Advertisement
Quick Links
Advertisement
Related Manuals for Keysight 11683AZ-K01
Summary of Contents for Keysight 11683AZ-K01
- Page 1 11683AZ Option K01 and K02 Power Meter Range Calibrator Installation Note...
- Page 2 Declarations of Conformity for this product ceed beyond a CAUTION notice until the indi- the DFARS and are set forth specifically in and for other Keysight products may be down- cated conditions are fully understood and met. writing elsewhere in the EULA. Keysight shall loaded from the Web.
- Page 3 ........... . . 17 Keysight 11683AZ Option K01 and K02 Installation Note...
- Page 4 THIS PAGE HAS BEEN INTENTIONALLY LEFT BLANK. Keysight 11683AZ Option K01 and K02 Installation Note...
- Page 5 11683AZ Option K01 and K02 ....12 Figure 1-2 Range Switch/Sampling Gate Schematic Diagram . .18 Keysight 11683AZ Option K01 and K02 Installation Note...
- Page 6 THIS PAGE HAS BEEN INTENTIONALLY LEFT BLANK. Keysight 11683AZ Option K01 and K02 Installation Note...
- Page 7 ........17 Keysight 11683AZ Option K01 and K02 Installation Note...
- Page 8 THIS PAGE HAS BEEN INTENTIONALLY LEFT BLANK. Keysight 11683AZ Option K01 and K02 Installation Note...
- Page 9 Keysight 11683AZ Option K01 and K02 Power Meter Range Calibrator Installation Note Special Supplement Description Assembly Process Operation Performance Test...
- Page 10 Special Supplement Description The 11683AZ-K01/11683AZ-K02 is a Field Upgrade of a standard 11683A range calibrator to 11683AZ-H01. This kit is used to modify the unit so that it operates with either the Internal DC-Reference source, or an external programmable DC-Reference source.
- Page 11 50 mm Blue Wire 2950-0043 2190-0016 Washer 11683-00011 Ground Connector 8150-0451 130 mm Yellow Wire 8150-0454 200 mm Violet Wire 11683-00005 Xmer Mounting Bracket 11683-60004 Power Switch Assembly 2360-0115 Screw 2420-0001 Hexagonal Nut 11683-20008 Insulator Keysight 11683AZ Option K01 and K02 Installation Note...
- Page 12 6 Remove resistor (196K?) that is between yellow and violet wire (8150-0454) from multi-position switch (11683-60005) 7 Keep violet wire (8150-0454) on multi-position switch (11683-60005) but remove yellow wire (8150-0451) from multi-position switch (11683-60005) for next step. Keysight 11683AZ Option K01 and K02 Installation Note...
- Page 13 20 Solder black wire (8150-0447) from bottom BNC lug (0360-1190) to 31.62K resistor on multi-position switch (11683-60005). 21 Ensure yellow wire from middle of SPDT switch (3101-0163) to the feed through going to the power sensor housing was solder. Keysight 11683AZ Option K01 and K02 Installation Note...
- Page 14 The above calculated voltages for range 100 mW to 300 W are based on the table shown in the 11683A Operating and Service Manual (11683-90014). The remaining voltages are based in the Keysight 11683AZ Option K01 and K02 Installation Note...
- Page 15 4 Connect the jumper between the DC REF INPUT BNC wire and the RANGE switch wire using an alligator test clip. 5 Set the REF SELECT switch to EXT. 6 Connect the 11683AZ-H01 Range Calibrator to the power line and turn it ON. Keysight 11683AZ Option K01 and K02 Installation Note...
- Page 16 10 Disconnect the 4-wire cable and jumper from the 11683A. This concludes the external DC-reference circuit performance test. If any of the voltage or resistance readings are incorrect, refer to the troubleshooting information in the 11683A Operating and Service Manual (11683-90014). Keysight 11683AZ Option K01 and K02 Installation Note...
- Page 17 11683-20008 Insulator In other words, the 11683AZ Option H01 is similar to the standard 11683A and the information in the Operating and Service Manual for the standard 11683A applies to this instrument. Keysight 11683AZ Option K01 and K02 Installation Note...
- Page 18 Special Supplement Figure 1-2 Range Switch/Sampling Gate Schematic Diagram Keysight 11683AZ Option K01 and K02 Installation Note...
- Page 19 This information is subject to change without notice. Always refer to the English version at the Keysight website for the latest revision. © Keysight Technologies 2004-2022 Edition 3, June 25, 2024 Printed in Malaysia *11683-90017* 11683-90017 www.keysight.com...
Need help?
Do you have a question about the 11683AZ-K01 and is the answer not in the manual?
Questions and answers