any resulting damage.
  • Page 9 4.3 Personal protective equipment (PPE) 4.5 Residual risks and protective measures When handling the machine, it is essential to wear personal protective equipment (PPE) to minimize risks to the operator. The following WARNING! protective measures must be observed: Disabling, modifying, blocking, dismantling, converting or attaching any parts to the machine's safety and protective devices is –...
  • Page 10 Electrical Residual Hazards 4.6 Behavior in an emergency Direct or indirect electrical contact Touching If an accident occurs, initiate the necessary first live parts when electrical components are open aid measures and request qualified medical or defective or when electrical connections are assistance as quickly as possible.
  • Page 11 5. Warning and information Warning of dangerous electrical symbols used voltage (model WS 700T). Symbols are provided on the machine to provide important information about the Warning of dangerous electrical product and instructions for use. voltage (model WS 700T-230). DANGER! This is about your safety.The...
  • Page 12 Additional fuse for the saw blade return spring 14 saw blade guard rocker latch 15 rocker extension 16 length stop transport wheels Locking pin for the saw blade Switch-plug combination with motor protection 400 V (Mod. WS 700T) or 230 V (Mod. WS 700T-230)
  • Page 13 7.1.1 Three-phase motor (mod. WS 700T) 250 mm Max. round wood diameter The WS 700T reciprocating saw may only be 300~ 1000 mm length of wood connected to a 400 volt mains supply with 50 Hz and noise warning** 16 A fuse via the 5-pin mains connection cable.
  • Page 14 7.1.2 AC motor (Mod. WS 700T-230) possible transport damage The WS 700T-230 reciprocating saw may only be connected to a 230 volt mains supply with 50 Hz and Report any complaints to the dealer or 16 A fuse via the 3-pole mains connection cable.
  • Page 15 9. Assembly 9.2 Installing the rocker extension Insert the rocker extension (15) into the recess Only a few steps need to be taken to make of the feed rocker as shown and fix it with the the machine ready for use. star grip (X).
  • Page 16 10. Operation working position 1. Lift the rocker latch (6) and swing the rocker outwards. 10.1 Rocker lock transport position 1. Press the feed rocker (4) towards the motor until the rocker touches the end stop (11). 2. Snap the rocker latch (6) into the frame to secure the rocker.
  • Page 17 11. Transport and storage 10.3 Length stop The required log lengths can be easily determined using the marking on the length For easier transport over short distances, the stop (16) and the end edge. machine is equipped with two wheels and a handle (3).
  • Page 18 12th lineup CAUTION! The machine must never be transported when loaded. WARNING! Only operate the machine when it is in a stable position! Turn off Place one foot on the axle and carefully put the Organize your workspace. Plan work in saw down.
  • Page 19 13. Commissioning IMPORTANT NOTE! The machine must not be set up on a The wrong direction of rotation of the motor will sloping surface. Particular care must be cause damage to the hydraulic pump. taken to ensure that the floor does not give way under the weight of the machine.See…...
  • Page 20 14th work process Have a minimum cable cross-section of 2.5 mm². In addition, the cable extension should not exceed 20 m and also have a cable cross- section of at least 2.5 mm². The cable extension must be completely unrolled. WARNING! with The machine may only be operated via a mains...
  • Page 21 4. Hold the rocker with both hands on the handles of 14.3 Switching off the machine (end of work) the protective cover (2) and the rocker (3) and drive by electric motor guide them evenly towards the saw blade and saw Press the red OFF button.
  • Page 22 15. Control work 15.4 Saw blade Check that the saw blade is firmly seated before each use! The saw blade is a wearing part. Check the saw blade for wear and damage before each use Before carrying out any inspection work on the machine: and sharpen or replace if necessary.
  • Page 23 16.2 Sharpening the saw blade protective devices after maintenance work. Saw blades should only be resharpened by a specialist company to achieve optimal Only use original LUMAG spare parts. Other sharpness. parts can cause unforeseeable damage and injuries. 16.3 Changing the saw blade Bring the feed rocker (4) into working position.
  • Page 24 2. Remove the M5 lock nut and washers from the saw blade guard (13/14) … Fig. 19_Changing the saw blade / Step 4‐6 7. Loosen the M12x30 clamping nut using the wrench provided. Remove the washer and clamping flange and pull off the saw blade. Fig.
  • Page 25 17. Disposal 16.4 Cleaning Clean the machine regularly to ensure optimal When the machine is no longer serviceable and functioning. is to be scrapped, it must be deactivated and Remove all foreign objects and other materials dismantled, that is, it must be brought to a that have accumulated on the saw blade and condition where it can no longer be used for the machine.
  • Page 26 18. Circuit diagram Fig. 21_Circuit diagram 400 V Fig. 22_Circuit diagram 230 V WARNING! Connections and repairs to the electrical equipment may only be carried out by a qualified electrician.
  • Page 27 WARNING! Any faults in the machine or engine that require major intervention should always be repaired by your LUMAG specialist workshop or an authorized specialist workshop. Improper intervention will void the warranty. The following table lists possible malfunctions and how to remedy them. Safety regulations must be observed during all repair, setup, maintenance and cleaning work.
  • Page 28 The guarantee for parts, our service team is available as follows: LUMAG products is 24 months for exclusively private use, and 12 months for commercial or Service time: Monday to Thursday from 7:30 a.m.
  • Page 29 Christopher Weißenhorner Kirchdorf a. Inn, October 28, 2024 Signature Place, date (Managing Director) Manufacturer: LUMAG GmbH Rudolf-Diesel-Straße 1a, D-84375 Kirchdorf a. Inn Storage of documents: LUMAG GmbH, Rudolf-Diesel-Straße 1a, D-84375 Kirchdorf a. Inn C. Weißenhorner, Management...
  • Page 30 22. Components WS 700T, WS 700T‐230 WARNING! All repairs to the machine must be carried out by authorized personnel. Any necessary electrical work should only be carried out by an authorized specialist.
  • Page 32 Subject to change! Version WS700T, WS700T230 A (10.24 de) LUMAG specialist dealer can be found at: www.lumag-maschinen.de LUMAG GmbH Rudolf-Diesel-Str. 1a D-84375 Kirchdorf a.Inn Germany Internet:www.lumag-maschinen.de...

This manual is also suitable for:

Ws 700t-2306566565666Gamul w5