Learning Function - THOMSON ROC8209 Operating Instruction

k. TIMER X EING2 is displayed. Press and release the second key required. If only two keys are required, press
and release Okay at this point – go to Step "m" below.
l. TIMER X EING3 is displayed. Press and release the third key required.
m. FERTIG will be displayed and the remote will remain in Setup, returning to the CODE SETUP screen.
Set the remote control down on a table or fl at surface at the level of the TV set's infrared receiver with its front end
pointed toward the device to be controlled.
Press and release the Exit key at any time during the Setting to return to normal operation.
a. Press and hold Setup key until CODE SETUP is displayed (takes approximately 2–3 seconds).
b. Release Setup key.
c. Navigate to TIMER SETUP by pressing the Setup key 2 times. Press and release Okay key.
d. SLEEPTIM.TV is displayed.
e. Navigate to the desired TIMER X SETUP (where "X" is 1, 2, 3 or 4) screen. Press and release the Okay key.
f. TIMER X AUS is displayed. Press and release the Okay key.
g. US BEST. is displayed. Press and release the Okay key.
h. FERTIG will be displayed and the remote will remain in Setup, returning to the CODE SETUP screen.
If the make of the device you wish to control is not in the separate code list or if some functions are missing in the
code you have programmed, you can copy the key functions of the original remote control of the device into your
LCD remote control. Depending on the format of the transmission codes of the original remote control, your LCD
remote control can memorise up to 150 keys.
Tips On Learning:
• Where possible, use of fresh batteries for both remotes is recommended.
• Only one original remote type can be learned per individual Mode.
• Clear all learned commands (Loeschen Alles) before attempting any Learning.
• Experiment by Learning 2 or 3 keys initially (to ensure compatibility and familiarity) and then Clear all learned
commands (Loeschen Alles) before completely Learning your original remote's keyboard.
• Carry out a "Mode Clear" (Loeschen Modus) before learning a Mode to make sure there are no previously
learned commands for that Mode.
• Place the remotes end-to-end so the IR LED's on both remotes are directly in line with each other. You may need
to adjust the height of either remote to achieve this.
• Keep the distance between the two remotes to approximately 25 mm.
• Do not move or change the distance between the two remotes while learning all the required keys for that
Mode.
• Do not attempt to Learn directly under an incandescent or low-energy light as these can cause interference with
the IR transmissions. Keep at least one metre away from any such light sources.
• Avoid learning the Volume/Mute keys on your original remote unless you are sure these operate the same
target device e.g. some original DVD remotes also include TV Volume/Mute key control – these can be two
different types of code.
• Avoid learning the VCR keys on your original remote unless you are sure these operate the same target device
e.g. some original TV remotes also include VCR key control – these can be two different types of code.
• Learning a key can take up to 3 seconds. Do not release the key being Learned until the FERTIG or
LERNEN FEHL. screens have been displayed.
• If learning the first or second keys for a Mode results in continuous errors then try the following:
i. End the Learn session by pressing the Exit key.
ii. Clear out the learned commands for that Mode.
iii. Check the IR LEDs are correctly aligned between the two remotes.
iv. Adjust the distance between the two remotes to be closer (e.g. 15mm) or further away (e.g. 50mm) from
each other.
v. Try learning the original remote for that Mode again.
If the problem occurs again with the same key check the original remote key being learned – does it transmit?
Does it operate the target device? Try learning that key under a different clear Mode. If it learns okay then it is
likely to be a different code type from the others and cannot be learned under the same Mode.
Notes:
1. You cannot learn under the Setup or Macro keys.
2. All learned commands for a Mode are deleted if the same or a new 4-digit code is entered for that Mode
(includes Direct Code Entry, Code Search and Brand Search entries).
3. The Backlighting is turned off for Learning.
To clear a Timer ("Timer Bell" in normal display)

Learning function

16