Machine overview ........................ 52 Labelling ............................ 59 Baling process ........................... 60 Compressing a big bale ...................... 61 Overview of the drives ....................... 61 4.5.1 Main drive .......................... 61 Overload protection on the machine .................. 62 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 4
Setting the bale chute ...................... 106 7.15 Mounting fire extinguisher...................... 107 7.16 Converting the drawbar from bottom to top hitching .............. 107 7.17 Converting the drawbar from top to bottom hitching .............. 108 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 5
Connecting foreign ISOBUS terminal .................. 120 8.10 Connecting joystick ........................ 121 8.11 Connecting the camera to the KRONE ISOBUS terminal CCI 800 or CCI 1200 ..... 124 8.12 Mounting the safety chain ...................... 124 Operation .......................... 126 Preparation for baling process .................... 126 Applying/releasing flywheel brake ...................
Page 6
Switching the warning beacon on/off .................. 165 9.23 Removing/mounting the safety device which prevents unauthorised use ....... 166 9.24 Operation of machine without bale chute ................ 166 KRONE ISOBUS terminal (CCI 800, CCI 1200) .............. 168 10.1 Touchable display ........................ 168 10.2 Switching terminal on/off...................... 169 10.3...
Page 7
Menu 14-2 “Driving speed/direction of travel diagnostics” ............ 245 14.16.2 Menu 14-3 "Configuring main window" .................. 246 14.16.3 Menu 14-4 "Set background colour" .................. 248 14.16.4 Menu 14-5 "KRONE SmartConnect" .................. 249 14.16.5 Menu 14-9 “Switching Between the Terminals” ............... 249 14.17 Menu 15 "Settings" ........................ 250 14.17.1 Menu 15-1 “Sensor Test”...
Page 8
Packer gearbox........................ 311 20.4 Transfer gearbox ........................ 312 20.5 Gearbox pick-up top part ...................... 313 20.6 Gearbox pick-up bottom part .................... 314 20.7 Knotter gearbox ........................ 314 20.8 Gearbox starter aid ........................ 315 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 9
Car jack contact points ...................... 343 Waste disposal........................ 345 Appendix .......................... 346 25.1 Hydraulic diagram – Working hydraulics ................. 346 25.2 Hydraulic diagram - on-board hydraulic system .............. 349 Index............................ 351 Declaration of conformity ..................... 363 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Information on This Document Validity This document is valid for machines of type: BP305-10 (BiG Pack 1270) All information, illustrations and technical data in this document correspond to the latest state at the time of publication. We reserve the right to make design changes at any time and without notification of reasons.
This arrow identifies the result of an action step or sequence of actions. This bullet point identifies an enumeration. If the bullet point is intended, it identifies the second level of the enumeration. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 12
The signal word DANGER warns of a hazardous situation which will result in serious injuries or death if the warning sign is ignored. WARNING The signal word WARNING warns of a hazardous situation which will result in serious injuries or death if the warning sign is ignored. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Factor Inch-pound units Unit name Abbrevi- Unit name Abbrevi- ation ation Area Hectare 2.47105 Acre acres Volume flow Litres per minute L/min 0.2642 US gallons per minute Cubic metres m³/h 4.4029 per hour BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 14
Kilometres per km/h 0.6215 Miles per hour hour Volumes Litres 0.2642 US gallon US gal. Millilitre 0.0338 US ounce US oz. Cubic centi- cm³ 0.0610 Cubic inch in³ metre Weight Kilogram 2.2046 Pound BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 15
Information on This Document How to use this document This page has been left blank deliberately. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
• Attachment of unauthorised or unapproved additional equipment • Use of spare parts which are not KRONE original spare parts • Stationary operation of the machine Unauthorised modifications to the machine may affect the properties of the machine or disrupt proper operation.
He has read the operating instructions and can implement the information in the operating instructions accordingly. • He is familiar with driving vehicles safely. • For road travel he has adequate knowledge of the highway code and has the stipulated driving licence. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
2.4.6 Structural modifications on the machine Structural modifications and extensions that were not approved by KRONE can impair the functionality, operational safety and also the road traffic certification of the machine. As a result, persons can be seriously injured or killed.
Determine the cause of damage according to these operating instructions and repair the damage, if possible, Page 327. In case of damage which may affect operational safety and cannot be repaired according to these operating instructions: Have damage repaired by a qualified service centre. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 29. This also applies to brief inspection work. Consider the information in all relevant operating instructions: • the operating instructions for the tractor • the operating instructions of the machine • the operating instructions of universal shaft BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 21
In case of dangerous situations, immediately switch off drives and instruct people to leave the danger zone. Danger zone due to trailing machine parts If machine parts are trailing, people may be seriously injured or killed. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Use only personal protective equipment which is in proper condition and offers effective protection. Adjust personal protective equipment to the person, for example the size. Remove unsuitable clothing and jewellery (e.g. rings, necklaces) and cover long hair with a hairnet. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Consider the overall width of the combined tractor and machine. Consider the larger swivel range when cornering. Adjust the driving speed when cornering. When turning, watch out for people, oncoming traffic and obstacles. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Foreign objects and/or liquids in the hydraulic system and/or fuel system may impair the operational safety of the machine and cause accidents. Clean all connections and components. Close open connections by means of protective caps. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Jump away from the machine. Jump into a safe standing position. Do not touch the machine from the outside. Move away from the machine in very small steps keeping your feet close together. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Damaged compressed-air hoses of compressor unit can tear off. Hoses moving in an uncontrolled manner can cause severe injuries. Contact a specialist workshop immediately if you suspect that the compressor unit is damaged. Shut down and safeguard the machine, Page 29. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
If the machine is not shut down and safeguarded, parts may move unintentionally or the machine may start moving. Thus there is a risk of serious injuries or death. Before carrying out any repair, maintenance and cleaning work on the machine, shutdown and safeguard it, Page 29. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 28
Frame or supporting components • Running gear Before carrying out welding work on the machine, obtain consent by KRONE customer service and, if required, identify alternatives. Before performing welding work on the machine, park the machine safely and disconnect it from the tractor.
The fitting of wheels and tyres requires adequate knowledge and approved mounting tools. If there is a lack of knowledge, have the wheels and tyres fitted by the KRONE dealer or by a qualified tyre service.
Check installed seal rings for damage. Replace them if necessary. Collect leaking oil and/or waste oil in a container provided for this purpose, and dispose of it properly, Page 25. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Safety labels on the machine Every safety label is provided with an order number and can be ordered directly from the authorised KRONE dealer. Immediately replace missing, damaged and unrecognisable safety labels. When attaching safety labels, the contact surface on the machine must be clean and free of dirt, oil and grease to ensure optimum adhesion of the labels.
Page 32
Safety Safety labels on the machine Position and meaning of safety labels Left-hand machine side BP000-575 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 33
Danger due to crushing or shearing Risk of injury due to crushing or shearing points on moving machine parts. While parts are moving, never reach into areas where there is a risk of being crushed. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 34
When climbing onto the machine while the PTO shaft is run- ning, there is a risk of being pulled in by rotating machine parts. Before climbing onto the machine, switch off the PTO shaft and the engine. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 35
Safety Safety labels on the machine BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 36
Safety Safety labels on the machine Right-hand machine side BP000-576 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 37
5. Ord. no. 942 290 0 (1x) Danger due to fire Risk of injury due to fire on the machine. Do not operate the machine unless there is a functional fire extinguisher available. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 38
Safety Safety labels on the machine Front and rear view BP000-577 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Each information label has an order number. You can order the labels directly from your KRONE dealer. Replace missing, damaged and illegible information labels immediately. Prior to attaching an information label, ensure that the contact surface on the machine is clean and free of dirt, oil and grease so that the label can adhere to properly.
Page 40
Safety Information labels on the machine Location and meaning of the information labels BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 41
Safety Information labels on the machine BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 42
Safety Information labels on the machine Left and right side of the machine BP000-694 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 43
27 006 256 0 Screw in the system screw until it hits the stop (2). Æ The machine can only be operated with tractors that are equipped with a Load Sensing system (3). For details Page 105. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 44
Coupling/uncoupling the bale ejector via the stop cock, Page 152. 27 027 587 0 11. Ord. no. 27 027 617 0 (1x) The label shows how the spools of twine in the left-hand twine box are connected with each other. Page 132. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 45
27 021 260 0 with this information label. • Ord. no. 27 023 958 0 There are lashing points on the machine that are identified with this label, Page 272. 27 023 958 0 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 46
Safety Information labels on the machine Front/rear view BP000-696 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 47
27 021 260 0 with this information label. • Ord. no. 27 018 170 0 There are jacking points on the machine that are identified with this label, Page 343. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Safety Safety equipment Safety equipment BPG000-006 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 49
• The safety chain is used for the additional protection of trailed machines in case they become unhitched during transport, Page 124. • The country-specific regulations for using the safety chain during transportation of the machine must be observed. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
The SMV emblem (1) is at the rear in the centre or on left. If the machine is transported on transport vehicles (for example lorry or train), the SMV emblem must be covered or dismounted. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
- can be related to persons. Additional functions, which are contractually agreed with the customer (e.g. teleservice), allow the transmission of certain machine data from the machine. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
The machine data is specified on a type plate (1). The type plate is at the rear on the right side of the machine above the parking brake. KRONE Agriculture SE e24*167/2013*00165 Heinrich-Krone-Str. 10, D-48480 Spelle Series T/V/V Model Year Construction Year...
