Learning Function - THOMSON ROC 740 Manual

Roc740_GB 25/04/01 16:05

Learning function

How does this work?
Where you cannot find the right code for your equipment item, or one does not exist in the separately-supplied list, you can have your
learn the functions controlled and commanded by the original item's remote control, by way of the equipment mode (
ROC 740
,...) you want to operate. To do this you download key function one-by-one to your
SAT
to keys as you wish.
Your can learn up to 3 different remote controls having up to 50 keys each. In order that utilization is not too complicated we
ROC 740
recommend you only memorize one only remote control operation to be called by each mode key (
entered an equipment item code under a certain mode you can add other function controls by using other non-assigned keys on your
ROC 740.
Before starting:
1. Make sure your
ROC 740
is not lit by neon tube or energy-saving lamps. Emissions from such lighting will interfere with the download operation.
2. Erase any existing codes by a reset. Follow the instructions on Page 5.
3. Place the 2 remote controls on a flat surface, facing each other and less than 5 cms (2 inches) apart. Make sure the infrared-
emitting surfaces of the 2 remote controls are directly facing each other (see diagram).
4. Start by downloading 2 or 3 key function controls from the item's original remote control and then check that your
learned them, by trying it out with the item. If this was OK, proceed to downloading the other key functions you want from the
item's original remote control.
Note: When the memory is saturated "Full" will blink on the display for a few seconds. At such time you cannot download other key
functions, unless you re-assign those key functions you already downloaded. If you try to download a prohibited 4th remote control
you will get the display:' "Error".
It can take a few seconds to download each key function control. Make sure you keep the key you are downloading from the original
item's remote control firmly pressed, until you get the display "Ok" on your
Code downloading from other remote controls
Always place the two remote controls facing each other with their IR-emitting panels close to each other and aligned (see diagram).
1. Press the key (
SET UP
2. Release the key.
SET UP
3. Press several times on the
4. Press the mode key (
TV
item's remote control that you want to download. "Key ?" will then display on the LCD
panel of your
ROC 740.
5. Press any key (eg.
1),
the code for that key function from the item's original remote control (to make a " Shift "
to another function first press the
Do not program the mode keys (
6. Keep the key ( in the above example) of your item's original remote control pressed for a
1
few seconds to transfer and store its correct code to your
"Key ?" if the correct code has been stored in your
If you get the display "Error" this indicates the transfer failed. In such case repeat
procedures 5 and 6, above.
7. Repeat procedures 5 and 6 until all the key functions to download are stored in your
8. When you have finished all downloading press the -/-- key (
9. You have now finished downloading, your
Erasing codes for any particular mode (TV, VCR, SAT, etc.)
If you want to download another remote control, for example under "TV", you can erase all previous controlled functions and key
settings learnt for that particular mode.
1. Hold down the
SET UP
2. Release the key.
SET UP
3. Press the key several times until "Clear" (erase) displays.
SET UP
4. Press the mode key (
TV
codes you want to erase and then validate by
5. This will erase all stored controls in that mode.
6. Erasure is now finished. Your
Erasure of all stored codes (reset)
Before programming your
ready to initialize.
1. Hold down the
SET UP
2. Release the key.
SET UP
3. Press the key several times until "Reset" displays.
SET UP
4. Press briefly on the
OK
5. Make another validation with the
6. Your is now reset and will display the day and time.
ROC 740
Page 5
and the equipment item's original remote control both have new batteries and that the room you are in
) until you get the "Setup" display on the LCD display.
17
key until "Learn" displays.
SET UP
, , , etc...) for the remote control function on the original
VCR SAT
giving the display "Learn", and the
key).
S
, , , ...) and the
TV VCR SAT
ROC 740
will display the day and time.
ROC 740
key ( ) until "Setup" displays on the LCD panel.
17
, , , etc...) for the equipment item whose function
VCR SAT
.
OK
will display the day and time.
ROC 740
the first time make sure any stored codes have been erased, in order to have the remote control
ROC 740
key ( ) until "Setup" displays on the LCD panel.
17
key and "Confirm" will display.
key.
OK
ROC 740
's LCD panel.
ROC 740
will now "copy"
ROC 740
keys.
SET UP
. The LCD panel will display
ROC 740
.
ROC 740
).
27
5
TV
allowing you to assign control functions
, , ,...). If you have already
TV VCR SAT
ROC 740
Learn
Mode ?
Learn
TV
Key ?
.
TV
Setup
Mode ?
Clear
Mode?
Setup
Mode ?
Reset
Fr 12:48
, ,
VCR
has