Download Print this page
CDN DTP572 Quick Start Manual

CDN DTP572 Quick Start Manual

Dual probe thermometer

Advertisement

Quick Links

FOR MONITORING TEMPERATURES
WHILE COOKING
Monitors temperature while cooking
Displays actual temperatures of both probes
Audio/visual alerts when food is done
Waterproof (IPX5)
2.5 mm reduced tip
Accuracy: ±2°F (1°C)
Programmable
Backlit extra-big digits
On/off button
Auto-off
Selectable units
Temperature guide
4" (11.2 cm) probes
3' (91.4 cm) high heat sensor cables (heat resistant
up to 572°F (300°C) for 3 hours)
2-way mounting: magnet, stand
Rechargeable battery, charging cable & instructions
included
Note:
Remove label from display before initial use.
Clean the thermometer stem before each use.
Tel 800 338-5594 Fax 800 879-2364 Web CDNmeasurement.com
DUAL PROBE THERMOMETER
Note:
In the following instructions, names of the control
buttons are shown in CAPS. Function information that
appears on the display is shown in BOLD CAPS. The
buttons on this thermometer are touch buttons which do
not require strong pressure.
CHARGING THE BATTERY
The red BATTERY ICON (
when battery status is low (below 3.3V) and needs to
be charged. The battery is built-in and does not need
to be replaced. Under normal working conditions, the
battery icon does not appear on the display.
1. Insert the USB-C plug into the jack on the left side
of the case. Insert the USB-A plug into a USB-A
power source (5V/1A).
Note:
Use only an original CDN charging cable. The use of
another cable is subject to approval by CDN.
2. The red BATTERY ICON (
display while charging. Allow the thermometer to
charge for 1-2 hours.
Model: DTP572
-58 to +572°F/-50 to +300°C,
) appears on the display
) appears on the

Advertisement

loading
Need help?

Need help?

Do you have a question about the DTP572 and is the answer not in the manual?

Questions and answers

Susan McGovney
April 20, 2025

I put in Celsius and cannot get it back to farenheit

1 comments:
Mr. Anderson
May 10, 2025

To convert Celsius to Fahrenheit on the CDN DTP572, press and hold the POWER ( ) button for 2 seconds to turn the thermometer on. The default unit is Fahrenheit (°F). To change the unit, follow the user manual instructions, which typically involve accessing the settings mode and selecting the desired unit (°F or °C). Exact button steps for unit conversion are not detailed in the provided context.

This answer is automatically generated

Subscribe to Our Youtube Channel

Summary of Contents for CDN DTP572

  • Page 1 Insert the USB-A plug into a USB-A power source (5V/1A). Note: Use only an original CDN charging cable. The use of another cable is subject to approval by CDN. 2. The red BATTERY ICON ( ) appears on the display while charging.
  • Page 2 P1 Set Temp after 5 seconds of inactivity. G. Error Messages 1) When the P1 set temperature is flashing, The DTP572 incorporates visual diagnostic press the UP () or DOWN () button messages as follows: to enter desired temperature from -58 to +572°F (-50 to +300°C).
  • Page 3 Restart the thermometer. If the error message remains, please contact CDN for • Do not use the probe in a microwave oven. further assistance. • Always read the user manual thoroughly before operating.
  • Page 4 238–244°F 232–238°F 227–233°F replaced without charge upon receipt of the unit prepaid Hard Ball 246–264°F 240–258°F 235–253°F at: CDN, PO Box 10947, Portland, OR 97296-0947 USA. This warranty does not cover damage in shipment or Soft Crack 266–286°F 260–286°F 255–275°F failure caused by failure to adhere to the accompanying Hard Crack 296–306°F 290–300°F 285–295°F...