The machine number results from the last 7 digits of the vehicle identification number (5). To ensure that the data is always available, KRONE recommends that you enter it in the boxes on the front cover of these operating instructions.
The intermediate universal shaft drives the flywheel (4) via a friction disc clutch. The flywheel drives the main gearbox (5) via a cam clutch. The main gearbox The main gearbox (5) drives the plunger, distributes the force further to the right and left and drives the following gearboxes: BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
To avoid early wear of the overload protection, switch the PTO shaft off if the overload protection responds for a longer period of time. Shut down and safeguard the machine, Page 29. Remedy the malfunction, Page 327. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 63
Machine description Overload protection on the machine BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 64
Machine description Overload protection on the machine BPG000-097 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
The working height of the pick-up can be limited downward manually by moving the depth limiters (4) on both sides of the machine so that the crops can be taken up without using the guide wheels, Page 274. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
The bale length and the number of layers are set from the tractor via terminal, Page 201. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 67
MultiBale - operating description Please contact the KRONE dealer if the number of small bales shall be increased to 9. In case of 9 small bales, the variable length of the small bales is 30 - 135 cm. If you have set more than 6 small bales, there is an increased chance of knotter problems.
Twine feed - operating description INFO When placing the twine rolls in the twine box, make certain that the labeling on the twine roll can be read. Watch the side that is marked with “Above”. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 69
The large square baler is equipped with twine boxes on both machine sides which can be folded down hydraulically. Each twine box can hold 15 spools of twine. The 3 upper twines come from the 6 twine rolls (1) in the front. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
To ensure adequate tying safety, use only plastic twines with a running length of 100 – 130 m/kg. Use KRONE original twine. 4.12 Description of functions of electric twine empty display for lower...
(closing knot) is tied first, followed immediately by the second knot (starting knot). 1st knot: Closing knot, ties the pressed big bale. 2nd knot: Starting knot, ties the initial knot for the next big bale. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
The big bale is deposited From the bale chute on the field. Bale ejector The last big bale is transported to the bale chute by the bale ejector. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Then, the sub- progressive distributors pump the grease to the individual lubrication points. The lubrication duration and the break times are controlled via terminal, Page 216. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Load Sensing system) via the system screw (1) on the control block of the machine, Page 105. The control block sits at the front left on the frame, next to the distributor central electrical system. >>> 2 Adapting hydraulic system [} 105] BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Lever in position (II) = rolls can be turned freely In order to ensure that the last big bale can be put down properly, the bale brake must be released for the last bale. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
25 km/h, 40 km/h, 60 km/h Airborne noise emission Airborne noise emission Emissions value (sound pressure level) 74.2 db(A) Measurement device Bruel & Kjaer, Type 2236 Accuracy class Measurement uncertainty (according to DIN EN ISO 11201) 4 dB BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Twine wrapping and tying material Twine wrapping and tying material Roll length 100 – 130 m/kg Maximum diameter of the spool of twine 340 mm Maximum height of the spool of twine 370 mm BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
NOTICE Complying with change intervals for biooils To ensure high life expectancy of the machine, it is absolutely necessary to comply with change intervals for biooils due to the ageing of the oils. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
If oils, which have different specifications, are mixed with each other, the machine may be damaged. Never mix oils, which have different specifications, with each other. Contact your KRONE service partner before using an oil with a different specification after changing the oil. Bio-degradable lubricants on request 5.15.1...
Technical data 5.15 Consumables 5.15.3 silage additives Designation Filling quantity Specification Silage additives tank 400 l Use silage additives that are neither aggressive nor corros- ive. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
For details see the operating instructions of the tractor manufacturer. Single-acting control unit • Pressure: Raise pick-up • Float position: Lower pick-up Double-acting control unit • Raise hydraulic support jack • Lower hydraulic support jack Bale chute keypad BP000-531 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 82
• Inching = the function is executed as long as the key is pressed. • The LED shines when the key is pressed. • The bale chute is lowered when it is selected. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 83
2 seconds. • The LEDs (4, 5, 6) are blinking. • 10 bale ejections are performed. • Press the key 5 or 6 to terminate automatic bale ejection prematurely. • The bale ejector remains selected. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
The machine is delivered together with the following additional parts that can be found at the rear in the bale channel, in the left twine box, or in the tool box at the ladder. Parts in the bale channel BP000-685 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 85
Parts in the tool box on the ladder BP000-687 1 Safety device which prevents unauthor- 5 Shear bolts ised use 2 Twine guide eyes 6 Locknuts 3 Retaining rings 7 Sensor key 4 Shear bushings 8 Pivoted knotter lever BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
ü The tyres have been checked and the tyre pressure is adjusted correctly, Page 289. ü The road travel lighting has been checked for function and cleanliness, see Page 116 ü The supplied operating instructions are in the document storage tube. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Attach the supplied support jack (7) to the hoist (6) and lift it. Mount the screws (2) with the detent edged washers and nuts. Tighten the screws (2) to the corresponding tightening torque, Page 284. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 88
Mount the hydraulic hose line (3) DKOL/DKOL on the ball valve (7). Mount the Kennfix (1) on the hydraulic hose line (2) DKOL/DKOL90°. Mount the Kennfix (4) on the hydraulic hose line (3) DKOL/DKOL. Connect the hydraulic hose lines (2, 3) on the tractor side. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Attach the supplied support jack (7) to the hoist (6) and lift it. Mount the screws (2) with the detent edged washers and nuts. Tighten the screws (2) to the corresponding tightening torque, Page 284. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Loosely pre-assemble the 3 upper and the 3 lower screws (2). Loosely pre-assemble the 2 middle screws (4) with disc (5). Tighten the screws (2,4) crosswise to a tightening torque of 300 Nm. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Mounting the central lubrication line on the drawbar eye The mounting material for mounting the central lubrication line can be found at the rear left in the tool box on the ladder. BP000-741 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
The routing path of all drawbar eye types (not the Cuna drawbar eye) is described below. The routing path of the Cuna drawbar eye is described separately, Page 94. BP000-738 Route the central lubrication line (1) along the installed hydraulic tubes (3) to the front part of the drawbar (4). BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
The routing path of the Cuna drawbar eye is described below. The routing path of other drawbar eyes is described separately, Page 93. BP000-742 Route the central lubrication line (1) along the installed hydraulic tubes (3) to the front part of the drawbar (4). BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Setting the drawbar height as a bottom hitching with other drawbar eyes or as a top hitching with other drawbar eye types is set in a similar way. Before making the setting BPG000-077 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
(cornering with maximum steering angle and simultaneously driving a slope up or down) without any contact of the both section tube ends. In this process, the displacement path (overlap) must be at least 220 mm, both in straight-ahead driving and when cornering. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 97
In order to remove the protective cap (1) from the universal shaft half (2), push in the both locks (3) using a screwdriver and push back the protective cap (1). Put aside the protective cap (1) for later reinstallation. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 98
Mount the clamping bridge (4) by means of the screws (3). Determine dimension X and mark it on the outer guard tube (1). Remove the universal shaft halves (1,2) on tractor and machine side. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 99
Turn the collar (1) until you can feel a stop (6) and push back the outer guard tube (7). Dismounting inner guard tube BP000-395 Loosen the inner guard tube (1) from the slide ring (3) by lightly tapping the cap (2) and push it back. Dismount the seal (4). BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 100
Slide the seal (1) onto the section tube and mount with 2 screws (2). Æ The screws must not protrude into the inside of the tube. Grease the inner section tube (3) from the outside. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 101
Turn the collar (1) until you can feel a stop, refer to detail (I). Mount the 3 screws (5). Use a screwdriver (3) to pull the collar (1) over the locks (4) of the guard funnel (2) BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 102
Dismount the outer guard tube (3), Page 99. Drill three boreholes of Ø 25 mm into the outer guard tube (3), file them to an oblong hole and deburr. Mount the outer guard tube (3), Page 101. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 103
Mount the clamping bridge (7) by means of the screws (8). Tightening torque: M12=80 Nm, M14=130 Nm, M16= 200 Nm. Bring the machine into the widest position (straight-ahead driving). Shut down and safeguard the machine, Page 29. Determine the dimension Y. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
To reduce/increase the bending angle of the universally-jointed drive shaft, the powertrain on the intermediate bearing must be set, Page 104. 7.12 Drive train: Adjusting height The bending angle on the universally-jointed drive shaft (see Page 104) is set via the powertrain. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Shut down and safeguard the machine, Page 29. Operation of the machine on tractors with constant flow system For tractors with open hydraulic system: Unscrew the system screw (1) up to the stop. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
For this reason, the inclination of the bale chute with the "Weighing device" version is to be set less strong than the version without a weighing device. If the inclination of the bale chute is changed, the weighing device must be readjusted, Page 219. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
The drawbar is mounted as standard as bottom hitching (I). To convert from bottom hitching (I) to top hitching (II), the front part of the drawbar (3) and the drawbar eye (1) are turned by 180 degrees. BP000-083 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Turn the front part of the drawbar (5) by 180°, guide them between the drawbar (3) and mount them with the screw connection (4). Assemble the drawbar eye (1) with the screw connection (2). Adjust the drawbar height, Page 95. Check the bending angle of the universally-jointed drive shaft, Page 104. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
(e.g. ball-head hitch) must be in a horizontal position (+/- 3°) with respect to the ground so as not to obstruct the operational swivel angle between the mechanical connection devices. For the "Drawbar eye" version For "Ball head drawbar eye 80" version BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 110
The drawbar has to be lowered via support jack until the ball drawbar eye rests on the ball- head hitch. Shut down and safeguard the machine, Page 29. Secure the hitching device according to the operating instructions of the tractor manufacturer. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
To prevent damage to the machine, check the length of the universal shaft whenever you change tractors. Have it corrected by a KRONE service partner if necessary. BP000-678 ü The machine is shut down and safeguarded, Page 29.
