Supervisor Parameters - Parker ATT Plus-E User Manual

SUPERVISOR PARAMETER
MODBUS VARIABLES
The Modbus on refrigeration dryer PSE is Modicon standard (so 1-based addresses).
All the variables are access as Holding register (Modbus function FC03, 40000).
As standard configuration, RS-485 baudrate = 38400, 8bit,Parity = Even, stop bit = 1 address =1,
you can change it by the touch screen.
BMS Description
Address
8960 Modbus ON/OFF - enabling / disenabling bit
8961 Discharge temperature
8962 Dew point temperature
8963 Suction temperature
8964 Evaporation temperature
8965 Temperature
8966 drain pressure
8967 Colm 1 air pressure
8968 Colm 2 air pressure
8969 Dew point (press? temp.?)
8970 Resistor temperature Col 1
8971 Resistor temperature Col 2
8972 Regeneration end temperature
8973 reserved variable
8974 Hgh pressure switch State
8975 Low pressure switch State
8976 Remote input ON/OFF stato
8977 Alarm reset
8978 Sequence phase monitoring
8979 Integral protection status of the compressor
8980 Thermal state of the resistor
8981 Output resistor control percentage power
8982 comand open Bypass (if present)
8983 bypass limit switch Y7 open state (if present)
8984 bypass limit switch Y7 close state (if present)
8985 Darin condenser valve COMAND open
8986 electrical current input (se presente)
8987 Suction pressure
8988 Bypass open Y7 (in)
8989 reserved variable
8990 Condenser livel sensor state
8991 status of alarm (Word)
8992 status of alarm (Word)
8993 status of alarm (Word)
8994 status of alarm (Word)
8995 status of alarm (Word)
8996 status of alarm (Word)
8997 status of alarm (Word)
8998 status of alarm (Word)
8999 status of alarm (Word)
9000 status of alarm (Word)
9001 status of alarm (Word)
9002 status of alarm (Word)
9003 status of alarm (Word)
9004 status of alarm (Word)
9005 status of alarm (Word)
Type "Read/ Variable name
Write"
BOOL RW xC_OnOff_lc
INT R i_B8
INT R i_B0
INT R i_B5
INT R i_B2
INT R i_B3
INT R i_P1
INT R i_P01
INT R i_P02
INT R i_PDP
INT R i_R11
INT R i_R12
INT R i_R2
BOOL R N.A.
BOOL R x_A_HPressS
BOOL R x_A_LPressS
BOOL R x_C_OnOff
BOOL R x_AlmReset
BOOL R x_A_PHS
BOOL R x_A_PIS
BOOL R x_A_THS
INT R oi_THpid_out
BOOL R ox_C_Bypass
BOOL R x_C_LswOpen
BOOL R x_C_LswClose
BOOL R ox_C_Drain
INT R i_TA
INT R i_P2
BOOL R ix_C_Bypass
BOOL R N.A.
BOOL R x_CS1
UINT R AlarmMain_1
UINT R AlarmMain_2
UINT R AlarmMain_3
UINT R AlarmMain_4
UINT R AlarmMain_5
UINT R AlarmMain_6
UINT R AlarmMain_7
UINT R AlarmMain_8
UINT R AlarmMain_9
UINT R AlarmMain_10
UINT R AlarmMain_11
UINT R AlarmMain_12
UINT R AlarmMain_13
UINT R AlarmMain_14
UINT R AlarmMain_15
ATT+ 060-090
9006 status of alarm (Word)
9007 status of alarm (Word)
9008 status of alarm (Word)
9009 status of alarm (Word)
9010 status of alarm (Word)
9011 status of alarm (Word)
9012 status of alarm (Word)
9013 status of alarm (Word)
9014 status of alarm (Word)
9015 status of alarm (Word)
9016 status of alarm (Word)
9017 status of alarm (Word)
9018 status of alarm (Word)
9019 status of alarm (Word)
9020 status of alarm (Word)
9021 status of alarm (Word)
9022 status of alarm (Word)
UINT R AlarmMain_16
UINT R AlarmWarning_1
UINT R AlarmWarning_2
UINT R AlarmWarning_3
UINT R AlarmWarning_4
UINT R AlarmWarning_5
UINT R AlarmWarning_6
UINT R AlarmWarning_7
UINT R AlarmWarning_8
UINT R AlarmWarning_9
UINT R AlarmWarning_10
UINT R AlarmWarning_11
UINT R AlarmWarning_12
UINT R AlarmWarning_13
UINT R AlarmWarning_14
UINT R AlarmWarning_15
UINT R AlarmWarning_16
13