Table of Contents
Advertisement
NORD MODULAR G2 V1.4x
repeat the procedure for the other Slots by pressing the corresponding S
Performance Mode, the internal keyboard will send on all Slot's
MIDI G
C
LOB
Here you set the Global
Channel should be used for receiving
MIDI
control data (Modwheel, Aftertouch, Velocity, Aftertouch and
Pedals) if this data needs to be played by all Slots, no matter the
channel they are in. The Global
Program Change messages in Performance mode. Select Global
Range: Channel 1-16, Off. See also
MIDI C
S
LK
END
Here you choose whether or not to send out
jack of the synth. Sending out a
OUT
when you use the internal Master Clock as clock source. Select On or
Off with the R
OTARY
MIDI C
R
LK
ECV
Here you choose whether or not to accept external
signals received on the
set to 'On', the Master Clock of the G2 will automatically sync to any
incoming
Clock. Select On or Off with the R
MIDI
MIDI P
C
RG
HNG
Here you select how the synth should handle Program Change and
Bank Select (
MIDI CC
Receive (only) and Send and Receive with the R
MIDI C
|S
TRL
Here you select how the synth should handle
Select Off, Send (only), Receive (only) and Send and Receive with the
R
D
.
OTARY
IAL
MIDI S
C
END
This function lets you send the current values of all the
controllers that are used in a patch to the
the back of the G2. This function can be used to record all current
# values to one position in a song on a
MIDI CC
recording software. Note that it takes a little time to send all
MIDI
When the G2 is controlled by an external
is connected to the
current values of the knobs and sliders on the
a variation change is initiated from the G2 panel. Alternatively, the
programmed to send a SysEx command to the G2 to initiate this function each time a variation change
is initiated from the
Press the rightmost (Ins) Navigator button to start the transmission over the
function can also be activated by holding down S
3. Working with the synth: List of functions in the G2 System menu
|S
H
Y
Channel for the synth. The Global
MIDI
Channel should also be used for sending and receiving
MIDI
"MIDI Global Channel" on page
|S
Y
MIDI
D
.
IAL
|S
Y
connector at the back of the G2. If
MIDI IN
|S
Y
# 32)
messages. Select Off, Send (only),
MIDI
Y
|P
TRL
A
of the controller device, this function can be used to instantly refresh the
MIDI IN
controller device. See also
MIDI
MIDI
note data and
MIDI
MIDI
MIDI
Clock to the
MIDI
MIDI
Clock signal will only work
Clock
MIDI
D
.
OTARY
IAL
D
.
OTARY
IAL
# messages.
MIDI CC
#
MIDI CC
connector on
MIDI OUT
sequencer or
MIDI
controller device and the
MIDI
controller. Using this function is often necessary after
MIDI
"1.5 All Controllers Request" on page
and pressing the P
HIFT
buttons. Note that in
LOT
channels that have Keyboard Assign.
MIDI Glob Ch |Sy
16
Channel with the R
OTARY
142.
MIDI Clk Send |Sy
Off
MIDI Clk Recv |Sy
Off
MIDI Prg Chng |Sy
Send & Receive
MIDI Ctrl
Send & Receive
MIDI SendCtrl |Pa
Press > to send
# values.
MIDI CC
at the back of the G2
MIDI OUT
controller device can be
MIDI
connector. The
MIDI OUT
button (D
ATCH
MIDI
D
.
IAL
|Sy
149.
CC).
UMP
Page 31
Advertisement
Table of Contents