Page 112
Otherwise parts may touch the universal shaft which leads to damages at the tractor and/or machine. Ensure there is enough room for the universal shaft to swivel in all operating states (cornering with maximum steering angle). BP000-096 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Check the hydraulic hoses for abrasion and pinch point and replace if required. BPG000-104 Depressurise the tractor hydraulics. Shut down and safeguard the machine, Page 29. Clean and dry the connections of the hydraulic quick connector. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
A hydraulic brake may be required on the machine to meet country specific standards. A brake valve is required on the tractor for the hydraulic brake. The corresponding hydraulic hose is connected to the brake valve on the tractor. The brake is activated by actuating the brake pedal. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Then connect the supply line (2) (red coupling head). Disconnecting Observe the correct order when disconnecting the compressed air lines. Firstly, disconnect the supply line (2) (red coupling head). Then disconnect the brake line (1) (yellow coupling head). BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Route the lighting cable (2) so that it does not come into contact with the tractor wheels or other moving parts of the machine. Connecting KRONE terminal DS 500 NOTICE Short circuit caused by impurities and moisture in the plug connection The machine may be damaged by a short circuit.
Page 117
Start-up Connecting KRONE terminal DS 500 Tractors with integrated ISOBUS system EQ003-251 ü The machine has been shut down and secured, Page 29. Connection terminal to tractor Connect the 9-pin plug (2) of the cable (1) to the 9-pin socket (3) (In-cab). Connection tractor to machine INFO The cable (6) can be ordered by quoting the order number 20 086 886 *.
EQ003-252 ü The machine has been shut down and secured, Page 29. ü The accessories kit B290 “KRONE tractor retrofitting” is mounted. Connection terminal to tractor Connect the 9-pin plug (2) of the cable (1) to the 9-pin socket (3) (In-cab). Connection tractor to machine INFO The cable (6) can be ordered by quoting the order number 20 086 886 *.
Page 119
Start-up Connecting the KRONE ISOBUS terminal (CCI 800, CCI 1200) Tractors with integrated ISOBUS system CCI 1200 CCI 800 EQ001-173 ü The machine has been shut down and secured, Page 29. Connection terminal to tractor Connect the 12-pin plug (2) of the cable (3) to the 12-pin socket (1) of the terminal.
EQ001-181 ü The machine has been shut down and secured, Page 29. ü The accessories kit B290 “KRONE tractor retrofitting” is mounted. Connection terminal to tractor Connect the 12-pin plug (2) of the cable (3) to the 12-pin socket (1) of the terminal.
INFO For further details on terminal connection, observe operating instructions of ISOBUS terminal manufacturer. 8.10 Connecting joystick INFO Follow the supplied joystick operating instructions for attachment of the joystick in the tractor cabin. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 122
Start-up 8.10 Connecting joystick KRONE ISOBUS terminal on tractors with integrated ISOBUS system EQ001-150 ü The machine has been shut down and secured, Page 29. Connect the 9-pin plug (2) of the cable (1) to the 9-pin socket (3) of the joystick.
Page 123
ü The machine has been shut down and secured, Page 29. ü The accessories kit B290 “KRONE tractor retrofitting” is mounted. Connect the 9-pin plug (2) of the cable (1) to the 9-pin socket (3) of the joystick. Connect the 9-pin plug (4) of the joystick to the 9-pin socket (5) (In-cab).
CCI 800 CCI 1200 EQ000-212 Insert the plug (4) on the camera (2) cable (3) into the connection C (1) of the KRONE ISOBUS terminal CCI 800 or CCI 1200 . To connect the plug (4) correctly, ensure that it is aligned with the marked points (5). 8.12...
Page 125
ü The machine is shut down and safeguarded, Page 29. Mount the safety chain (1) with the shackle (2) on the machine. BP000-106 Install the safety chain (1) at a suitable position (for example: [I] or [II]) on the tractor. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Switch to automatic mode in the terminal after the second big bale is finished, Page 190. Set the target baling force when in automatic mode, Page 200. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Æ If the flywheel is braked, no pressure builds up in the bale channel. Releasing the flywheel brake In order to apply the flywheel brake, switch the brake lever (1) from position (II) to position (I). Æ The flywheel is now unbraked. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
To lower the twine boxes, press and hold it down. Æ The swivelling twine boxes up function is blocked until the twine boxes are raised down via the terminal, Page 129. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Press ð The icons are displayed. To swivel down the twine boxes, press and hold BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
To swivel up the twine boxes, press and hold Æ The LED (5) shines and the LED (1) blinks. Æ The lowering twine boxes function is blocked until the twine boxes are swivelled down via the terminal, Page 129. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
ü The machine is shut down and safeguarded, Page 29. Securing To secure the knotter shaft, move the safety lever (1) from position (II) to position (I). Releasing To release the knotter shaft, move the safety lever (1) from position (I) to position (II). BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 29. ü The knotter shaft is secured Page 131. ü The twine boxes are lowered (via the terminal: Page 128, via the bale chute keypad: Page 130). ü The twine box hood is swivelled up, Page 131. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 133
Connect the front end of the twine of spool of twine (3b) with a reef knot to the end of the twine of spool of twine (3a). Shorten the ends of all reef knots tox=15-20 mm. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 134
Connect the front end of the twine of spool of twine (2c) with a reef knot to the end of the twine of spool of twine (2b). Shorten the ends of all reef knots tox=15-20 mm. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 135
Connect the front end of the twine of spool of twine (5b) with a reef knot to the end of the twine of spool of twine (5a). Shorten the ends of all reef knots tox=15-20 mm. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 136
Connect the front end of the twine of spool of twine (5c) with a reef knot to the end of the twine of spool of twine (5b). Shorten the ends of all reef knots tox=15-20 mm. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Route the lower twine (3) from the twine box (11) through the twine brake (6) to the twine guide (7). Route the 3 lower twines (1, 2, 3) from above through the eyes of the twine guide (7) and then further to the retaining clip (8). BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 138
Thread the lower twine from the twine guide (10) through the lower eye (11) and attach it on the brake rollers (12). Manually rotate the brake rollers (12). This guides the lower twine through the brake rollers (12). BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 139
Route the lower twine from the twine tension spring (14) between the rolls (15) of the knotter needle (16). Pull the lower twine down to the frame (17) and tie it to the frame (17). Repeat this process for all lower twines. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Route the 3 lower twines (1, 2, 3) from above through the eyes of the twine guide (9) and then further to the twine guide (10). Route the 3 lower twines (4, 5, 6) through the eyes of the twine guide (10) and then further to the lower twine brakes. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 141
Thread the lower twine through the upper eye (13). Route the lower twine further through the eye of the twine tension springs (14) and then upwards to the knotter needle. Repeat this process for all lower twines. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 142
Route the lower twine from the twine tension spring (14) between the rolls (15) of the knotter needle (16). Pull the lower twine down to the frame (17) and tie it to the frame (17). Repeat this process for all lower twines. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Route the 3 upper twines (1, 2, 3) through the eyes of the upper twine guide (7) and to the central lubrication guard (6). Route the 3 upper twines (1, 2, 3) through the eyes of the central lubrication guard (6) and to the twine brakes on the knotters. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 144
To tension the tensioning arm (2), pull back the upper twine before the central lubrication guard (3). If the bale channel is filled: Read the actual bale length on the terminal. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 145
Route the upper twine underneath the crossbeam of the knotter table and knot it on the crossbeam of the upper baling flap. To tension the tensioning arm (2), pull back the upper twine before the eye (1). BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Route the 3 upper twines (4, 5, 6) through the eyes of the upper twine guide (7) and to the central lubrication guard (6). Route the 3 upper twines (4, 5, 6) through the eyes of the central lubrication guard (6) and to the twine brakes on the knotters. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 147
To tension the tensioning arm (2), pull back the upper twine before the central lubrication guard (3). If the bale channel is filled: Read the actual bale length on the terminal. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Move the stop cock (1) into position (II). 9.12.2 Moving pick-up into transport/working position Working position In order to lower the pick-up into working position, move the single-acting control unit ) into the float position. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Switch off the PTO shaft and wait until trailing machine parts have come to a complete stop. Secure the tractor against rolling away. Apply the parking brake (see Page 157) and the flywheel brake (see Page 127) of the machine. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
