Related Manuals for Lumag RP-1100PRO
Summary of Contents for Lumag RP-1100PRO
- Page 1 Translated from German to English - www.onlinedoctranslator.com RP-1100PRO Art. No.: RP1100PRO operating instructions vibrating plate www.lumag-maschinen.com...
- Page 2 IMPORTANT INSTRUCTIONS DANGER!Before assembly and before commissioning, read the entire text of the operating instructions. Use these instructions to familiarize yourself with the device, its correct use and the safety instructions. A NOTICE According to the applicable product liability law, the manufacturer of this device is not liable for damages caused to or by this device in the following cases: - improper handling,...
- Page 3 RP-1100PRO...
- Page 6 10-15 mm...
- Page 7 CONTENTS CONTENTS 1. Introduction 2. Intended use 3. Safety instructions . 1 Operational safety . Safety when using combustion engines . Service security 3.4 Warning and information symbols used 4. Controls 5. Machine transport 5.1 Mechanical lifting 5.2 Moving the machine on the ground .
- Page 8 INTENDED USE SAFETY INSTRUCTIONS 1. INTRODUCTION This manual contains information and procedures for the safe operation and maintenance of this model. For your own safety and to prevent injury, carefully read, understand, and follow the safety instructions in this manual at all times. 2.
- Page 9 SAFETY INSTRUCTIONS 3.1 Operational safety WARNING Familiarize yourself with the machine. Proper training is a prerequisite for working safely with this machine. Incorrect operation or operation by untrained personnel can be dangerous. Read the operating instructions for this machine and the engine manual carefully and familiarize yourself with the controls.
- Page 10 SAFETY INSTRUCTIONS • ALWAYSRead the operating instructions before operating the appliance. Instructions on hazards, warnings and precautions must be strictly observed to minimize the risk of personal injury, property damage and incorrect servicing. 3.2 Safety when using combustion engines DANGER Internal combustion engines pose a particular danger during operation and when refueling.
- Page 11 SYMBOLS USED substitute. • The stickers on the machine warn of dangers. The machineALWAYSKeep clean and replace damaged stickers if necessary. 3.4 Warning and information symbols used A NOTICE The machine is delivered without engine oil. The first thing to do before using it for the first time is to fill it with engine oil.
- Page 12 SYMBOLS USED CONTROLS CAUTION! * lifting point / binding point THROTTLE LEVER Turtle means SLOW or IDLE Rabbit means FULL SPEED or FAST MAX. MIN. NAMEPLATE Equipped with model name, year of manufacture and serial number. Please always state this information when ordering spare parts or for service information.
- Page 13 MACHINE TRANSPORT oil filler cap / dipstick air filter cover paper filter insert foam filter insert seal radial seal heel cup spark plug wrench throttle stop screw 5. MACHINE TRANSPORT WARNING Before transporting the machine or storing it indoors, allow the engine to cool down to avoid burns and the risk of fire.
- Page 14 MACHINE TRANSPORT ASSEMBLY 5.2 Moving the machine on the ground • The transport trolley makes handling easier. By rocking/pushing the machine forwards on the guide bar - with the help of one person - the trolley can be hooked into the base plate.
- Page 15 ASSEMBLY 6.2 Assembly - throttle cable assembly step 1 assembly step 2 Attach the throttle lever to any side of Loosen the wing screw (A) on the air filter the handlebar. housing and remove the cover. assembly step 3 assembly step 4 Loosen all screws and remove the bottom of Loosen the wing screw (B) on the air filter the air filter housing.
- Page 16 COMMISSIONING 7. COMMISSIONING DANGER Read the safety instructions carefully (see “Safety instructions”). 7.1 Recommended fuel This engine requires only regular unleaded gasoline with a research octane rating of 91 or higher. Use only fresh, clean fuel. Water or impurities in the gasoline will damage the fuel system.
- Page 17 COMMISSIONING 7.3 Starting the engine (Fig. 5 – 10) • Slide the fuel tap (5) to the right to open it. • When cold, move the choke lever (4) to the left to “CLOSE”. • When warm, leave the choke lever (4) set to the right to “OPEN”. •...
