Page 2
User Manual PCM-3353 PC/104+ SBC w/AMD LX800/ LX600, VGA, LCD, LAN, USB2.0 and CF...
Page 3
No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. How- ever, Advantech Co., Ltd.
Page 4
Discard used batteries according to the manufacturer’s instructions. Technical Support and Assistance Visit the Advantech web site at http://support.advantech.com where you can find the latest information about the product. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance. Please have the following information ready before you call: –...
Page 5
Before setting up the system, check that the items listed below are included and in good condition. If any item does not accord with the table, please contact your dealer immediately. 1 x PCM-3353 SBC 1 x Power cable 1 x Audio cable...
For those who want superior performance for various low-power embedded applica- tions, PCM-3353 uses an AMD LX-800 processor clocked at 500 MHz, in conjunction with onboard DDR333 system memory. PCM-3353 offers convenient connector layout, easy assembly, multiple I/O, and includes single 10/100Mbps Ethernet, four USB (Universal Serial Bus) 2.0 and four...
Audio interface: Microphone in, Line in, Line out 1.3.5 OS support This board supports Win XP, Win CE and Win XPe. For further information about OS support in your PCM-3353, visit the following web resource Advantech: website: www.advantech.com or please contact tech- nical support center 1.3.6 Mechanical and Environmental Dimensions: 96 x 115 mm (3.77"x 4.05"), Mechanical Drawing (dxf file) is avail-...
Chapter Installation This chapter explains the setup procedures of the PCM-3353 hard- ware, including instructions on setting jumpers and connecting peripherals, switches and indica- tors. Be sure to read all safety pre- cautions before you begin the installation procedure.
Jumpers The PCM-3353 has a number of jumpers that allow you to configure your system to suit your application. The table below lists the functions of the various jumpers. Table 2.1: Jumper/Switch Setting Clear CMOS PCI VI/O Power Selector CN39...
Push the module into the socket until the module gently snaps in. There should only be a slight insertion force to engage the module into the contacts. Make sure that the module and the housing are aligned and locked in place. PCM-3353 User Manual...
(POST) after a reset. The PCM 3353’s BIOS standard setup menu allows you to select “All, But Keyboard” under the “Halt On” selection. This allows no-keyboard operation in embedded system applications, without the system halting under POST. PCM-3353 User Manual...
Power Connectors (CN38) 2.10.1 Main Power Connector, +5 V, +12 V (CN38) Supplies main power +5 V to the PCM-3353, and to devices that require +12 V. 2.10.2 Power Reset Button Momentarily pressing the reset button will activate a reset. The switch should be rated for 10 mA, 5 V.
2.13.3 LVDS TFT LCD Connector (CN42) Four PCM-3353 series, the board supports 1 channel 18-bit LVDS LCD panel dis- plays. 2.14 Ethernet Configuration The board is equipped with one high performance 32-bit PCI-bus Ethernet interface which are fully compliant with IEEE 802.3U 10/100Mbps standards. They are sup- ported by all major network operating systems.
Turn on the computer and check for the ìpatch codeî. If there is a number assigned to the patch code, it means that the BIOS supports your CPU. If there is no number assigned to the patch code, please contact Advantechís appli- cations engineer to obtain an up-to-date patch code file. This will ensure that your CPUís system status is valid.
Page 24
The system boot will not stop for any error. All Errors Whenever the BIOS detects a non-fatal error the system will be stopped. All, But Keyboard The system boot will not stop for a keyboard error; it will stop for all other errors. (Default value) PCM-3353 User Manual...
Page 25
Assign this boot device priority to CDROM. USB-FDD Assign this boot device priority to USB-FDD. USB-CDROM Assign this boot device priority to USB-CDROM. USB-HDD Assign this boot device priority to USB-HDD. Assign this boot device priority to LAN. PCM-3353 User Manual...
Page 26
Control copying of this block to shadow RAM. – D4000-D7FFF Shadow [Disabled] Control copying of this block to shadow RAM. – D8000-DBFFF Shadow [Disabled] Control copying of this block to shadow RAM. – DC000-DFFFF Shadow [Disabled] Control copying of this block to shadow RAM. PCM-3353 User Manual...
Page 27
This item provides flat panel adjustments. Onboard USB1.1 [Enabled] This item enables or disables motherboard USB1.1 device. Onboard USB2.0 [Enabled] This item enables or disables motherboard USB2.0 device. Onboard IDE [Enabled] This item enables or disables motherboard IDE device. PCM-3353 User Manual...
Page 28
This item allows user to adjust slave IDE mode of type for modification purpose. Suggested BIOS default value is "Auto". IDE Primary Master UDMA [Auto] This item allows user to adjust primary master IDE mode of type for modification purpose. Suggested BIOS default value is "Auto". PCM-3353 User Manual...
Page 29
Auto Flow Control [Disabled] This item allows user to control COM port auto flow transfer. Suggested BIOS default value is "Disabled". Onboard Parallel Port [378/IRQ7] This item allows user to change parallel port address. Suggested BIOS default value is "378/IRQ7". PCM-3353 User Manual...