To raise the bale chute, press and hold Æ The function is executed as long as the key is pressed. Æ The LED shines as long as the key is pressed. 9.13.2 Raising/lowering the bale chute via the terminal EQ001-205 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
To completely empty the bale channel, the front and the rear parts of the bale ejector must be coupled to each other. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Shut down and safeguard the machine, Page 29. Uncoupling To uncouple the bale ejector, move the stop cock (2) to position (II). Coupling To couple the bale ejector, move the stop cock (2) to position (I). BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 154), or automatic bale ejection (see Page 154) can be started. To release the baling flaps completely, press the key ( ) 2x within 2 seconds. Æ The LED flashes 3x and the baling flaps are released completely. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 154
) until the bale ejector is at the front. Move the bale ejector backwards/forwards until the bale channel is empty. After the big bale has been ejected, move the bale ejector back to the front. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Æ When the bale channel flaps are closed, first the bale channel flaps are opened and then 10 bale ejections are executed. 9.15 Operating the support jack INFO In order to increase the base of the support jack when the ground is soft, use a suitable support. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 156
Turn the crank handle (1) anti-clockwise until the drawbar eye is relieved. Operating the hydraulic support jack BPG000-110 ü The machine is shut down and safeguarded, Page 29. ü The machine is connected to the tractor, Page 109. ü The stop cock (1) is open, position II. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Locking Move stop cock (1) into position (I). Releasing Move the stop cock (1) into position (II). 9.16 Releasing/applying the parking brake BPG000-111 Shut down and safeguard the machine, Page 29. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Folding up the ladder Pull at the ladder (2) and fold it up until the ladder (2) is in contact with the magnets (1). Ensure that the ladder (2) is in contact with the magnets (1). BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
ü The machine is disconnected from the tractor. Triggering the tying cycle: ü The knotter shaft is released, Page 131. To trigger the tying cycle, pull the lever (1) of the electrical brake (2) in the direction of the arrow. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Switching working lights on and off via the bale chute keypad BP000-531 To switch on all working lights, press Æ The indicator lamp is lit. To switch off all working lights, press again. Æ The indicator lamp goes out. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Working lights – switching The working lights: on working lights • Knotter/pick-up lighting In "Rear working lights" version • Rear lighting In "Side hoods working lights" version • Side hoods lighting are switched on. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 162
Working light – switching • Is only available in "Side hood working off side hood lighting lights" version. Switch off warning beacon • see Page 165 Switch on warning beacon • see Page 165 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Æ The display switches from Switching off Press Æ The display switches from 9.22.4 Working lights – switching maintenance lighting on/off Press ð The icon is displayed when working lights –maintenance lighting are switched on. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Æ The display switches from Switching off Press Æ The display switches from 9.22.6 Working light – switching side hood lighting on/off Is only available in "Rear working lights" version Press BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Æ The icon is shown on the display when the warning beacon is switched off. Switching ON Press Æ The display switches from Switching off Press Æ The display switches from BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Establishing the plug connection (2) with the terminating resistor (1) is necessary if the machine is operated without bale chute. The plug connection sits near the 12-V socket (3), at the rear left under the machine. INFO The terminating resistor (2) can be ordered with the order number 20 086 023 0. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 167
Operation Operation of machine without bale chute 9.24 BPG000-114 ü The bale chute is dismounted. ü The machine is shut down and safeguarded, Page 29. Establish the plug connection (2) with the terminating resistor (1). BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
KRONE machines, which have ISOBUS equipment, are coordinated with this system. EQG000-057 The electronic equipment of the machine consists essentially of the job computer (1), the terminal (2) and the control and function elements.
KRONE ISOBUS terminal (CCI 800, CCI 1200) Switching terminal on/off 10.2 10.2 Switching terminal on/off EQ001-174 KRONE ISOBUS terminal CCI 1200 KRONE ISOBUS terminal CCI 800 Before switching on the terminal for the first time, check that the connections are correct and tight.
For more details on how the terminal functions, follow the terminal operating instructions. 10.4 Design of the KRONE machine application EQG000-059 The KRONE machine application is divided into the following areas: Status line (1) The status line (1) indicates current states of the machine (depending on how it is equipped), Page 176.
Page 171
KRONE ISOBUS terminal (CCI 800, CCI 1200) Design of the KRONE machine application 10.4 Keys (2) The machine is operated by pressing the keys (2) via touch function, Page 177. Main window (3) Values (figures) shown in blue in the main window can be selected using the touch function.
KRONE Terminal DS 500 11.1 Touchable display KRONE Terminal DS 500 NOTICE Penetration of water in the terminal could lead to malfunction. As a result, the machine can no longer be operated safely. Protect the terminal from water. If the machine is not used for an extended period of time (for example in winter), the terminal must be stored in a dry place.
Design DS 500 11.3 11.3 Design DS 500 EQ003-254 The KRONE machine application is divided into the following areas: Status line (1) The status line (1) indicates current states of the machine (depending on how it is equipped), Page 176. Keys (2) The machine is operated by pressing the keys (2) via touch function,...
Page 174
KRONE Terminal DS 500 11.3 Design DS 500 Keys (6) The keys (6) can be used to open the main menu or the working screen and to confirm the error messages and set the brightness. Icon Designation Explanation Main menu Open the main menu of the terminal.
KRONE ISOBUS terminal. Before commissioning, refer to the mode of operation of the KRONE ISOBUS terminal in the operating instructions. A major difference to the KRONE ISOBUS terminal is the arrangement and number of keys with functions determined by the selected external ISOBUS terminal.
If error messages are ignored and the malfunction is not remedied, people may be injured and/or the machine may be damaged seriously. Remedy the malfunction when the error message is displayed, Page 327. If the malfunction cannot be remedied, consult a KRONE service partner. 13.1 Status line INFO Using a terminal with a resolution of less than 480x480 pixels.
The icon flashes. Baling flaps closed 13.2 Keys EQ001-205 The available icons comply with the equipment of the machine. The following represented icons are not always available. Dimmed keys are currently not available. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 178
Starting automatic bale When the baling flaps are open ejection Implements 10 bale ejections. When the baling flaps are closed Opens the baling flaps and implements 10 bale ejections. see Page 196 Stopping the automatic bale ejection BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 179
• Alternatively, the working lights can be switched on and off manually. Working lights – switching • Alternatively, the working lights can be off automatic switched on and off manually. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 180
Working lights – switching • Is only available in "Rear working lights" off rear lighting version. Working light – switching • Is only available in "Side hood working on side hood lighting lights" version. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 181
The machine switches from manual mode to automatic mode. see Page 190 Switch to manual mode The machine switches from automatic mode to manual mode. see Page 190 Leave working screen Back to the previous working screen. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 182
5 seconds, the symbols for "Operate starter aid/collection" are no longer shown with the exception of the icon • Upon reaching the final speed, the icon changes from Switching off starter aid BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Current layer thickness • In cm or inch (depending on the set system of units). Packer filling degree (up- Packer filling degree: Depends on selected per bargraph) mode, Page 223. 100% Packer utilisation (lower bargraph) BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 184
• The blue value is touch-sensitive. Flywheel brake applied Knot run • Is displayed briefly after a knot is tied. • When the knotter signal is activated, a horn sounds for approx. 1 s, Page 211. Bale ejector active BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Displays on the information bar EQ001-049 INFO The information bar on the working screen can be individually configured, Page 246. The available icons comply with the equipment of the machine. The following represented icons are not always available. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 186
Total length of all pressed In m or ft (depending on selected system of bales units). The adjacent number indicates the selec- ted customer counter (customer counter 19 in the example). BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
ISOBUS Shortcut Button, at least one ISOBUS Shortcut Button must be available. The ISOBUS Shortcut Button can be integrated both in/on the terminal or can be available as an external momentary switch in the ISOBUS system. The KRONE Machine Controller (KMC) reads out the information whether an ISOBUS Shortcut Button is available in the ISOBUS system.