- Page 18 COMMISSIONING MAINTENANCE A NOTICE Do not use the plate compactor on concrete or hard or tightly compacted ground surfaces. In such cases, the device will begin to impact instead of vibrating, causing damage to the plate and the motor. shaking with rubber mat By placing a rubber mat under the vibrating plate, you can prevent damage to slabs and natural stones during vibrating.
- Page 19 MAINTENANCE 8.1 Maintenance plan Please carry out and adhere to these maintenance tasks regularly to avoid damage and to ensure that the safety devices function properly. Failure to do so may result in an accident! Each After All 2 Every Daily weeks month or...
- Page 20 MAINTENANCE 8.2 Oil change oil level check (Fig. 14) Check the engine oil level with the engine stopped and level. • Remove the oil filler cap/dipstick (13) and wipe clean. • Reinsert the dipstick into the oil filler neck without screwing it in, then remove it to check the oil level.
- Page 21 MAINTENANCE Check for damage. Replace damaged inserts. • Clean the foam filter insert (16) in warm water and a mild soap solution. Rinse thoroughly with clean water and allow to dry well. WARNING NEVER use gasoline or low flash point cleaning solvents to clean the air cleaner element. A fire or explosion could result.
- Page 22 MAINTENANCE A NOTICE A loose spark plug can overheat and damage the engine. And over-tightening the spark plug can damage the threads in the cylinder head. 8.6 Adjusting the engine speed (Fig. 19) A NOTICE Operating the disk at a higher speed than recommended in the "Technical Data" may cause disk and motor damage.
- Page 23 MAINTENANCE 8.8 Lubrication of the exciter (Fig. 21) Check oil level: Check the oil level in the exciter every 0 hours of operation. • Place the plate horizontally. • Remove the belt guard (B) and remove the drive belt (see section Adjusting the Drive Belt).
- Page 24 TROUBLESHOOTING 9. TROUBLESHOOTING Caused remedy Disturbance Gas regulation incorrectly Install gas regulation correctly. installed. Ground is too wet, the plate Allow drying time. Pre-feed speed is too low. The gets stuck. disk does not reach maximum Drive belt too loose, slips on Adjust or replace drive belt.
- Page 25 TECHNICAL DATA 10. TECHNICAL DATA Model: RP-1100PRO drive motor: 1-cylinder 4-stroke OHV petrol engine Rated power: Engine speed: 1/min Fuel: unleaded regular gasoline Fuel tank capacity: SAE 10W- 0 or 10W- 0 Engine oil: ~ 0, Engine oil content: F TC or other equivalent spark...
- Page 26 WARRANTY / CUSTOMER SERVICE 11. WARRANTY / CUSTOMER SERVICE warranty The statutory warranty period is years after the date of purchase. In case of any If there are any defects in the product, please contact our customer service directly. For this purpose, we recommend that you carefully keep your purchase receipt.
- Page 27 Fax: 0049 / (0)8571 / 92 556-19 that the product vibrating plate (compaction machine) Device type: RP-1100PRO Device type: meets the essential protection requirements of the above-mentioned EC directives. Conformity is based on the following standards: 00-1: 00 00- : 00 ZEK 01.01-08/06.08...
- Page 28 COMPONENTS OF THE MACHINE 13. COMPONENTS OF THE MACHINE...
- Page 29 COMPONENTS OF THE MACHINE pathogens...
- Page 30 ACCESORIES 14. ACCESSORIES Designation Description Order No. rubber mat, GRP110 00 01 575 / 440 / 8 mm black 00 0 Ø 9 mm RRP110 wheelset...
- Page 32 LVG Hartham GmbH Robert-Bosch-Ring 3 D-84375 Kirchdorf am Inn Phone: + 49 (0)85 71 / 92 556 - 0 Fax: + 49 (0)85 71 / 92 556 - 19...
Need help?
Do you have a question about the RP-1100PRO and is the answer not in the manual?
Questions and answers