Page 30
There are four selections for Power Management, three of which have fixed mode. Settings This item determines delay time for the watchdog timer. Min. Power Saving Minimum power management., Suspend Mode = 1 hr., and HDD Power Down = 15 min. PCM-3353 User Manual...
Page 31
This item allows user to change boot display sequence. PNP OS Installed [No] Usually best set to No. Some rare cases may need to set to Yes. Reset Configuration Data [Disabled] This item allows user to clear any PnP configuration data stored in the BIOS. PCM-3353 User Manual...
Page 32
This is to check the PC health, e.g.: current CPU temperature. Figure 3.8 PC health status screen Current CPU Temp [Show Only] This item displays current system and CPU temperature. 5 V / 12 V [Show Only] This item displays current CPU and system Voltage. PCM-3353 User Manual...
Page 33
Load Optimized Defaults Figure 3.9 Load optimized defaults screen The PCM-3353 automatically configures all setup items to optimal settings when you select this option. Optimal Defaults are designed for maximum system performance, but may not work best for all computer applications. In particular, do not use the Opti- mal Defaults if your computer is experiencing system configuration problems.
Page 34
CMOS memory of the chipset. The microprocessor checks this every time you turn your system on and compares this to what it finds as it checks the sys- tem. This record is required for the system to operate. PCM-3353 User Manual...
Page 35
3.13 Exit without Saving Figure 3.12 Exit without saving screen Selecting this option and pressing <Enter> lets you exit the setup program without recording any new values or changing old ones. PCM-3353 User Manual...
Page 36
Appendix Pin Assignments This appendix contains informa- tion of a detailed or specialized nature.
Page 38
+3.3 V (default) (3 - 4) +12 V (3 - 5) +5 V Table A.6: CN42, LVDS LCD I/F Part Number 1653910261 Footprint SPH10x2 Description *CONN. DF13-20DP-1.25V Pin Name Signal Type Signal Level NONE NONE NONE NONE PCM-3353 User Manual...
Page 39
+5 V +12 V +12 V Table A.8: CN4, TFT LCD I/F Part Number 1653920200 Footprint SPH20X2 Description *CONN. DF13-40DP-1.25V Pin Name Signal Type Signal Level +5 V +5 V +5 V +5 V +3.3 V +3.3 V PCM-3353 User Manual...
Page 40
+3.3 V +3.3 V +3.3 V +3.3 V +3.3 V +3.3 V Table A.9: CN5, Inverter Power Part Number 1655305020 Footprint WHL5V-2M Description WAFER BOX 2.0mm 5P 180D MALE W/LOCK Pin Name Signal Type Signal Level +12V +12V PCM-3353 User Manual...
Page 41
180D(M) 2.00mm Pin Name Signal Type Signal Level +3.3 V Buzzer - Buzzer + Table A.12: CN36, GPIO1 Part Number 1653010100 Footprint JH5X2S-2M Description PIN HEADER SMD 5*1P 180D(M) 2.54mm Pin Name Signal Type Signal Level +5 V PCM-3353 User Manual...
Page 42
BOX HEADER SMD 22*2P 180D(M) 2.0mm IDIOT-PROOF Pin Name Signal Type Signal Level RST# +5 V +5 V +5 V +5 V +5 V +5 V +5 V +5 V +5 V +5 V +5 V +5 V +5 V +5 V PCM-3353 User Manual...
Page 43
Part Number 1655912120 Footprint DBVGA-VF5M Description CONN. 12P 90D(F) SMD 1.25mm Pin Name Signal Type Signal Level Analog Analog Analog +5 V DDAT OD I/O +3.3 V DCLK OD I/O +3.3 V HSYNC +3.3 V VSYNC +3.3 V PCM-3353 User Manual...
Page 44
+5 V +5 V +5 V Table A.17: CN17, USB3/4 Part Number 1653005260 Footprint JH5X2S-2M Description PIN HEADER 5*2P 180D(M) 2.0mm SMD IDIOT-PROOF Pin Name Signal Type Signal Level +5 V +5 V +5 V +5 V PCM-3353 User Manual...
Page 45
-3 ~ -12 V, +3 ~ +12 V TXD4 -3 ~ -12 V, +3 ~ +12 V CTS#4 -3 ~ -12 V, +3 ~ +12 V DTR#4 -3 ~ -12 V, +3 ~ +12 V RI#4 -3 ~ -12 V, +3 ~ +12 V PCM-3353 User Manual...
Page 46
AFD# +5 V +5 V ERR# +5 V +5 V INIT# +5 V +5 V SLIN# +5 V +5 V +5 V +5 V +5 V ACK# +5 V BUSY +5 V +5 V SLCT +5 V PCM-3353 User Manual...
Page 47
Signal Type Signal Level LIN-OUT-R Analog LIN-OUT-L Analog Table A.22: CN34, AUDIO-IN Part Number 1653005020 Footprint WHL3V-2M Description WAFER BOX 2.0 mm 5P 180D w/LOCK Pin Name Signal Type Signal Level LIN-IN-R Analog LIN-IN-L Analog MIC-IN Analog PCM-3353 User Manual...
