Advertisement
Quick Links
Advertisement
Related Manuals for Keysight 16048D
Summary of Contents for Keysight 16048D
- Page 1 Keysight 16048D Test Leads Operation and Service Manual...
- Page 2 EULA. governed by United States and Declaration of Conformity Keysight shall be under no obligation international copyright laws. to update, revise or otherwise modify Trademark Acknowledgments Declarations of Conformity for this the Software.
-
Page 3: Table Of Contents
Maintenance ............. . 10 Keysight 16048A Test Leads... - Page 4 Contents Keysight 16048A Test Leads...
-
Page 5: Operation
BNC (m) terminated-coaxial test leads. These test leads are used to attach user-fabricated test fixtures. DC bias levels of up to ±42V can be applied to the 16048D. Cable length is 2 meter. The 16048D is shown in Figure 1-1. -
Page 6: Specification
POLLUTION DEGREE 2 INDOOR USE Compensation for Fixture Residual Impedance Error The 16048D has inherent stray capacitance, residual inductance, and residual resistance that affect the accuracy of measured values. To compensate for, or negate, these residuals to minimize measurement error, the instrument’s Open/Short compensation procedure should be performed. -
Page 7: Operation
Operation Operation Setup and measurement procedure is as follows: 1. Connect the 16048D directly to the UNKNOWN terminals of the instrument. 2. Connect the user-fabricated test fixture to the test leads. 3. Perform Open/Short compensation as described in the instrument’s operation manual. - Page 8 Operation Operation Keysight 16048D Test Leads...
-
Page 9: Service
Keysight 16048D Test Leads Operation and Service Manual Service Introduction This chapter gives the service information for the 16048D. Serial Number for Non-RoHS 16048D: “MY44100001 - MY44199999” or “SG44100001 - SG44199999” Serial Number for RoHS 16048D: “MY44200001 and above” or “SG44200001 and above”... -
Page 10: Maintenance
RoHS support part backward incompatible with non-RoHS 16048D. Special handling is needed while using the RoHS replacement part on non-RoHS 16048D. The original support part number is replaced by the respective “RoHS Compliant Replacement Part”. - Page 11 Service Maintenance Figure 2-1 Parts Identification Keysight 16048D Test Leads...
- Page 12 16047-40000 STOPPER (RoHS unit doesn’t have the stopper) 16048-04011 TOP COVER 16048-60620 TEST LEAD, COZXIAL CABLE 2360-0192 SCREW- 16048-60620 TEST LEAD, MACH 6-32 COZXIAL CABLE 1400-0719 CABLE TIE 1400-3284 CABLE TIE (1400-3284) GROMMET- GROMMET- Keysight 16048D Test Leads...
- Page 13 SCREW- SCREW- MACH Set Change: MACH 6-32 0515-0372 16032-10021 PLATE PLATE Set Change: 16032-10621 2190-0016 WASHER- 2190-0016 WASHER- LK INTL T LK INTL T 2950-0001 NUT-HEX 2950-0001 NUT-HEX 16032-10022 PLATE SHIELD PLATE SHIELD Set Change: 16032-10622 Keysight 16048D Test Leads...
- Page 14 Part Number Compliant Replacement Part 16032-60001 BNC BRACKET 16032-60071 CONNECTOR (30 thru 35) ASSEMBLY a. Replace all the associated parts marked with as they are mutually dependent. *. Parts marked with * are not separately replaceable. Keysight 16048D Test Leads...
- Page 15 This information is subject to change without notice. © Keysight Technologies 1990-2021 Edition 7, April 2021 *16048-90031* 16048-90031 www.keysight.com...
Need help?
Do you have a question about the 16048D and is the answer not in the manual?
Questions and answers