Specifications; Time Ranges; Ratings - Omron H3DS Manual

Specifications

■ General
Item
Operating mode A: ON-delay (Signal or Power)
B: Flicker OFF start (Signal or Power)
B2: Flicker ON start (Signal or Power)
C: Signal ON/OFF-delay
D: Signal OFF-delay
E: Interval (Signal or Power)
G: Signal ON/OFF-delay
J: One-shot (Signal or Power)
Input type Voltage input
Output type Relay: SPDT
External connections Screw terminal, Screw-Less Clamp
Terminal block
Screw terminal type:
Screw-Less Clamp type: Clamps two 1.5-mm
Terminal screw 0.98 N·m max.
tightening torque
Mounting method DIN track mounting (see note)
Attachment Nameplate label
Approved standards UL508, CSA C22.2 No.14
Conforms to EN61812-1, IEC60664-1 4 kV/2, VDE0106/P100
Output category according to IEC60947-5-1 (AC-13; 250 V 5 A/AC-14; 250 V 1 A/AC-15; 250 V 1 A/DC-13; 30 V 0.1 A/
DC-14; 30 V 0.05 A)
Note: Can be mounted to 35-mm DIN Track with a plate thickness of 1 to 2.5 mm.

■ Time Ranges

Time scale display
0.1 s
1 s
0.1 m
1 m
0.1 h
1 h
10 h
Note: When the time setting dial is set to "0" for any time scale, the output will operate instantaneously.

■ Ratings

Rated supply voltage
(see notes 1 and 2)
Operating voltage range
Power reset
Reset voltage
Power consumption (see note 3)
Voltage input
Control output
Ambient temperature
Ambient humidity
Note: 1. DC ripple rate: 20% max.
2. Since an inrush current of 0.5 A will occur when using the power supply voltage at 24 VDC, pay careful attention when turning on or off
the power supply to the Timer with a solid-state output such as a sensor.
3. The power consumption is for mode A after the Timer counts the time-up time and for the AC input at 50 Hz. The power consumption of
the H3DS-ML includes the input circuit with the B1 and A1 terminals short-circuited.
H3DS-ML@
Clamps two 2.5-mm
Time range
0.1 to 1.2 s
1 to 12 s
0.1 to 1.2 min
1 to 12 min
0.1 to 1.2 h
1 to 12 h
10 to 120 h
24 to 230 VAC (50/60 Hz)/24 to 48 VDC
85% to 110% of rated supply voltage
Minimum power-off time: 0.1 s
2.4 VAC/DC max.
AC: 32 VA max./3.0 W max. (typical: 30 VA/2.7 W) at 230 VAC
14 VA max./2.2 W max. (typical: 13 VA/2.1 W) at 100 to 120 VAC
DC: 0.7 W max. (typical: 0.6 W) at 24 VDC
1.4 W max. (typical: 1.3 W) at 48 VDC
Max. permissible capacitance between inputs lines (terminals B1 and A2): 2,000 pF
Load connectable in parallel with inputs (terminals B1 and A1).
H-level: 20.4 to 253 VAC/20.4 to 52.8 VDC
L-level: 0 to 2.4 VAC/DC
Contact output: 5 A at 250 VAC with resistive load (cos = 1)
5 A at 30 VDC with resistive load (cos = 1)
Operating: –10 C to 55 C (with no icing)
Storage: –25 C to 65 C (with no icing)
Operating: 35% to 85%
Solid-state Multi-functional Timer
H3DS-SL@
A: ON-delay
B2: Flicker ON start
E: Interval
J: One-shot
---
2
max. bar terminals without sleeves.
2
max. bar terminals without sleeves.
H3DS-AL@
A: ON-delay (fixed)
H3DS-M/-S/-A
B-13