Page 1
600 size 1. INTRODUCTION Thank you for buying Roban Model products. The 450 size UH-1 scale fuselage is designed as an easy to use product. Please read the manual carefully before assembling the model, and follow all precautions and recommendations located within the manual. Be sure to retain the manual for future reference, routine maintenance and tuning.
Page 2
Upon assembly of the scale fuselage, the weight and complexity of the structure will increase. To mitigate risk of accidents and damages, we advise against attempting 3D flights. Skill Requirements: The operation of R/C products necessitates a certain level of skill and familiarity. Any damages or dissatisfaction resulting from accidents, modifications, or operational mishaps are not covered under any warranty.
Page 3
3. CONTENTS OF KIT Please check the contents of the kit prior to installation. CONTENTS Item No. Description Quantity Landing gear skids Landing gear struts T-connectors Redirection gearbox Rear redirection Tail skid Tail tube Washer 7x6 Gear Side windows Tail support Spacers 47mm Washer Linkage 55mm...
4. INSTALLATION Mount the struts with Screw A2x14 as shown. Install the T-connectors as shown. Install the skids as shown.
Page 6
First, mount the redirection gearbox (4) with the brackets (32) on the provided main frame (26) using Screw M3x8. Then install the original main shaft holders of your mechanism and the original tail tube holder with Screw M3x8. Then install all 9 spacers (12) with Screw M3x8 in the indicated position.
Page 7
Then dismantle the tail rotor and the linkage as shown for installation. Insert the mechanics into the fuselage as shown. Open the tail cover.
Page 8
Slide the tail onto the tail tube. 4.10 Install the tail propeller. 4.11 Screw the mechanism using the brackets (17) as shown.
Page 9
4.12 Install the tail cover. 4.13 Screw the tail as shown, using washers. 4.14 Dismantle the doors.
Page 10
4.15 Mount the cockpit as shown using epoxy adhesive. 4.16 Insert the cockpit through the rear door and glue it. 4.17 Then glue the large dashboard.
Page 11
4.18 Then glue the pilot seats. 4.19 Glue the tail units as shown. 4.20 Glue the antennas as shown.
4.21 Glue the two cable cutters as shown. 4. SPAREPART LIST 600UH1N 引擎 600 UH-1N UH600NPJ001 盖 engine cover 600 UH-1N UH600NPJ002 600UH1N 前窗 front window 600 UH-1N 600UH1N 全套 UH600NPJ003 all window 窗 600 UH-1N UH600NPJ004 600UH1N 平尾 tail wings 600UH1N 装饰...
Page 13
600 UH-1N UH600NPJ008 600UH1N 球头 ball link 600 UH-1N 600UH1N 改装 UH600NPJ009 side frame 侧板 600UH1N 改装 600 UH-1N UH600NPJ010 件 hardware set 600UH1N 升级 600 UH-1N UH600NPJ011 铁齿组 gear set 600UH1N LED 600 UH-1N UH600NPJ012 灯 light kit 600 UH-1N UH600NPJ013 600UH1N 水印...
Page 14
4. FULLY ASSEMBLED FUSELAGE Specifications: Lenght: 1460mm Height: 320mm Width: 410mm Weight: 3000g Suitable for Align TREX600 ESP and derivatives We wish you a lot of fun with the fuselage! Copyright 2024 – www.robanmodel.com...
Need help?
Do you have a question about the UH-1N and is the answer not in the manual?
Questions and answers