Page 188
Terminal – Machine functions 13.5 ISOBUS Shortcut Button (ISB) EQG000-022 If the KRONE Machine Controller (KMC) detects an ISOBUS Shortcut Button, the icon displayed when the terminal starts. If the KRONE Machine Controller (KMC) detects no ISOBUS Shortcut Button, the icon displayed when the terminal starts. Actuating ISOBUS Shortcut Button A stop command is sent to the ISOBUS when the ISOBUS Shortcut Button is pressed.
From the road travel screen Press Æ When the terminal is switched on, the machine starts in manual mode with a target bale channel flap pressure of 50 bars. 100% 100% EQ001-226 / EQ001-227 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Switching the warning beacon on/off Press Æ The icon is shown on the display when the warning beacon is switched on. Æ The icon is shown on the display when the warning beacon is switched off. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Working lights – switching working lights on/off Press ð The icon is displayed when working lights – working lights are switched on. ð The icon is displayed when working lights – working lights are switched off. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Is only available in "Rear working lights" version Press ð The icon is displayed when working lights –rear lighting are switched on. ð The icon is displayed when working lights –rear lighting are switched off. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Æ The display switches from Switching off Press Æ The display switches from 13.17 Releasing/locking self-steering axle Releasing Press ð The icon flashes until the self-steering axle is released. Æ The display switches from BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
When the speed of the starter aid is reached, the system switches off the starter aid. The display switches from 13.18.2 Switching off starter aid To switch off the starter aid, press Æ The display switches from Æ The starter aid is switched off. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
To lower the bale chute, press and hold 13.20.2 Lift bale chute WARNING! Increased risk of injury! While the bale chute is being raised, ensure that there is nobody in the danger zone (particularly behind the machine). BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
To bring up the menu level from the working screen, press Æ The display indicates the menu level. 13.24 Operating the knotter Press the icon to display the icons = trigger knotter = reset current bale length to zero BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
= lower twine box = raise twine box = swivel twine boxes up = swivel twine boxes down on the display. 13.25.1 Lowering the twine boxes ü The twine boxes are swivelled down, Page 199. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
ð The icons icons are displayed. To swivel up the twine boxes, press and hold Æ The lowering twine boxes function is blocked until the twine boxes are swivelled down via the terminal, Page 199. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Value (2) and the red mark on the bar display = set target bale channel flap pressure Setting the target bale channel flap pressure ü Manual mode has been selected, Page 190. Change the value, Page 208. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Value (1) and the bar display = actual bale length Value (2) and the red mark on the bar display = set target bale length Setting target bale length Setting range: 1,000 – 3,200 mm/39 – 126 inch Change the value, Page 208. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
The following functions are available in the “Auxiliary” (AUX) menu: auxiliary Function Increase baling pressure/baling force Reduce baling pressure/baling force Manual/automatic mode changeover Start/stop starter aid Lock/release self-steering axle BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Recommended configuration of an AUX joystick CCI A3 Operating level 1 EQ001-149 The indicator lamp (2) shines, showing that operating level 1 is active. Actuate the switch (1) on the rear, the next operating level is displayed. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Duration of cleaning operation, see Page 213 Calibrating MultiBale, see Page 214 Sensitivity direction display, see Page 216 Central lubrication, see Page 216 Weighing device, see Page 217 Moisture measurement, see Page 219 Error message for moisture measurement, Page 220 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 204
Silage additives tank, see Page 231 12-2 Silage additives dosing, see Page 232 Counter, see Page 238 13-1 Customer counter see Page 239 13-2 Total counter, see Page 243 ISOBUS, see Page 244 14-2 Driving speed/direction of travel diagnostics, Page 245 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Explanation Up arrow Move up to select something. Down arrow Move down to select something. Right arrow Move right to select something. Left arrow Move left to select something. Disk Save the setting. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Menu 1 "Knotter" see Page 209 Menu 2 "Sensitivity direction display", see Page 216 Menu 3 "Central lubrication", see Page 216 Menu 4 "Weighing device", see Page 217 Menu 5 "Moisture measurement”, see Page 219 Menu 7 "Packer", see Page 223 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
To call up the menu, press the scroll wheel. Æ The menu opens. For version with touch-sensitive terminal By pressing the icons To call up a menu, press the icon (e.g. ) in the display. Æ The menu opens. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Tap on the value. ð An input mask opens. Increase or reduce the value. In order to save the value, press Æ The setting is saved and the input mask closes. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Æ The display shows the "Knotter" menu. The "Knotter" menu is divided into the following sub-menus depending on the machine configuration: Knotter, see Page 209 Correction value bale length, see Page 210 Knotter signal, see Page 211 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
• If a correction value of e.g. 110 % is set, the bale will be 10 % longer. • Factory setting: 100 % Increase or reduce the value, Page 208. In order to save the value, press BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
This menu can be used to set whether the upper twines of the knotters are to be monitored. The knotters are numbered in direction of travel from left to right: Knotters from 1 to 6. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
14.7.4 Menu 1-4 “Blowing Interval Knotter Cleaning" This menu can be used to set after how many bales the knotters are blown off with compressed air to remove dust and accumulation of crops. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
This menu can be used to set how long the knotters are blown. 0,5s EQ001-005 / EQ001-063 ü Menu 1 "Knotter" has been selected, Page 209. To open the menu, press Æ The display shows the "Blowing time" menu. Recurring icons Page 205. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
To open the menu, press Æ The display shows the "Calibrate MultiBale" menu. Recurring icons Page 205. ü The machine is shut down and safeguarded, Page 29. ü The compressor unit has been filled. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 215
4,9V 1,1V 1,1V EQ001-082 / BP000-390 Call up the working screen. In the working screen, set the number of MultiBales ( ) to 1, Page 201. Call up the "Calibrating MultiBale" menu, Page 214. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
In order to save the value, press 14.9 Menu 3 "Central lubrication" For the "central lubrication" version This menu displays the non-adjustable lubrication intervals of the central lubrication. In addition, intermediate lubrication can be manually actuated. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Menu 4 "Weighing device" For "Weighing device" version In this menu a correction value can be set for the weighing device if the calculated weight (2) deviates from the weight of external calibrated scales. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 218
Æ If the displayed value corresponds to the weight of the test weight, it is not necessary to adjust the weighing device. Æ If the displayed value differs from the weight of the test weight, the weighing device must be adjusted. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Æ The icon is briefly displayed and the value is saved. INFO If the limit range is not adequate to adjust the weighing device, contact KRONE customer service. Zeroising the weighing device If there is no bale (weight) on the bale scale when the bale chute is lowered but a value (2) is displayed, the sensors B55 "Force sensor rear left"...
Æ The display shows the "Error message for moisture measurement" menu. Recurring icons Page 205. Setting value for display Increase or reduce the value, Page 208. In order to save the value, press BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Æ If the measured value matches the value (2) on the display, the moisture measurement has been correctly set. Æ If the measured value does not match the value (2) on the display, the correction value (1) must be set. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 205. You can select between 2 modes: Icon Designation Explanation Internal moisture measure- • Must be activated if the KRONE ment moisture measurement is to be used. Mode 1/2 External moisture meas- • Must be activated if the external urement moisture measurement is to be used.
14.12.1 Menu 7-1 "Packer filling" EQ001-228 / EQ001-231 ü Menu 7 "Packer" has been called up, Page 223. To open the menu, press Æ The display shows the "Packer filling" menu. Recurring icons Page 205. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
The higher the switching threshold for actuating the Variable Filling System, the more crops are collected in the feed channel. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
In " Packer 1:1" mode, the packer drum fills the feed channel. With each plunger stroke, the sensing rake swings back and the bale channel is filled with crops through the feeder strip. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
When the "Packer test" submenu has been exited, the mode of the "Packer filling" menu is active again. EQ001-228 / EQ001-230 ü Menu 7-1 "Packer filling" has been called up, Page 223. Press to call up the "Packer test" submenu. Display area You can select between two modes: BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
0 mV 1043 mV EQ001-259 / EQ001-260 ü Menu 7 "Packer" has been called up, Page 223. To open the menu, press Æ The display shows the "Calibrate sensing rake" menu. Recurring icons Page 205. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
B39 is automatically adjusted by the system. If the sensor B39 cannot be calibrated, the installation position of the sensor wheel must be checked or adjusted by a KRONE service partner. 14.13 Menu 8 "Self-steering axle"...
