Related Manuals for Wren ROBE UNIT L Corner
Summary of Contents for Wren ROBE UNIT L Corner
- Page 1 ROBE UNIT L Corner Robe Assembly Guide For Internal Use: FI.WR.INS.144_LCorner_Robe_AssemblyGuide_Rev3...
- Page 2 ROBE UNIT L Corner Robe Assembly Guide BEFORE YOU START THIS PRODUCT MUST BE SECURED TO THE WALL INSTALLATION SHOULD BE PERFORMED BY A COMPETENT PERSON ONLY. THIS PRODUCT COULD BE DANGEROUS IF INCORRECTLY INSTALLED Screws for fixing to walls are not provided as these vary depending on your wall material and construction.
- Page 3 ROBE UNIT L Corner Robe Assembly Guide CONTENTS Robe panels Components 4-19 Robe Assembly 11,17 Leg Attachment Hinge Plate Locations Secure Unit To Wall 22-23 Hanging Rail Locations Loose Shelf Fitting Hinge Adjustment INFINITY RANGE SPECIFIC INFORMATION - THE THIRD END PANEL THAT GOES AGAINST THE WALL WILL HAVE A PEBBLE OUTSIDE FACE.
- Page 4 ROBE UNIT L Corner Robe Assembly Guide Back Panel End Panels Back Panel (Ad) Bottom Fixed Shelf Bottom Fixed Shelf Top Fixed Shelf Top Fixed Shelf Rails Loose Shelf Pack (Ca) (Cb) (Cs) (Ct) Inc Fixings RAILS PROVIDED WITH THIS UNIT MAY DIFFER IN COLOUR TO THE REST OF THE UNIT For Internal Use: FI.WR.INS.144_LCorner_Robe_AssemblyGuide_Rev3 Page 2...
- Page 5 ROBE UNIT L Corner Robe Assembly Guide (L) x52 (K) x8 (P) x8 (W) x20 (F) x32 (H) x20 (LL) x9 15mm 30mm 45mm Cam Dowel Wooden Cam Lock 15mm Screw Screw Screw Dowel Cover Cap (N) x2 (T) x16 (U) x3 (FF) x6 (JJ)
- Page 6 ROBE UNIT L Corner Robe Assembly Guide Step 1. Seat dowels (F) into panels (Cb), (Ct) & (D) as shown. Seat 4 cam dowels (W) into panels (Cb) & (Ct) as shown. For Internal Use: FI.WR.INS.144_LCorner_Robe_AssemblyGuide_Rev3 Page 4...
- Page 7 ROBE UNIT L Corner Robe Assembly Guide Step 2. Seat cam dowels (W) into holes in end panels (B) as shown. Do not use power tools with cam dowel (W) or cam lock (H) For Internal Use: FI.WR.INS.144_LCorner_Robe_AssemblyGuide_Rev3 Page 5...
- Page 8 ROBE UNIT L Corner Robe Assembly Guide Step 3. Attach panels (Cb), (Ct) & (D) to end panels (B). Ensure (Cb) & (Ct) cam dowels (W) are facing in front of the end panels (B). All cam lock holes are to be positioned facing the INSIDE of the unit except rails (D), for ease of tightening.
- Page 9 ROBE UNIT L Corner Robe Assembly Guide Step 4. Insert cam locks (H). DO NOT tighten until Step 6. All cam lock holes are to be positioned facing the INSIDE of the unit except rails (D), for ease of tightening. For Internal Use: FI.WR.INS.144_LCorner_Robe_AssemblyGuide_Rev3 Page 7...
- Page 10 ROBE UNIT L Corner Robe Assembly Guide Step 5. Trim the edgeband covering the groove on the bottom of the end panels. Slide back panel (A) into the groove of end panels (B). Once back panel (A) is in position, ensure the panel is flush & square with bottom of end panels (B). For Internal Use: FI.WR.INS.144_LCorner_Robe_AssemblyGuide_Rev3 Page 8...
- Page 11 ROBE UNIT L Corner Robe Assembly Guide Step 6. Hand tighten all cam locks (H), this will tighten the unit together. Do not use power tools with cam dowel (W) or cam lock (H) Step 7. Ensure unit is square. Secure back panel (A) with 15mm screws (L) equally spaced at the top and bottom of back panel (A) into the fixed shelves (Ct) and (Cb) as shown.
- Page 12 ROBE UNIT L Corner Robe Assembly Guide Step 8. Secure back panel (A) using 16 x back panel clips (T). Slide the back panel clips (T) into the groove of both end panels (B). The back panel clips (T) should be evenly spaced as shown. Once in place, tighten screw. For Internal Use: FI.WR.INS.144_LCorner_Robe_AssemblyGuide_Rev3 Page 10...
