Table of Contents
Advertisement
3. Working with the synth: List of functions in the G2 System menu
MIDI S
E
YS
X
Here you can set an 'Instrument SysEx ID'. This is very useful if
you're sending SysEx dumps of sounds from a sequencer to the
Nord Modular G2 and have several G2 synthesizers
Let's say you have two G2 synthesizers. These two instrument
models have the same 'Manufacturer ID' and 'Model ID' in the SysEx protocol. By defining separate
SysEx ID's on each of the two synths, you will be able to "direct" the SysEx dumps from the sequencer
to one of the G2's while the other one will ignore the dumps. Just make sure that you define a separate
SysEx ID before dumping the sounds to the sequencer. Select Instrument SysEx ID with the R
D
. Range: 1-16, All. See also
IAL
S
P
P
UST
ED
OL
Different sustain pedals use different polarity to activate the sustain
switch. Select between 'Open' and 'Closed' with the R
C
P
G
TRL
ED
AIN
Different control/expression pedals have different characteristics.
Here you can select Gain to adjust the control pedal functionality of
the synth to your specific expression pedal. Select range (x1.00-x1.50)
with the R
OTARY
M
P
EMORY
ROT
Select memory protection for the entire internal Patch and
Performance memory. Select On or Off with the R
K
Z
EYBOARD
ONE
Here you can set individual note ranges for each of the Slots in a
Performance. Press desired S
with the R
OTARY
set the highest note limit with the R
procedure for the other Slots by pressing the corresponding S
overlapping keyboard zones. Note that these ranges are also affected by any Keyboard Split setting you
have in your Performance (see
settings will be stored with it.
S
P
USTAIN
EDAL
Select if you want the Sustain Pedal functionality on or off in the
Patch. If set to On, a connected sustain pedal will control both
sustain and any parameters assigned to the Switch Morph group.
Select On or Off with the R
V
R
IBRATO
ATE
Select Vibrato Rate for the Patch. Range: 4.00-8.00 Hz. (The Vibrato
Amount is set in the Patch Settings "menu" for the Patch. See
"Editing Patch Settings" on page
S
YNTH NAME
Here you can name your synth. Select characters with the R
D
and change the "cursor" position with the left/right
IAL
N
buttons. Alternatively, press and hold the D
AVIGATOR
Page 32
ID |S
Y
"G2 MIDI System Exclusive Specification" on page
|S
Y
|S
Y
D
.
IAL
|S
Y
|P
E
button and set lower note limit
LOT
D
. Press the R
IAL
IGHT
OTARY
"Keyboard Split" on page
O
/O
|P
N
FF
A
D
OTARY
IAL
|P
A
34).
|S
Y
connected.
MIDI
D
OTARY
IAL
D
.
OTARY
IAL
N
button and
AVIGATOR
D
. Then, repeat the
IAL
LOT
49). When you store your Performance, these
.
OTARY
OWN
NORD MODULAR G2 V1.4x
MIDI SysEx ID |Sy
16
148.
Sust Ped Pol |Sy
.
Open
Ctrl Ped Gain |Sy
x1.00
Memory Prot
Off
Keyboard Zone |Pe
C-1 -
B3
buttons. It's also possible to have
Sustain Pedal |Pa
On
Vibrato Rate |Pa
6.02 Hz
Synth Name
ModularG2
OTARY
|Sy
|Sy
Advertisement
Table of Contents