Page 229. Changing the mode Select and save the mode, Page 209. 14.13.1 Setting the speed for blocking the self-steering axle AUTO AUTO km/h EQ001-206 / EQ001-207 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
ü For The menu level is active, Page 206. To open the menu, press Æ The display shows the "Silage additive unit" menu. Depending on the machine equipment, the "Silage additives unit" menu is subdivided into the following sub-menus: BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
• The error message 522099-18 "Silage additives tank empty" appears in the display when the silage additives level reaches the selected value (2). Increase or reduce the value, Page 208. In order to save the value, press BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Silage additives dosing • Intended to rinse the silage additives continuous operation unit. • The pump runs continuously. Mode 5/5 • The pump output can be adjusted in percent, Page 237. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Checkbox not activated ( ): A fixed weight of the big bale can be entered. The system uses the fixed weight to determine the amount of silage additives to be added to the crops. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 234
EQ001-248 / EQ001-252 ü For The menu level is active, Page 206. ü Menu 12-2 "Silage additives dosing" is called up. AUTO Select and save the " Silage additives dosing by weight" mode. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Silage additives are added to the crops based on the average value. If the actual degree of moisture is higher than or equal to the third value (here 30), silage additives are added to the crops based on the individually entered value (here 2.5 l/tonne). BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 236
• The value (5) must be higher than the value (4). • The value (5) must be lower than the value (6). Silage additives quantity • Touch to select the value. • The value (6) must be higher than the value (5). BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
AUTO EQ001-248 / EQ001-256 ü For The menu level is active, Page 206. ü Menu 12-2 "Silage additives dosing" is called up. Select and save the " Silage additives dosing continuous operation" mode. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Æ The display shows the menu "Counter ". Depending on the machine equipment, the "Counters" menu is divided into the following sub- menus: Icon Designation Menu 13-1 "Customer counter", see Page 239 Menu 13-2 "Total counter", see Page 243 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Setting all customer coun- All 20 customer counters and their detail ters to zero counters are set to zero. The name is retained. Changing the designation of a customer counter Press on “Designation”. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
NAME 2 NAME 3 100.0 NAME 4 NAME 5 225 t EQG000-055 Customer counter Detail counter Call detail counter ü The menu 13-1 "Customer Counter" is selected. To select the detail counter, press BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 241
For version with "MultiBale": Including the MultiBale knot "Total weight" counter For "Weighing device" version: Total weight of all bales “Average weight” counter For "Weighing device" version: Average weight of the weighed bales BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 242
• the day counter • the "Total length" counter • the knot counter • For "Weighing device" version: The "total weight" counter • For "Weighing device version": The "average weight" counter BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
• Total length of all bales for this customer. • In m or ft (depending on selected system of units). Bale counter Cannot be deleted Season counter 1 Can be deleted Season counter 2 Can be deleted BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
ü The menu level is open, Page 206. To open the menu, press Æ The display shows the "ISOBUS" menu. Depending on the machine equipment, the "ISOBUS" menu is divided into the following submenus: BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Display area Icon Designation Explanation <--- 0 Driving forward 0 ---> Reverse travel +25.5 km/h Speed for forward travel km/h or mph depending on set system of units. -25.5 km/h Speed for reverse travel BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
14-3 EQ001-077 / EQ001-078 ü The menu 14 “ISOBUS” has been selected, Page 244. To open the menu, press Æ The display shows the "Configure main window" menu. Recurring icons Page 205. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 247
Current degree of moisture Is always available. of the crops Data is only recorded if an external mois- ture measurement has been installed on the machine. Bale weight Weight of the last weighed bale BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
ü The menu 14 “ISOBUS” has been selected, Page 244. To open the menu, press Æ The display shows menu "Background colour ". Recurring icons Page 205. Display area You can select between three modes. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
• Tractor parking light off, background colour white. Changing the mode Select and save the mode, Page 209. 14.16.4 Menu 14-5 "KRONE SmartConnect" The access data for the KRONE SmartConnect (KSC) can be seen in this menu. 14-5 WLAN-NAME: 00011501 WLAN-KEY: afbb2bfac5 PRODUCT-CODE:...
ü For The menu level is active, Page 206. To open the menu, press Æ The display shows the "Settings" menu. The “Settings” menu is divided into the following sub-menus depending on the machine configuration: BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
15-1 state: 8,3V 7,3V 5,2V 2,4V 7,8V EQ001-080 / EQ000-040 ü Menu 15 “Settings” is called, Page 250. To open the menu, press Æ The display shows the "Sensor test" menu . BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 252
A33B2 A33B2 Silage additives fill level Flywheel brake Central lubrication Plunger at rear (measuring) Front plunger (calibrate) Rotational speed of packer Packer feed active Lower twine monitoring Needle connecting rod left Knotter monitoring BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 253
Force sensor right Pick-up speed Position MultiBale Bale on scale Pick-up position Packer position Contact pressure feed rotor Bale chute top Rotational speed PTO shaft Rotational speed feed rotor Weighing device acceleration sensor BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 254
Force sensor rear Consisting of: B53 Force sensor rear left B54Force sensor rear right Twine box transport position left Twine box transport position right Twine box maintenance position left Twine box maintenance position right BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 255
When the pushbutton is not pressed, the bar must be in the upper marked area of the bar display. 15-1 state: 3,3V 2,5V 1,3V 0,6V 3,1V EQ000-042 Possible pushbuttons (depending on the machine configuration) Electrical component identification: BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
To open the menu, press Æ A message opens which refers to the operating instructions Observe the safety routine "Run actuator test", Page 31. Confirm with Æ The display shows the "Actuator test" menu. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 258
Warning beacon right Pick-up lighting Working light rear left Working light rear right E6/E7 E6/E7 E6= Knotter table lighting E7= Lower twine lighting E8/E9 E8/E9 E8= Lighting twine box right E9= Lighting twine box left BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 259
A current (in mA) can be set with the PWM value (in parts per thousand). With a value of PWM = 500, the current should be between 500 mA and 3000 mA (depending on the valve that is used and the operating temperature). BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
All active and non-active errors are shown in this menu. The errors are shown with a number indicating how often the error occurred and the time on the operating hours counter when the error last occurred. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 261
• All inactive errors are deleted. Recurring icons Page 205. Delete individual errors Only non-active errors (highlighted grey) can be deleted. To select the error to be deleted, press To delete the error, press BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 262
Terminal – Menus 14.17 Menu 15 "Settings" Delete all errors Only non-active errors (highlighted grey) can be deleted. To delete all errors, press BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Machine components could be moved unintentionally when stop cocks are open. This may result in serious accidents. In order to avoid that functions are triggered by mistake, the stop cock/s must be closed during transport/road travel. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 157. ü The control units on the tractor are in neutral position and locked. ü The brake is functioning properly. ü The road lighting has been connected, tested and is functioning properly, Page 116. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Drive the tractor a short distance straight forward until the steered wheels are straight. Reverse travel Set the wheels of the self-steering axle straight (see Page 265) and lock the self-steering axle (see Page 266). BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 266
ð The icon flashes until the self-steering axle is locked. Æ The display switches from Depressurise the control unit ( Releasing Press ð The icon flashes until the self-steering axle is released. Æ The display switches from BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Æ As soon as the hoses are again connected to a compressed air brake system, the button (2) is pushed back automatically into its initial position (II). 15.5 Releasing the hydraulic brake for manoeuvring the machine ü For “self-steering axle” version: The wheels are straight, Page 265. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
In "hydraulic brake (export)" version: Disconnect the connection for the hydraulic brake and attach it to the hose support of the machine. In "hydraulic brake (export France)" version: Loosen the safety chain on the tractor side. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Close the front hood (1). To secure the front hood, wrap a cable tie (3) around the handle (2) and thread it through the borehole (3) in the drawbar beam. Tighten the cable tie (3). BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Wrap a cable tie (1) around the stop (3), pull the cable tie through the borehole (4) in the stop (3) and route it further around the guide wheel bracket (2). Tighten the cable tie (1). Ensure that the guide wheels are secured. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
2 Yoke suspension point on left 4 Drawbar suspension point at front right Use a hoist with a minimum lifting capacity (depending on the approved total weight of the machine), see machine rating plate, Page 59. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Lashing points on the machine BPG000-078 1 Drawbar lashing point at front left 4 Drawbar lashing point front right 2 Cross-member lashing point rear left 5 Transport drawbar eye (with delivery) 3 Cross-member lashing point rear right BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
In order to prevent damages at the guide wheels and an increased wear to the pivot point of the pick-up, limit the lowering of the pick-up by means of the depth limiters, Page 274. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Check whether the depth limiters on both sides of the pick-up are in the same position. Lock the stop cock, Page 148. To lower the pick-up, set the control unit ( ) to float position. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
The crop press roller unit is used for accident protection! If the machine is operated without a roller crop guide, people can be seriously injured or killed. Never operate the machine without a crop press roller unit. Setting the height of the crop press roller unit BPG000-036 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
ü The machine is shut down and safeguarded, Page 29. In order to increase the bearing pressure, loosen the nut (3). In order to increase the bearing pressure, loosen the nut (3). 16.4 Setting the knotter shaft brake BPG000-052 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Changes to the knotter shaft brake influence the properties of the entire tying cycle of the machine. This may negatively influence or impair the tying cycle. To avoid malfunctions in the tying cycle, have the following adjustments/checks carried out by a KRONE service partner. Set the dimension X.