- Page 13 ROBE UNIT L Corner Robe Assembly Guide Step 9. Position top and bottom section of legs as shown. Ensure legs are rotated to provide support to the unit (A). Secure with 2 x 15mm (L) screws per leg. Set all legs to the same height. It is important to lift unit (A) onto its legs.
- Page 14 ROBE UNIT L Corner Robe Assembly Guide Step 11. Seat dowels (F) into panels (Ca) & (Cs) as shown. For Internal Use: FI.WR.INS.144_LCorner_Robe_AssemblyGuide_Rev3 Page 12...
- Page 15 ROBE UNIT L Corner Robe Assembly Guide Step 12. Seat cam dowels (W) to the end panel (B) as shown. Do not use power tools with cam dowel (W) or cam lock (H) For Internal Use: FI.WR.INS.144_LCorner_Robe_AssemblyGuide_Rev3 Page 13...
- Page 16 ROBE UNIT L Corner Robe Assembly Guide Step 13. Attach panels (Ca), (Cs) & (Ad) to end panel (B) in positions as shown. Ensure panels (Ca) & (Cs) cam lock holes are facing INSIDE of the unit as shown. All cam locks (H) are to be positioned facing the inside of the unit, for ease of tightening. For Internal Use: FI.WR.INS.144_LCorner_Robe_AssemblyGuide_Rev3 Page 14...
- Page 17 ROBE UNIT L Corner Robe Assembly Guide Step 14. Insert cam locks (H). DO NOT tighten until Step 20. For Internal Use: FI.WR.INS.144_LCorner_Robe_AssemblyGuide_Rev3 Page 15...
- Page 18 ROBE UNIT L Corner Robe Assembly Guide Step 15. Ensure unit is square. Secure back panel (Ad) with 8 x 45mm screws (P) into fixed shelves (Ca) & (Cs)as shown. Step 16. Attach 6 x L brackets (FF) with 2 x 15mm screw (L) per L brackets equally spaced at the back panel (Ad).
- Page 19 ROBE UNIT L Corner Robe Assembly Guide Step 17. Position top and bottom section of legs as shown. Ensure legs are rotated to provide support to the end panels (B). Secure with 2 x 15mm screws (L) per leg. Set all legs to the same height. It is important to lift unit (B) onto its legs.
- Page 20 ROBE UNIT L Corner Robe Assembly Guide Step 19. Attach unit (B) to unit (A) as shown. Position the dowels in unit (B) into the holes in unit (A). Position the dowels in unit (A) into the holes in unit (B). For Internal Use: FI.WR.INS.144_LCorner_Robe_AssemblyGuide_Rev3 Page 18...
- Page 21 ROBE UNIT L Corner Robe Assembly Guide Step 20. Hand tighten all cam locks (H) on unit (B) top and bottom, this will tighten both units together. Cover all internal cam locks (H) with cover stickers large to conceal them. DO NOT use power tools with cam dowel (W) or cam lock (H) Step 21.
- Page 22 ROBE UNIT L Corner Robe Assembly Guide Step 23. (Where Required) Attach hinge plates onto both end panels (B) to suit as shown using 2 screws already in hinge plates. 2100 Robe 2006mm 1974mm INSIDE FACE 1201.5mm 1169.5mm 930.5mm 898.5mm 126mm 94mm From Bottom...
- Page 23 Step 24. Wren recommends securing the robe to the wall using rails (D). Drill pilot holes through back panel (A) and rails (D) into the wall. Screw through the pilot holes into the wall, place cover stickers small on the heads to conceal them.
- Page 24 ROBE UNIT L Corner Robe Assembly Guide Curved Hanging Rail. Attach hanging rail plates onto end panels (B) as shown using 2 x 15mm screws (L) provided per hanging plate. Measure 283.5mm in from the front edge, then measure down from the top fixed shelf using the measurements below and screw the hanging rail plate onto the end panel using the top hole.
- Page 25 ROBE UNIT L Corner Robe Assembly Guide Slide the centre support on to the curved hanging rail ensuring it is the correct orientation. Due to the doors overlapping one side of the hanging rail is longer than the other. 770mm Curved Hanging Rail Plan View Hanging Rail + 1 Loose Shelf...
- Page 26 ROBE UNIT L Corner Robe Assembly Guide Loose Shelves Secure shelf peg (JJ) to end panels (B) using 1 x 12.5mm screw (KK) per shelf peg. 6 x shelf pegs (JJ) are required per loose shelf. Shelf Peg Position the loose shelf onto shelf pegs (JJ) ensuring the spikes on the shelf pegs locate in the holes on the bottom of the loose shelf.
- Page 27 ROBE UNIT L Corner Robe Assembly Guide Hinge attachment and adjustment Insert hinges into frontal holes provided, secure with the 2 x screws and hinge dowels already located in the hinges. Attach the door to the unit, clip hinges onto the hinge plates and click to secure.
Need help?
Do you have a question about the ROBE UNIT L Corner and is the answer not in the manual?
Questions and answers