Autonics ARIO Series Product Manual

TCD210210AB
Slim Remote I/O
ARIO Series
PRODUCT MANUAL
For your safety, read and follow the considerations written in the instruction
manual, other manuals and Autonics website.
The specifications, dimensions, etc. are subject to change without notice for product
improvement. Some models may be discontinued without notice.
Features
• Industrial Ethernet/Fieldbus serial communication I/O for Smart Factory
• Multiple I/O distribution control using PLCs and industrial PCs.
• Coupler: available in 8 different communication protocols
- EtherCAT, CC-Link V1/V2, ProfiNet, ProfiBus, EtherNet/IP, DeviceNet,
Modbus TCP compatible, Modbus RTU compatible
• Module: various input/output modules, power module
- Bus power + Field power, Bus power/Field power, digital input/output (4/8/16
channels), analog input/output (2/4/8 channels), temperature input (4/8 channels)
- Expandable up to 64 modules (may vary by communication type)
• Hot-swap feature
: Terminal and body units can be removed/swapped during operation for easy
maintenance
• Push-in connection method: easy wire connection without requiring additional tools
• Easy module attachment and removal on DIN rails
• Comprehensive device management software DAQMaster for improved convenience
• Module settings, real-time control/monitoring/diagnosis of input/output signals
• Virtual mode allows simulation of product set up and offers set up recommendations
ᜢ ᜽ ᜨ ᜣ ᜫ
Safety Considerations
• Observe all 'Safety Considerations' for safe and proper operation to avoid hazards.
• ᜸ symbol indicates caution due to special circumstances in which hazards may occur.
᜸ Warning
Failure to follow instructions may result in serious injury or death.
01. Fail-safe device must be installed when using the unit with machinery that
may cause serious injury or substantial economic loss. (e.g., nuclear power
control, medical equipment, ships, vehicles, railways, aircraft, combustion
apparatus, safety equipment, crime/disaster prevention devices, etc.)
Failure to follow this instruction may result in personal injury, fire or economic loss.
02. Do not use the unit in the place where flammable/explosive/corrosive gas,
high humidity, direct sunlight, radiant heat, vibration, impact, or salinity
may be present.
Failure to follow this instruction may result in explosion or fire.
03. Do not disassemble or modify the unit.
Failure to follow this instruction may result in fire.
04. Do not connect, repair, or inspect the unit while connected to a power
source.
Failure to follow this instruction may result in fire.
05. Check 'Connections' before wiring.
Failure to follow this instruction may result in fire.
᜸ Caution
Failure to follow instructions may result in injury or product damage.
01. Use the unit within the rated specifications.
Failure to follow this instruction may result in fire or shortening the life cycle of the
product.
02. Use dry cloth to clean the unit, and do not use water or organic solvent.
Failure to follow this instruction may result in fire or electric shock.
03. When connecting the power input and output, use AWG 22-16 cable and
check the connecting method of crimp terminal.
Failure to follow this instruction may result in fire or malfunction due to contact
failure.
04. Keep the product away from metal chip, dust, and wire residue which flow
into the unit.
Failure to follow this instruction may result in fire or product damage.
05. Do not connect or disconnect connector (terminal) wire or power, when the
product is operating.
Failure to follow this instruction may result in fire or malfunction of the product.
Cautions during Use
• Follow instructions in 'Cautions during Use' .
Otherwise, It may cause unexpected accidents.
• BUS power and I/O power should be insulated by the individually insulated power
device.
• Power supply should be insulated and limited voltage/current or Class 2, SELV power
supply device.
• Keep away from high voltage lines or power lines to prevent inductive noise.
In case of installing power line and input signal line closely, use line filter or varistor at
power line and shielded wire at input signal line. For stable operation, use shield wire
and ferrite core, when wiring communication wire, power wire, or signal wire.
• Do not use near the equipment which generates strong magnetic force or high
frequency noise.
• Use the rated standard cables and connectors. Do not apply excessive power when
connecting or disconnecting the connectors of the product.
• Do not touch the module communication connector part of the base.
• Do not connect, or remove the base while connected to a power source.
For removing the terminal, body or base, do not operate units for a long time without it.
• This unit may be used in the following environments.
- Indoors (in the environment condition rated in 'Specifications')
- Altitude max. 2,000 m
- Pollution degree 2
- Installation category II