Download Print this page
Roban UH-1N Instruction Manual

Roban UH-1N Instruction Manual

Hide thumbs Also See for UH-1N:

Advertisement

Quick Links

Instruction manual
Scale Fuselage UH-1N
500 size
1. INTRODUCTION
Thank you for buying Roban Model products. The 500 size UH-1N scale fuselage is designed as an easy
to use product. Please read the manual carefully before assembling the model, and follow all
precautions and recommendations located within the manual. Be sure to retain the manual for future
reference, routine maintenance and tuning. The scale fuselage is designed for T-REX 500 Helicopter
series use. You can easily put it on your T-REX 500 for new clothing.
Important Note
Roban Model R/C Helicopters are advanced, high-performance devices, built incorporating the latest
technologies. They are not intended as toys, and improper use can potentially lead to serious injury,
or even fatal accidents. We implore you to read this manual thoroughly before operating these
models. Safety should be your utmost priority - not just your own, but also that of others and your
surroundings when piloting Roban Model products.
Liability Disclaimer:
The manufacturer and the seller cannot accept liability for the operation or misuse of this product.
Roban Model R/C helicopters are intended to be used exclusively by experienced adults in legally
sanctioned flying fields. Once sold, we cannot monitor or control the product's operation or usage.
Operation Guidelines:

Advertisement

loading
Need help?

Need help?

Do you have a question about the UH-1N and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Roban UH-1N

  • Page 1 500 size 1. INTRODUCTION Thank you for buying Roban Model products. The 500 size UH-1N scale fuselage is designed as an easy to use product. Please read the manual carefully before assembling the model, and follow all precautions and recommendations located within the manual. Be sure to retain the manual for future reference, routine maintenance and tuning.
  • Page 2 Upon assembly of the scale fuselage, the weight and complexity of the structure will increase. To mitigate risk of accidents and damages, we advise against attempting 3D flights. Skill Requirements: The operation of R/C products necessitates a certain level of skill and familiarity. Any damages or dissatisfaction resulting from accidents, modifications, or operational mishaps are not covered under any warranty.
  • Page 3 3. CONTENTS OF KIT Please check the contents of the kit prior to installation. Lieferumfang: CONTENTS Item No. Description Quantity Landing gear skids Landing gear struts T-connectors Redirection gearbox Rear redirection Tail skid Tail tube Servo linkage Tail shaft Tail tube Servo linkage...
  • Page 4 Base plate Tail tube holder Spacers Spacer T-lever Linkage 45mm Linkage 90mm Linkage 179mm Linkage 425mm Bracket Ball joint connectors Antenna Antenna Antenna Machine guns Glass set Rocket launcher Tail unit Side frame Screw A2x5 Screw M2.5x10 Screw A2x14 Screw M2x8 Washer M5 Washer M6 Nut M2...
  • Page 5: Installation

    4. INSTALLATION Mount the struts with Screw A2x14 as shown. Install the T-connectors as shown. Install the skids as shown...
  • Page 6 Mount the side frames, base plate, and mounting blocks as shown. Install the tail struts as shown. Install the rear redirection and the linkage as shown.
  • Page 7 Install the tail servo and adjust the tail linkage and servo. Then dismantle the tail rotor and linkage as shown for installation. Insert the mechanics into the fuselage as shown.
  • Page 8 4.10 Open the tail cover. 4.11 Slide the tail onto the tail tube. 4.12 Install the tail propeller.
  • Page 9 4.13 Screw the mechanism using the brackets (17) as shown. 4.14 Install the tail cover. 4.15 Screw the tail as shown, using the washers.
  • Page 10 4.16 Dismantle the doors. 4.17 Pre-assemble the cockpit as shown. 4.18 Insert the cockpit through the rear door and glue it.
  • Page 11 4.19 Then glue the large dashboard. 4.20 Then glue the pilot seats. Reassemble the doors. 4.21 Glue the tail units as shown.
  • Page 12: Spare Part List

    4.22 Glue the antennas in as shown. 5. SPAREPART LIST 500 UH-1A UH500APJ001 500UH1 前头 canopy 500 UH-1A UH500APJ002 500UH1 前窗 front window 500UH1 全套 500 UH-1A UH500APJ003 窗 all windows 500 UH-1A UH500APJ004 500UH1 平尾 tail wings 500 UH-1A 500UH1 脚架...
  • Page 13 6. FULLY ASSEMBLED FUSELAGE Specifications: Lenght: 1150mm Height: 280mm Width: 3300mm Weight: 1500g Suitable for Align TREX500ESP and derivatives We wish you a lot of fun with the fuselage! Copyright 2024 – www.robanmodel.com...