The factory setting applies for original KRONE twine with a running length of 100-130 m/kg. If knotter errors occur when using twine with a different running length, the twine brake must be set.
If the relevant safety routines are not observed, persons may be seriously injured or killed. The safety routines must be read and observed to avoid accidents, Page 29. INFO If new components need to be ordered for maintenance, use only KRONE original spare parts. 17.1 Maintenance table 17.1.1...
Cleaning the silage additives tank see Page 322 Rinse the silage additives unit with clear wa- see Page 323 ter. Have brake pads checked by KRONE service partner Checking/tensioning drive chains of the pick- see Page 288 Checking the functionality of the central lubric-...
Have the slack adjuster of the brake system checked by KRONE service partners Check the hydraulic hoses for leaks and, if ne- see Page 305 cessary, have them replaced by a KRONE service partner. 17.1.4 Maintenance - Once after 50 hours...
Maintenance - Every 200 hours Changing oil Main gearbox see Page 310 Packer gearbox see Page 311 Transfer gearbox see Page 312 Gearbox pick-up top part see Page 313 Gearbox pick-up bottom part see Page 314 Compressor see Page 318 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Maintenance - General information 17.2 Tightening torques Components Have the slack adjuster of the brake system checked by KRONE service partners Check the fire extinguishers see Page 290 17.1.8 Maintenance - every 2 years Components Have compressed-air tanks checked by KRONE service partner...
Page 285
1,914 M30 x 1.5 2,100 2,650 Metric thread screws with countersunk head and hexagon socket INFO The table applies only to countersunk screws with hexagon socket and metric thread tightened via hexagon socket. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 286
Bleed valve made of brass copper ring Ventilation/breather filter made of Ventilation/breather filter made of brass steel Steel and cast Aluminium Steel and cast Aluminium Maximum tightening torque (Nm) (±10%) M10x1 M12x1.5 G1/4“ M14x1.5 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 287
After the machine has been cleaned with water, lubricate all manually lubricated lubrication points, Page 299. After the machine has been cleaned with water, carry out a manual intermediate lubrication with the central lubrication unit, Page 217. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
By screwing in the screw (1), increase the chain tension of the drive chain (3). Secure the screw (1) with the counter nut (2). Close the guard sheet. Shorten too long chains by removing a chain link. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Inspect the tyres visually Visually inspect tyres for cuts or breaks. Æ If there are cuts or breaks in the tyres, have the tyres repaired or replaced by a KRONE service partner. Maintenance intervals for visual inspection of the tyres, Page 280.
Ensure that the fire extinguisher (1) is mounted on the machine. Ensure that access to and view of the fire extinguisher (1) are not obstructed. Ensure that the fire extinguisher (1) is filled by weighing the fire extinguisher (1). BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Visually inspect the drain valve (2) to ensure that it is not defective or soiled. Æ If the drain valve (2) is defective and is no longer sealed, immediately have the drain valve (2) replaced by a KRONE service partner. Æ If the drain valve (2) is soiled, clean the drain valve (2).
The drive chains must always be adequately wetted with engine oil. Shut down and safeguard the machine, Page 29. Check the drive chains and sprocket wheels for wear. Check that the drive chains are centred on the sprocket wheels. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Æ When the wear limit (dimension Y<50 mm) has been reached, the friction discs must be replaced. Venting friction disc clutch Loosen the nuts (1) until the disc springs (4) have been relieved. Turn the universal shaft manually. Tighten the nuts (1) crosswise until the dimension is X=16.6 mm. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
ü The machine has been parked, Page 268. Determine the dimension X. If the wear limit (see table) dimension X is exceeded, the drawbar eye (1) must be replaced by a KRONE service partner. 17.12 Checking wear limit on drawbar eye 50 BP000-524 If the wear limit is exceeded (see table) and/or the ball drawbar eye is damaged, replace the drawbar eye (1).
ü The machine has been parked, Page 268. Determine the dimensions X,Y,Z. If a wear limit (see table) dimension X,Y,Z is exceeded, the drawbar eye (1) must be replaced by a KRONE service partner. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
ü The machine has been parked, Page 268. Determine the dimensions X,Y,Z. If a wear limit (see table) dimension X,Y,Z is exceeded, the drawbar eye (1) must be replaced by a KRONE service partner. 17.16 Checking the wear limit on the Cuna drawbar eye BP000-736 If the wear limit is exceeded (see table) and/or the ball drawbar eye is damaged, replace the drawbar eye (1).
ü The machine has been parked, Page 268. Determine the dimensions X,Y,Z. If a wear limit (see table) dimension X,Y,Z is exceeded, the drawbar eye (1) must be replaced by a KRONE service partner. 17.17 Retightening the screw connections on the drawbar eye BP000-528 Retightening of the screw connections (1) on drawbar eyes is described by way of example...
When using lubricating greases not approved and when mixing different lubricating greases, the lubricated parts may be damaged. Only use approved lubricating greases, Page 79. Do not use graphite-containing lubricating greases. Do not mix different lubricating greases. 18.1 Lubricating universal shaft DVG000-001 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Use the spray can to apply Oils Plant-based oils, unless spe- cified otherwise. a thin, even layer of oil. Oils Plant-based oils, unless spe- Apply the oil evenly. cified otherwise. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 300
Maintenance - Lubrication 18.2 Lubrication chart - machine BP000-648 Every 10 operating hours BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 301
Maintenance - Lubrication Lubrication chart - machine 18.2 Left-hand machine side BPG000-136 Every 200 operating hours BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 302
Maintenance - Lubrication 18.2 Lubrication chart - machine Right-hand machine side BP000-684 Every 200 operating hours BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 303
Maintenance - Lubrication Lubrication chart - machine 18.2 Lubrication points at the tandem axle BP000-649 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 304
Maintenance - Lubrication 18.2 Lubrication chart - machine Every 50 operating hours BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
6 years, including a maximum storage time of 2 years. The date of manufacture is printed on the hydraulic hoses. When checking hydraulic hoses, the state-specific conditions (e.g., BGVU) must be observed. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Æ In "Knotter cleaning" version: Top up oil when the level is below 20 L. If the oil level is too low, dismount the ventilation/breather filter (2) and top up the oil via the opening. For a list of oils Page 79. Mount the ventilation/breather filter (2). BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Wait until the operating temperature is reached before you press the contamination indicator (1) back in. The filter element must be replaced if the contamination indicator (1) pops out again. The high-pressure filter (2) of the on-board hydraulic system sits at the front right, behind the twine box. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 308
Screw the bottom part of the filter (5) all the way onto the top part of the filter (1) and then unscrew it one quarter turn. Charge the hydraulic system with pressure and check it for leaks. High-pressure filter (8) of the working hydraulics: Bleed the control block. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
If the relevant safety routines are not observed, persons may be seriously injured or killed. The safety routines must be read and observed to avoid accidents, Page 29. 20.1 Overview of gearboxes BPG000-122 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Refill with fresh oil via the oil filling hole (1) up to the middle of the inspection glass (2). Screw in the locking screw of the oil filling hole (1) and tighten it firmly, tightening torque Page 286. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Top up with fresh oil via the filling hole (3) up to the inspection hole (1). Screw the locking screw into the inspection hole (1) and the locking screw into the filling hole (3), tightening torque Page 286. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Top up with fresh oil via the filling hole (3) up to the inspection hole (1). Screw the locking screw into the inspection hole (1) and the locking screw into the filling hole (3), tightening torque Page 286. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Top up with fresh oil via the filling hole (3) up to the inspection hole (1). Screw the locking screw into the inspection hole (1) and the locking screw into the filling hole (3), tightening torque Page 286. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
(3), tightening torque Page 286. 20.7 Knotter gearbox INFO The oil level must be checked and changed with the machine in horizontal position. Use the lower edges of the cross-members as a reference edge. BP000-682 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
(3), tightening torque Page 286. 20.8 Gearbox starter aid INFO The oil level must be checked and changed with the machine in horizontal position. Use the lower edges of the cross-members as a reference edge. BPG000-123 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 316
Top up with fresh oil via the filling hole (3) up to the inspection hole (1). Screw the locking screw into the inspection hole (1) and the locking screw into the filling hole (3), tightening torque Page 286. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Remove the filter cartridge (4), knock out the dirt and blow it out from the inside to the outside with an air jet. ð Replace the filter cartridge (4) in case it is excessively soiled or damaged. Disassemble and tap out the cover (5). BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Screw in the drain plug (2) and tighten it firmly. Fill in new oil through the filling hole of the oil dipstick (1). Check the oil level with the oil dipstick (1). BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Before the season starts, empty the silage additives tank, fill it with clear water and run the silage additives unit in "continuous operation" mode for 10 min at a pumping rate of 75%, Page 237. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Residual liquid can be removed from the tion silage additives unit through the com- pressed-air fitting. Silage additives tank Two-way stopcock To lock/loosen the drain hose. pressure hose To connect an external water connection. Drip hose BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Set the two-way stopcock (1) to position II. Æ The silage additives run through a drain hose into the container provided. Once the silage additives tank is completely empty, turn the two-way stopcock (1) to position I. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Æ The silage additives/water run through a drain hose into the container provided. Insert the filter element (4) and the sealing ring (3) into the silage additives tank. Screw on the cover (2) and tighten it. Close the two-way stopcock at the drain hose, Page 321. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Screw the bottom part of the filter (5) together with the seal ring (4) to the filter head part (2) until it hits the stop. 22.6 Rinsing the silage additives unit BP000-824 ü The machine has been shut down and secured, Page 29. Connect an external water hose (2) to the pressure line (1). BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 324
Æ Alternatively, select "Silage additives dosing continuous operation" to rinse the silage additives unit, Page 237. To be able to silage later with the silage additives system, set the three-way stopcock (2) to position (I) "RUN". Disconnect the external water hose (2) from the pressure line (1). BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Blow compressed air through the line (1) until no more residual liquid emerges from the nozzles. Once there is no more residual liquid coming out of the nozzles, mount the line (1) on the pressure connection (2). Mount the line (5) to the compressed-air connection (3). BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 326
Blow compressed air through the line (5) until no more residual liquid emerges from the nozzles. Once there is no more residual liquid coming out of the nozzles, mount the line (5) on the pressure connection (4). Close the cover to the pump unit. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Eliminate the disturbance when an error message is displayed; see Chapter "Error list" in the supplement to the operating instructions (software). If the fault cannot be rectified, contact KRONE service partner. KMC - 520192- 19 CAN1 EQG000-034 The display shows an error message when a disturbance occurs on the machine.
