SawStop CNS175-PFA30 Assembly Instructions

Before assembling your saw, make sure that you
have all the components identified on pages 14 and
15 in the Owner's Manual, including hardware
pack #1 and hardware pack #2. Call the SawStop
Service Department at 503-582-9934 if any
components are missing. Hardware pack #2
includes some of the tools needed to assemble
the saw. You will also need the following additional
tools:
1. an 8 mm socket
2. a 10 mm wrench
3. two 13 mm wrenches
4. a level or straight edge
• Assemble the rear of the stand by attaching the remaining two
legs marked to the rear panel marked
A
legs are in front of the rear panel. Bumps on the legs fit into holes
in the rear panel to align the legs. Attach the legs to the rear
panel using four M8 x 20 carriage bolts
1
four M8 lock washers , and four M8 hex nuts
3
tighten the nuts at this time.
4
3
2
1
3
A
• Attach one of the short brackets marked
front legs. Make sure the legs are in front of the bracket. Use
two M8 x 20 carriage bolts , two M8 washers
1
washers , and two M8 hex nuts . Do not fully tighten the
3 4
nuts. Repeat this process to attach
the remaining short bracket
E
between the rear legs.
E
6
1
• Attach a foot to the bottom of
5
each leg by threading an M8 hex
nut on each foot and then
4
placing an M8 washer over
2
the nut. Insert a foot into the hole
at the base of each leg and then
place a second M8 washer and
2
thread a second M8 hex nut
4
onto each foot. Do not fully 4
tighten the nuts. The stand is
now fully assembled.
2
2
Note: If you purchased an optional
4
mobile base for your saw, install it
now by following the instructions
that came with the mobile base.
9
5
SawStop Service Department
503-582-9934
www.sawstop.com
© SawStop, LLC
Assembling Your SawStop Contractor Saw
Assembling the Stand
• Locate the stand components labeled
hardware pack #1. All of the hardware needed to assemble the
stand is located in the area with the blue background on
hardware pack #1. In order to easily identify the hardware used
in each of the following steps, the different pieces of hardware
are numbered on the hardware pack and on these assembly
instructions.
1
• Attach one of the side panels marked
. Make sure that the rear portions of the stand. Make sure the legs are in front of the
C
side panel and that the side panel is under the top flanges of the
front and rear panels. Bumps on the legs fit into holes in the side
, four M8 washers , panel to align the legs. Use four M8 x 20 carriage bolts
2
. Do not fully
four M8 washers
4
nuts to attach the side panel to the front and rear portions.
4
Do not fully tighten the nuts.
C
A
4
between the two
E • Attach one long bracket marked
right side of the stand. Make sure the legs are in front of the
, two M8 lock
2 brackets. Use two M8 x 20 carriage bolts
two M8 lock washers
long bracket. Do not fully tighten the nuts. Repeat this process
to attach the remaining long bracket
left side of the stand.
7
4
3
2
10
• Remove the saw from the box and locate the
mounting hardware. All of the hardware needed to
mount the saw to the stand is located in the area with
the yellow background on hardware pack #1.
through
A F
Hardware Pack 1
#
Assembling the Stand
Hardware for Steps 1-9
Hex Nuts, M8
(32 + 2 extra) 4
Carriage Bolts, M8 x 20
(24 + 2 extra) 1
Washers, M8 Leveling Feet
(32 + 2 extra) 2 5
(4)
Lock Washers, M8
3
(24 + 2 extra)
Mounting the Saw to the Stand
Hardware for Steps 10-14
Lock Washers,
8
M8 (4)
Hex Screws, Washers,
7
6 M8 (8)
M8 x 20 (4)
Hex Nuts,
9
M8 (4)
between the front and
D
, four M8 lock washers , and four M8 hex
2
3
1
4
3
2
between the legs on the
F
, two M8 washers
1
, and two M8 hex nuts to attach the
3 4
between the legs on the
F
3
4
2
1
Mounting the Saw
to the Stand
Hardware Pack
Assembling the Stand
Carriage Bolts, M8 x 20
1
(24 + 2 extra)
Washers, M8
(32 + 2 extra) 2
Lock Washers, M8
(24 + 2 extra) 3
Mounting the Saw to the Stand
Hardware for Steps 10-14
Hex Screws,
6 M8 x 20 (4)
• Assemble the front of the stand by attaching two of the legs
marked to the front panel marked
A
are in front of the front panel. Bumps on the legs fit into holes in
the front panel to align the legs. Attach the legs to the front
panel using four M8 x 20 carriage bolts
and
four M8 lock washers
3
tighten the nuts at this time. Leaving the nuts loose will make it
easier to align holes as you assemble the rest of the stand.
4
3
2
2
A
• Repeat the prior step to attach the remaining side panel
marked to the opposite side of the stand.
D
2
,
1
1
D
D
5
• The front, rear and side panels have flanges that overlap to
define mounting holes through which you will bolt the saw to
,
2
the stand. There is one hole in each corner of the stand.
Adjust the panels until the holes align and then tighten all of
the nuts in the stand using a 13 mm wrench.
F 8
• With the help of an assistant, pick up the saw and carefully set it
on the assembled stand with the front of the saw above the front
panel of the stand. Align the mounting holes in the bottom corners
of the saw with the mounting holes in the top corners of the stand.
While moving the saw do not set it down in the upright position on
a solid surface because the dust shroud can be damaged.
Warning! The saw weighs approximately 140 pounds. Be careful
and use proper lifting technique to avoid injury.
1
#
Hardware for Steps 1-9
Hex Nuts, M8
4
(32 + 2 extra)
Leveling Feet
(4) 5
Lock Washers,
8
M8 (4)
Washers,
M8 (8) 7
Hex Nuts,
9
M8 (4)
11
. Make sure that the legs
B
, four M8 washers 2 ,
1
, and four M8 hex nuts . Do not fully
4
B
1 A
3 4
mounting holes
Flip to
Other
Side