cocccocc ICCCOCCCCIOO ICCEOOEO USE SCMSOE FEATURES SSOSDOTD ACCESSORIES TECHNICAL SPECIFICATIONS STANDARD PARTS OSSIND INSTDLDSTION • Location and Mounting ROTOR INSTDLDSNIDN USER INTLTFDSE DTT DISPLAY 10. DPETDTITN THE CENTRIFUGE SWITCH ON THE CENTRIFUGE SPEED SETTING TIME SETTING • ACC/DCC • QUICK SPIN ROTOR START &...
1. INNNNNNNNION This centrifuge is equipped with a maintenance free drive, a large display & simple interface for efficient operation for daily lab usage. The programmable centrifuge can deliver up to 4500 RPM and can accommodates different types of rotors. lt features various programmable mode to save time &...
6. TECHNICALSPECIFICATIONS Motor Type Brushless DC Motor Max capacity 360ml (24 x 15ml) Max. Speed 4 500 RPM Speed Accuracy & Speed Step ± 100 RPM Run Time 1 min to 99:59 mins & infinite mode Ace 9/dcc 9 mode, �...
Page 6
Swing out Rotor (PLASTIC) SR. NO. ROTOR TYPE RCF VALUE (xg) i.' ,. II• ';._ , , "-" 1 C ,_, i, 3315 04x50ml � i t ;,, · 3334 16x15ml 24x15ml 3220 32x6ml 3152 Adaptor 50ml. Adaplor 15ml. Adaptor 15ml.
7. STANDARD PARTS USTING 8. INSTALLATION The Laboratory centrifuge is supplied in packaging box. Open the box, remove the packaging and gently place the centrifuge out of the box. Before 1st time usage, open the centrifuge & ensure to remove all packaging from the rotor chamber. Please keep all packaging in safe storage for at least 2 years for warranty purpose.
Page 8
T-A ll en Key ------� To replace or install the rotor, take the rotor and load vertically onto the motor shaft. Place the rotor nut in the center hole of the rotor onto the motor shaft. Put T -Allen Key into the rotor nut and turn clockwise to tighten and counter clockwise to loosen the rotor.
9. USER INTERFACE & DISPLAY ® gg:s� J LJSDD 0 RPM 0 RCF �,o LIDO ® r.'\ '-:V ® & ltem Button Name Function Single press, mo to r wi ll start as per selecte d r p m a n d Start time if lid clo se d.
L ED s for LID open close indication, Run indication, RPM & RCF functions. Display Element: 4 digit 7 segment 10. OPERATING THE CENTRIFUGE EWITCC ON THE CENTRIFUGE After connecting the power cord. Switch ON the main power supply & then Switch on the power switch located on the Rear side of the instrument.
• The timer in the centrifuge 's countdown timer in the display will be in "Min/Sec" mode. • Time will showed on after 5 sec. • Time indicate on Time LED light. • The input will be accepted if we leave the setting for display to blink 5 time. The value will blink 5 time to indicate acceptance.
deactivated, as it is factory fitted. OPENING CENTRIFUGE LID IN POWER FAILURE Disconnect the centrifuge from the main power supply. Wait until the rotor has come to a standstill (this may take langer time). Once the rotor has stopped, then pull the lid release thread located at the bottom left (to your right) of the machine This will open the centrifuge lid.
be cleaned carefully and properly before being used again. • Centrifuge may be used for the specified applications only. lt must not be operated in a hazardous or flammable environment and must not be used to centrifuge explosive or highly reactive substances. Also do not place the potential hazardous material within the clearance area/envelope.
• The brushless motor in the centrifuge requires no routine maintenance. Any required service should be performed by authorized, qualified personnel only. Repairs performed by unauthorized personnel may void the warranty. • Always keep the centrifuge housing, rotor chamber and rotor clean. All parts should be wiped down periodically with a soft cloth.
14. TROUBLESHOOTING This centrifuge has a seif - diagnostic function. lf a problem occurs, an error/warning code will be displayed on the display screen and the operator can determine the malfunction with the warning code below. ERROR PROBLEM SOLUTION No main power Power check &...
can lead to a reset, erasing last run memory. • lf motor gets hot due to which there will be fluctuation in speed value then allow centrifuge to get cool for atleast 30 minutes. Do not do any operation for 30 minutes. 15.
16. PRODUCT DISPOSAL Information on the disposal of electrical and electronic devices in the European Community The disposal of electrical devices is regulated within the European Community by national regulations based on EU Directive 2012 / 19 / EU on waste electrical and electronic equipment (WEEE).
Page 20
Swing Out Rotor Max. g-for c e/RCF: 3334 xg • Max. Rotation Speed: 4500 RPM Acceleration & Deceleration Time s35s Max. Load {adapter, lube holder, lube & contenls}: 16 X 161. 2 gm Rotor Weighl: 866. 4 gm Max. g force / Tube type Adapter type Holder...
Page 21
Fix Angle Rotor Max. g-force/RCF: 2766 X 9 Max. Rotation Speed: 4500 RPM Acceleration & Deceleration Time s35s Max. Load {adapter, lube holder, lube & contenls}: 32 X 154.2 gm Rotor Weighl: 1465.0gm Holder Max. g force / Tube type Adapter type Tubes / Type...
Need help?
Do you have a question about the iFUGE L400 NXT and is the answer not in the manual?
Questions and answers