There is an internal error. The values of the calibration are outside the value range. Particular instructions are required. The upper limit value has been reached. The upper limit value has been exceeded. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
A1.F5 working lights A1.F11 Moisture measurement, bale scales, silage additives unit, work- ing lights A1.F6 ISOBUS extension 23.1.3 Remedying sensor/actuator error Components must be repaired or replaced by a qualified specialist workshop only. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
The cams of the cam clutch Reduce the engine speed. are pressed out of the groove. Shut down tractor and machine and remove the crop blockage, Page 331. Reduce the driving speed. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Disturbance: The weighing device is not functioning properly. Possible cause Remedy The sensor B22 "Bale on Have the sensor B22 "Bale on chute" adjusted by a KRONE chute" has been misplaced service partner. due to excessive loads or the lowering of components.
Page 332
Have the blade lever checked/adjusted by a KRONE service partner. See manual for service technicians. The scraper comb of the Have the blade lever replaced by a KRONE service partner. blade lever does not run over the centre of the billhook.
Page 333
Have the twine disc adjusted by a KRONE service partner. See manual for service technicians. The twine disc engagement is Have the top dead centre of the knotter needle checked/ late.
Page 334
Tighten the twine brake on the lower twine strand by springs do not work properly. approx. 1-2 turns of the wing nut, Page 279. Have the knotter needle checked/adjusted by a KRONE service partner. See manual for service technicians. There is not enough knotter needle overrun in the upper dead point.
Page 335
Page 279. Not enough twine tension on the lower twine strand. Have the twine disc checked/adjusted by a KRONE service partner. See manual for service technicians. The twine disc engagement is late. Have the knotter needles checked/adjusted by a KRONE service partner.
Knot ends too short. As a result, the knot opens (usually the second knot). Possible cause Remedy 10.1 Have the clamping effect on the counter hook adjusted by a KRONE service partner. See manual for service The tension of the billhook technicians. tongue is too low. 10.2 ...
Page 337
ð The supply line from where the lubricant leaks leads to the blocked bearing point. ð Remove the blockage on the bearing. ð Tighten all outlet screw connections. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
The packer distributor block is located on the drum disc of the packer behind the side wall of the packer tray. Item Designation Large packer roll Small packer roll Main distributor block, see Page 338 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
In "rigid tandem axle" version and "MultiBale" version BP000-910 Item Designation Main distributor block, see Page 338 Pick-up pivot point on left Pick-up chain on left Drawbar eye Pick-up pivot point on right Pick-up chain on right BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 340
Pick-up chain on right Feed roller Drive chain on right In "steered tandem axle" version and "MultiBale" version BP000-911 Item Designation Main distributor block, see Page 338 Pick-up pivot point on left Pick-up chain on left BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Pick-up distributor block, see Page 339 Steering knuckle at bottom left Steering knuckle at top left Steering knuckle at bottom right Steering knuckle at top right 23.4.1.5 MultiBale distributor block In "MultiBale" version BP000-912 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Distributor block on right BP000-906 Item Designation Main distributor block, see Page 338 Needle yoke on right Knotter shaft Knotter Needle yoke on left Distributor block on left BP000-905 Item Designation Main distributor block, see Page 338 Knotter BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Note the information on the suspension points provided. Make sure the lifting means are properly secured. Never stay under the suspended machine. If work has to be performed under the machine, securely support the machine, Page 30. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 344
The car jack contact points are located on the brake axles. BPG000-151 1 Brake axle at front left 3 Brake axle at rear left 2 Brake axle at front right 4 Brake axle at rear right BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
All synthetic materials must be brought to a recycling centre for synthetic materials. Rubber • Rubber parts (hoses, tyres, …) must be brought to a rubber recycling centre. Electronic scrap • All electronic parts must be brought to a disposal point for electronic scrap. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Applying/releasing flywheel brake ....127 Attaching the hydraulic support jack....87 Automatic bale ejection ........196 Automatic call of the Road travel screen ..190 Auxiliary configuration of a joystick ....202 Auxiliary functions (AUX)........201 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 352
Changing value ..........208 Connecting spools of twine with each other ..132 Check the angle of the universally-jointed drive Connecting the camera to the KRONE ISOBUS shaft..............104 terminal CCI 800 or CCI 1200 ......124 Check wear limit on ball drawbar eye 80..295 Connecting the hydraulic hoses .......
Page 353
Description of functions of electric twine empty display for lower twine ........70 Description of hydraulic system functions ..74 Description of pick-up functions ......65 Description of twine box functions ...... 68 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 354
Index Design DS 500 ..........173 Design of display ..........170 Faults when picking up crops ......330 Design of the KRONE machine application..170 Figures ............... 11 Detail counter ........... 240 Filling the silage additives tank......321 Diagnosis driving speed/direction of travel Finishing the tying process manually ....
Page 355
Knotter distributor block........342 Knotter gearbox ..........314 Knotter shaft in rest position ....... 72 Knotter signal (Terminal) ........211 KRONE ISOBUS terminal (CCI 800, CCI 1200) ................. 168 KRONE SmartConnect (Terminal) ....249 KRONE Terminal DS 500......... 172 BiG Pack 1270...
Page 356
Menu 14-3 "Configuring main window"..... 246 Main gearbox............ 310 Menu 14-4 "Set background colour"....248 Maintenance – After the season....... 281 Menu 14-5 "KRONE SmartConnect" ....249 Maintenance – Before the season....280 Menu 14-9 “Switching Between the Terminals” 249 Maintenance - Compressor ......317 Menu 1-5 "Blowing time"...
Page 357
Operational safety: Technically sound condition 19 Overload protection on the machine ....62 Overview of fuses ..........329 Overview of gearboxes........309 Overview of silage additives unit ...... 320 Overview of the drives ........61 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 358
297 Rinsing the silage additives unit ....... 323 Road safety ............23 Road travel screen (automatic call-up)..... 190 Routing path of the central lubrication line ... 93, 94 Running actuator test ......... 31 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 359
Swivelling up the twine box hood ..... 131 Setting the bale chute........106 Swivelling up the twine box via the bale chute keypad .............. 130 Setting the bearing pressure of the crop press roller ..............276 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 360
Self-steering axle ........228 Sensitivity direction display ....216 Sensor test ..........251 Validity ..............10 Varying functions to KRONE ISOBUS terminal 175 Setting the background colour ....248 Setting the speed for blocking the self- Vehicle identification number ......60 steering axle ...........
Page 361
..............164, 193 Working lights – switching maintenance lighting on/ off ............. 163, 192 Working lights – switching rear lighting on/off . 164, Working lights – switching working lights on/off ..............163, 191 BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Page 362
This page has been left blank deliberately. BiG Pack 1270 Original operating instructions 150001367_02_en-GB...
Declaration of conformity Declaration of conformity UKCA Declaration of Conformity KRONE Agriculture SE Heinrich-Krone-Straße 10, D-48480 Spelle hereby declare, as manufacturer of the product named below, under our sole responsibility, that the Machine: Large square baler Series: BP305-10 to which this declaration refers is in compliance with the following relevant provisions of: •...
Need help?
Do you have a question about the BiG Pack 1270 and is the answer not in the manual?
Questions and answers