Related Manuals for BAFANG DP C360.CAN
Summary of Contents for BAFANG DP C360.CAN
-
Page 1: Table Of Contents
7 USER MANUAL FOR DP C360.CAN CONTENT 7.1 Important Notice 7.6.2 Selection of Assistance Levels 7.2 Introduction of Display 7.6.3 Selection of Mode 7.3 Product Description 7.6.4 Headlights / Backlighting 7.3.1 Specifications 7.6.5 Walk Assistance 7.3.2 Functional Overview 7.6.6 Battery Capacity Indication 7.4 Display Information... -
Page 2: Important Notice
• Do not clean the display with a steam jet, high-pressure cleaner or water hose. 7.2 INTRODUCTION OF DISPLAY • Model: DP C360.CAN • The label marking is as follow: • The housing material is PC in black, the window is made from high hardness acrylic,... -
Page 3: Product Description
7.3 PRODUCT DESCRIPTION 7.3.2 Functional Overview 7.3.1 Specifications • CANBUS communication protocol, three • Operating temperature: -20℃~45℃ buttons facilitate operation • Storage temperature: -20℃~60℃ • Speed indication (including the real-time • Waterproof: IP65 speed) • Bearing humidity: 30%-70% RH • Unit switching between km and mile •... -
Page 4: Key Definition
7.5 KEY DEFINITION System On/Off Down BF-UM-C-DP C360-EN November 2019... -
Page 5: Normal Operation
7.6 NORMAL OPERATION 7.6.1 Switching the System ON/OFF Press and hold (>2S) on the display to turn on the system. Press and hold (>2S) again to turn off the system. If there is no operation within 5 minutes, the display will automatically be turned off. (The automatic shutdown time can be set by customer's requirement between 1 and 15 minutes.) 7.6.2 Selection of Assistance Levels When the display is turned on, briefly press the... -
Page 6: Walk Assistance
7.6.5 Walk Assistance Briefly press the (<0.5S) button until the gear of "P" is displayed. At this point, press and hold (>2S) button, the Pedelec enters the walk assistance mode. The indicator will flash and the speed indicator will show the speed in real-time. If release the button, the system will stop the state of walk assistance and the indicator goes out. -
Page 7: Settings
7.7 SETTINGS 7.7.1 Setting default value is "Km". 1) After the display is turned on, press and hold the (>2S) button, to access the setting interface. 7.7.1.3 Brightness of Backlighting "bL1" is displayed on the position of speed indicator, you can press the button to adjust the brightness of backlight- 2) If no operation within 10 seconds under ing with 5 levels. -
Page 8: Information
button (<0.3S) to enter speed limit interface. 2) Battery's Absolute Percentage 7.7.2 Information "b1 0" is displayed on the position of speed 7.7.2.1 Speed Limit indicator, and the value of "battery's abso- lute percentage" is displayed on the position "SP L"is displayed on the position of speed of mileage indicator. - Page 9 5) Battery's Last Uncharged Time press the button (<0.3S) to enter the interface of battery's temperature. "b1 3" is displayed on the position of speed indicator, and the value of "battery's last uncharged time" is displayed on the position of mileage indicator.(Unit: h) After viewing, press the button (<0.3S) to enter the interface of battery's cycle index.
-
Page 10: Controller Information
software check. 7.7.2.6 Battery Information 7.7.2.5 Controller Information 1) Battery Hardware Check 1) Controller Hardware Check "bH c" is displayed on the position of "CH c" is displayed on the position of speed speed indicator, and the last three digits indicator, and the last three digits (containing the decimal point) of "battery (containing the decimal point 00.0) of... -
Page 11: Error Code Definition
7.8 ERROR CODE DEFINITION The HMI can show the faults of Pedelec. When a fault is detected, the indicator " " lights up and the error code will be shown on the position of speed indication. Note: Please read carefully the description of the error code. When the error code appears, please first restart the system.
Need help?
Do you have a question about the DP C360.CAN and is the answer not in the manual?
Questions and answers