Page 48
Footprint BH5X2SV Description BOX HEADER SMD 5*2 180D (M) 2.0 mm Pin Name Signal Type Signal Level +3.3 V +3.3 V LAN2-ACTLED Analog LAN2-RX+ Analog LAN2-RX- Analog LAN2-LILED Analog LAN2-LCT Analog LAN2-LCT Analog LAN2-TX+ Analog LAN2-TX- Analog PCM-3353 User Manual...
Page 49
Part Number 1653025211 Footprint JH5X2S-2M Description HEADER 50P 90D Table A.28: CN33, Battery Connector Part Number 1655902032 Footprint WHL2V-125 Description WAFER 2P 180D(M) 1.25 mm 53047-0210 Pin Name Signal Type Signal Level +VBAT +3.3 V +5 V PCM-3353 User Manual...
Page 50
Appendix System Assignments This appendix contains informa- tion of a detailed nature.
Output_Reg EQU 01h Inversion_Reg EQU 02h Configure_Reg EQU 03h Advantech_Str db 'Advantech Company Copyright (C) 2005 Design by Dun- can',0AH,0Dh,'$' Advantech_Str db 'Advantech Company Copyright (C) 2005 Design by Dun- can, Modify by Steven',0AH,0Dh,'$' GX3_Fun_Str db 'Check Philip GPIO function.',0Ah,0Dh,'$' Note1_Str db 'Test Method: GPIO 0 connect to GPIO 1.',0Ah,0Dh,'$'...
Page 60
Note4_Str ah,09h ;=============================================================== ==== Get Number of GPIO group one group mean 8 gpio pins(one GPIO Chip) ; Input: ax=5E87h bh=00h ; output: ax=5E78 ;function success, other value means function fail cl= n group of gpio PCM-3353 User Manual...
Page 61
;function success, other value means function fail ;=============================================================== ==== ;=============================================================== ==== Get GPIO status ; Input: ax=5E87h bh=03h cl= n ; n means which group of GPIO you want to get ; output: ax=5E78 ;function success, other value means function fail PCM-3353 User Manual...
Page 62
;save NO. of GPIO chip ;1.Set GPIO 0,2,4,6 as output, GPI 1,3,5,7 as input ax,5e87h bx,02aah ;2. Set GPIO 0,2,4,6 Output Low ;restore NO. of GPIO chip push ;save NO. of GPIO chip ax,5e87h bx,0400h PCM-3353 User Manual...
Page 63
;5. Check GPI 1,3,5,7 value ;restore NO. of GPIO chip push ;save NO. of GPIO chip ax,5e87h bx,03FFh ;restore NO. of GPIO chip push ;save NO. of GPIO chip al,Fail_lenght dx, Fail_Str dx,ax bl,33h test_result al,00h PCM-3353 User Manual...
Page 64
;4. Set GPIO 1,3,5,7 Output differential ;restore NO. of GPIO chip push ;save NO. of GPIO chip ax,5e87h bx,0422h ;5. Check GPI 0,2,4,6 value ;restore NO. of GPIO chip push ;save NO. of GPIO chip ax,5e87h bx,03FFh PCM-3353 User Manual...
Page 65
;1.Set GPIO 0,2,4,6 as output, GPI 1,3,5,7 as input test_result: ah,09h next_test Finish_Test: popa .exit ;============================================================== ;Input : CL - register index CH - device ID ;Output : AL - Value read ;============================================================== Ct_I2CReadByteProcNear push cx mov dx,SMBus_Port +04h mov al,ch ;ID cmd(read) dx,al NEWIODELAY PCM-3353 User Manual...
Page 66
;Data0 NEWIODELAY NEWIODELAY Ct_I2CReadByteEndp ;============================================================== ;Input : CL - register index CH - device ID AL - Value to write ;Output: none ;============================================================== Ct_I2CWriteByteProcNear push ax push cx mov dx,SMBus_Port +04h mov al,ch ;ID cmd(Write) dx,al PCM-3353 User Manual...
Page 67
Delay5ms mov cx, 100h newiodelay loop short @B call CT_Chk_SMBus_Ready Ct_I2CWriteByteEndp CT_Chk_SMBus_ReadyProcNear mov dx,SMBus_Port + 0;status port mov cx,0800h Chk_I2c_OK: al,dx ;get status NEWIODELAY dx,al ;clear status NEWIODELAY test al, 02H ;termination of command ? short Clear_final PCM-3353 User Manual...
Page 68
1000 NEWIODELAY loop short @B pop cx Delay5ms ENDP Phoenix_debuger proc near pushf push cx push offset PhdebugRetAddr push cs push cs db 0EAh dw 0013h dw 0DA00h PhdebugRetAddr: popf Phoenix_debuger endp ;=============================================================== ==== Program END PCM-3353 User Manual...
Page 69
;=============================================================== ==== PCM-3353 User Manual...
Need help?
Do you have a question about the PCM-3353 and is the answer not in the manual?
Questions and answers