Resetting The Microprocessor; Specifications; Remote Control Unit (Rc010Sr) - Marantz NR1601 User Manual

ENGLISH ENGLISH DEUTSCH DEUTSCH

Resetting the microprocessor

Perform this procedure if the display is abnormal or if operations cannot be performed.
When the microprocessor is reset, all the settings are reset to their default values.
Various setting details can be saved and reset on this device. If setting details are saved before returning
to the default values, after returning to the default settings, setting details can be returned to the same
values as before returning to the defaults.
To return all of the settings to the default values, perform steps 2 to 4 without performing step 1.
ON/STANDBY
1
When the power is ON, press and hold
After "MEMORY SAVING" is shown on the display, "COMPLETE"is shown to inform you that the
settings have been saved.
2
Turn off the power using ON/STANDBY
3
ON/STANDBY
Press while simultaneously pressing
4
Once the display starts flashing at intervals of about 1 second, release the two
buttons.
5
STATUS ENTER
Press and hold and
After "MEMORY LOAD" is shown on the display, "COMPLETE" is shown to inform you that the
settings have returned to those saved in step 1.
If in step 4 the display does not flash at intervals of about 1 second, start over from step 2.
74
FRANÇAIS FRANÇAIS ITALIANO ITALIANO
ENTER STATUS
RETURN
STATUS and ENTER for more than 3 seconds.
.
ENTER RETURN
and
for more than 3 seconds.
ESPAÑOL ESPAÑOL NEDERLANDS NEDERLANDS SVENSKA SVENSKA

Specifications

n Audio section
• Power amplifier
Rated output:
Output connectors:
• Analog
Input sensitivity/Input impedance:
Frequency response:
S/N:
n Video section
• Standard video connectors
Input/output level and impedance:
Frequency response:
• Color component video connector
Input/output level and impedance:
Frequency response:
. n Tuner section
Receiving Range:
Usable Sensitivity:
50 dB Quieting Sensitivity:
S/N (IHF-A):
Total harmonic Distortion (at 1 kHz):
n General
Power supply:
Power consumption:
Maximum external dimensions:
Weight:
n Remote control unit (RC010SR)
Batteries:
For purposes of improvement, specifications and design are subject to change without notice.
Front:
50 W + 50 W (8 Ω, 20 Hz – 20 kHz with 0.08 % T.H.D.)
75 W + 75 W (6 Ω, 1 kHz with 10 % T.H.D.)
Center:
50 W (8 Ω, 20 Hz – 20 kHz with 0.08 % T.H.D.)
75 W (6 Ω, 1 kHz with 10 % T.H.D.)
Surround:
50 W + 50 W (8 Ω, 20 Hz – 20 kHz with 0.08 % T.H.D.)
75 W + 75 W (6 Ω, 1 kHz with 10 % T.H.D.)
Surround Back:
50 W + 50 W (8 Ω, 20 Hz – 20 kHz with 0.08 % T.H.D.)
75 W + 75 W (6 Ω, 1 kHz with 10 % T.H.D.)
6 – 8 Ω
130 mV/50 kΩ
10 Hz – 100 kHz — ±3 dB (Source Direct mode)
98 dB (IHF–A weighted, Source Direct mode)
1 Vp-p, 75 Ω
5 Hz – 10 MHz — +1, –3 dB
Y (brightness) signal — 1 Vp-p, 75 Ω
P / C signal — 0.7 Vp-p, 75 Ω
B B
P / C signal — 0.7 Vp-p, 75 Ω
R R
5 Hz – 60 MHz — +0, –3 dB
[FM]
(Note: μV at 75 Ω, 0 dBf = 1 x 10 –15 W)
87.5 MHz – 107.9 MHz 520 kHz – 1710 kHz
1.2 μV (12.8 dBf) 18 μV
MONO 2.8 μV (20.2 dBf)
MONO 70 dB
STEREO 67 dB
MONO 0.7 %
STEREO 1.0 %
AC 120 V, 60 Hz
250 W
0.2 W (Standby)
3 W (CEC standby)
440 (W) x 105 (H) x 367 (D) mm
9.0 kg
R03/AAA Type (two batteries)
[AM]