Chapter 11. List Of Functions; Listok Performance Parameters Semen Scisvasenapicnscvstaaxtatsbatmnndateuelaaans Doh Sigih Goa Dhunssoqsneeateeeueeet Ass; Sethi Deo Ule 5 Ciccaces2Cuuis Ed Causinns Ids Avees Aexexee Oaceavackanis Dale Tattton Ian Maal Anita Ses Aa Ag Hates Eaeaataas; Settings Common To The Entire Performance (Per Fori Comiion) Isis Cadaicedscdshavfiassainiasdenatieateaeauaziaedes - Roland XP-10 Owner's Manual

Chapter 11. List of functions
The XP-10 allows you to make detailed settings for a
large number of functions, as has been explained in
chapters 1-10. Chapter 11 gives a complete list of all
available functions on the XP-10.
* Functions which were already explained in chapters
1-10 will not be explained in detail in this chapter.
For details refer to the appropriate section in chap-
ters 1-10.
List of Performance parameters
The settings that are stored as part of a Performance
can be grouped in two categories; "Common" settings
which are common to all Parts, and "Part" settings
which are made for each Part.
Setting procedure
1. Press [EDIT].
The indicator will light.
2. Use VALUE[-]/[+] to select "Perform Common"
or "Perform Part" and press [ENTER].
3. Press a numeric key [6]-[0} several times to select
the function whose setting you wish to change.
* If you hold down [ENTER] while you press [6]-[0],
you will return to the previous item.
* To make settings for different Parts, use PART [~@]
/[ b> ] to select the Part. You will be able to select
only two Parts (Upper Part and Lower Part) if the
Keyboard Mode (p.19) is set to Dual, X-dual, or
Split.
4. Use VALUE[-]/[+] to set the value.
* If you wish to make settings for other functions,
repeat steps 3-4.
* If you wish to make settings for other Parts, repeat
steps 3-4.
5. Press [EDIT].
The indicator will go out, and the previous display
will reappear.
Settings common fo the entire
Performance (Perform Common)
Sound-related settings ([6]: LEVEL/EFFECT)
Volume setting (Level)
Setting: 0-127
Set the volume of the entire Performance.
Chorus type (CHORUS Type)
Setting: CHORUS1-4, FBK CHORUS, FLANGER,
SHORT DELAY, S DELAY FB
("Selecting the Chorus/Reverb type" p.25)
Chorus depth (CHORUS Level)
Setting: 0-127
("Adjusting the Chorus/Reverb depth for the Tones
of all Parts" p.25)
Reverb type (REVERB Type)
Setting: ROOM1-3, HALL1-2, PLATE, DELAY, PAN
DELAY
("Selecting the Chorus/Reverb type" p.25)
Reverb depth (REVERB Level)
Setting: 0-127
("Adjusting the Chorus/Reverb depth for the Tones
of all Parts" p.25)
MIDI-related settings ([7]: MIDI)
Transmit Channel selection (Tx Channel)
Setting: PART, 1-16
("Set/check the Keyboard Transmit Channel" p.45)
Tone Change Receive Switch on/off (Rx Tone
Change)
Setting: ON, OFF
("Turn on the Tone Change Receive Switch" p.45)
Keyboard settings ([8]: KEYBOARD)
Transposition amount (Transpose)
Setting: -24-+24
("When to use transposition (Transpose and Key
Shift)" p.27)
Split point (Split Point)
Setting: C2-C#7
("Playing two Tones from the keyboard (Keyboard
Mode)" p.19, "Setting the Split Point" p.20)
Upper Part (Upper Part)
Setting: 1-16
("Selecting Parts" p.19)
Lower Part (Lower Part)
Setting: 1-16
("Selecting Parts" p.19)
Control settings ([9]: CONTROL)
X-dual controller selection (X-DUAL Ctr)
Setting: PEDL, MOD, SLDE
("Changing the X-dual controller" p.20, "About the
XP-10's controllers" p.30)
59