Related Manuals for Batca AXIS Free Trainer-S
Summary of Contents for Batca AXIS Free Trainer-S
- Page 1 Sept 2020 Free Trainer-S Owner’s Manual Serial Number Here Date of Purchase www.batcafitness.com AFTS Owner's Manual...
- Page 2 Instructions Congratulations on the purchase of your new Batca AXIS Free Trainer-S. This gym will provide you with a lifetime of enjoyment to meet your strength training needs. Batca Fitness Systems strives to build the best quality gyms and to package these gyms in such a way to avoid any damage during shipping.
-
Page 3: Accessories Provided
Tools Required For Free Trainer 3/4” Wrench • 9/16” Wrench/Ratchet • • 1/2” Wrench/Ratchet • Metric Allen Wrench Set (M8, M6, M4) • Tape Measure Accessories Provided Part # Description BFC-50136 Ankle Strap BFC-50132 Tricep Rope BFM-10682 Long Bar BFC-50126 Short Bar BFC-10103 4 Ring Strap Handle... - Page 4 Hardware Blister Packs Batca Fitness Systems AFTS Owner's Manual...
- Page 5 Add-on Hardware Blister Packs Enclosures Enclosures www.batcafitness.com AFTS Owner's Manual...
- Page 6 Add-on Hardware Blister Packs Batca Fitness Systems AFTS Owner's Manual...
- Page 7 BFM-52618 Anti-Deflection Plate BFM-11181 Lower Support Frame (User Left) BFM-11187 Pull Up Bar BFM-11097 Lower Cross-member with BATCA Logo BFP-51697 SHCS 3/8” x 1 1/2” BFM-11182 Upright Support W/Short Bar and Strap Storage BFP-51748 SHCS 3/8” x 3 1/4” BFM-11183...
- Page 8 3/8” CURVED BFP-51750 SHCS 3/8” x 2 3/4” WASHER instead of a 3/8” FLAT WASHER. BFP-52345 SHCS 3/8” x 4” BFH-50204 3/8” Curved Washer BFH-50146 3/8” Flat Washer BFH-50157 3/8” Nylock Batca Fitness Systems AFTS Owner's Manual...
- Page 9 Skip this step and continue to next page (Step 3a) if the 200 lb weight stack option was purchased. This step is for the 150 lb weight stack option. Step 3: Make sure all hardware has been tightened before moving to next step. Part # Description BFM-52488...
- Page 10 Weight Plate BFM-51173 Magnetic Weight Stack Pin W/Lanyard BFM-50529 Rubber Donut All Flat Washers and Nylocks are 3/8” unless BFH-50119 HCS 3/8” x 1 1/4” otherwise noted. BFH-50147 3/8” Lock Washer BFH-50146 3/8” Flat Washer Batca Fitness Systems AFTS Owner's Manual...
- Page 11 Step 4: Make sure all hardware has been tightened before moving to next step. Cable locks out in the bottom hole of the Adjustment Assembly if 150 lb weight stack Is installed START HERE Cable locks out in the top hole of the Adjustment Assembly if 200 lb weight stack Is installed.
- Page 12 Short Bar BFM-10682 Long Bar BFC-50136 Ankle Strap BFC-10103 Strap Handle All Flat Washers and Nylocks are 3/8” unless BFP-51759 SHCS 3/8” x 2 1/4”” otherwise noted. BFH-50146 3/8” Flat Washer BFH-50247 3/8” Thin Nylock Batca Fitness Systems AFTS Owner's Manual...
- Page 13 AFTS Weight Stack Enclosures Option Installation Step 6: The HCS 3/8” x 1 1/4” are the same bolts from Step 3. Remove them in order to install the Shroud Connector. Part # Description Hardware Shown/Listed is for installing BFM-11189 Shroud Connector weight stack enclosure on one side.
- Page 14 5 /16” Flat Washer BFM-52498 Accessory Storage Shelf BFH-50267 5/16” Nylock BFM-52491 Tablet Holder BFH-50146 3/8” Flat Washer BFH-50144 FHSCS 5/16” x 1” BFH-50247 3/8” Thin Nylock BFH-50145 FHSCS 5/16” x 2 1/4” BFH-50157 3/8” Nylock Batca Fitness Systems AFTS Owner's Manual...
- Page 15 Final Assembly and Troubleshooting Weight Stack Decals: 200lb Stack (For the 150 lb Weight stack use 10-150 stickers and discard the rest) IMPORTANT - Check These Components Before Using Gym: Each Cable with a threaded bolt on • either end must be threaded at least 1/2”...
-
Page 16: Preventive Maintenance
Preventive Maintenance Batca Fitness Systems strives to give you the very best in quality, performance and safety through carefully engineered designs and excellent workmanship. In order to maintain this high level of quality the preventative maintenance schedule below should be followed. -
Page 17: Limited Lifetime Warranty
Batca Fitness Systems are also not covered by this warranty. Only genuine Batca parts should be used for replacement, repair, and maintenance for this warranty to apply. -
Page 18: Layout Diagram
The AFTS has a layout dimension of 3-8”” (Length) x 4’-6” (Width) x 6’-11” (Height). The length with the Accessory Storage Option is 4’ -3.5” There should be minimum of 18”, preferably 24” of working space around the entire unit. Batca Fitness Systems AFTS Owner's Manual...
Need help?
Do you have a question about the AXIS Free Trainer-S and is the answer not in the manual?
Questions and answers