Roland XP-10 Owner's Manual page 83

Chapter 12. Appendix
Remar a8 EE I MEAP EE IAI LEN ic AES RE ETT TT EI
© Portamento {Controller number 65)
Status 2nd byte ard byte
Bn 41H wH
n=MIDI channel number
vv=Control value
:QH - FH {ch.] - ch.16)
2 OOH - 7FH (0-127) 0-63=OFF 64-127<ON
* Transmitted when Porta Time will be switched OFF/1-127.
© Sostenuto (Controller number 66}
Status 2nd byte 3rd byte
8nH 42H vH
n=MIDI channel number
vv=Control value
10H - FH (ch.J - ch.16)
: QOH - 7FH (0-127) 0-63=OFF 64-127=ON
© Soft {Controller number 67)
Stajus 2nd byte Sed. byte
BaH 43H vvH
n=MIDI channel number
vv=Control value
2H - FH (ch.1 - ch.16}
2 00H - 7FH (0- 127) 0-63=OFF 6$-127=0N
© Portamento control {Controller number 84}
Status 2nd byte and byte
BnH 54H hkH
n=MIDI channel number
kkesource note number
0H - FH (ch.} - ch.16)
+ OOH - 7FH (0-127)
© Effect 1 (Reverb Send Level)
Status zad byte Andhyte
BoH 5BH vwH
(Controller number 91)
n=MIDI channel number
vveControl value
20H - FH (ch.] - ch.16)
: 00H - 7FH (0- 127) Initial value = 28H (40)
* This message is transmitted when "Send GS/General MIDI Setup" is executed,
O Effect 3 (Chorus Send Level) (Controller number 93)
Status andbyte ded. byte
BnH 5DH vwH
n=MIDI channel number + OH - FH (ch.3 - ch.16)
vv=Contml value 2 OOH - 7FH (0 - 127) Initial value = QOH (0)
* This message is transmitted when "Send GS/General MID} Setup" is executed.
(O NRPN MSB/LSB (Controller number 98,99)
Status 2nd byte 3rd byte
8nH 63H mmH
BnH 62H UH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
mm=upper byte of the parameter number specified by NRPN
H=lower byte of the parameter number specified by NRPN
* This message is transmitted when tone change is made on the panel or "Send GS/General MIDI Setup" is
executed.
"NRPN
XP-10 transmits NRPN with Bank select and program change correspanding to the tone when tone change
is made.
However, NRPN is not transmitted when "User Bank Select Tx = ON".
NRPN Data entry
MSBLSB SB Description
OFH 08H mmH Vibrato rate {relative change on specified channel)
mm: (EH - 40H - 72H (-50 - 0 - +50)
01H 09H mn Vibrato depth {relative change on specified channel)
mm: 0EH - 40H - 72H -50 - 0 - +50)
OIOAHL = mmH Vibrato delay (relative change on specified channel)
mmm: OEH - 40H - 72H (-50- 0+ +50)
O1H 20H. mmH TVF cutoff frequency (relative change on specified channel)
mm: DEH - 40H - SOH (-50 - 0 - +16)
OLH 21H mmH TVF resonance (relative change on specified channel)
mm: 0EH - 40H - 72H (-50 - 0 - +50)
O1H 63H mmH TVFATVA Env. Attark time (relative change on specified channel)
mm: QEH - 40H - 72H (-50 - 0- +50)
DVH 64H mmH TVF&TVA Env. Decay time (relative change on specified channel)
mmm: OEH - 40H - 72H (-50- 0 - +50)
O1H 66H nunH TVF&TVA Env. Release lime {relative change on specified channel)
mm: 0EH - 40H - 72H (-50 - 0 - +50)
* Data entry LSB is ignored.
© RPN MSB/LSB {Controller number 100,101)
Status 2nd byte 3ed byte
BnH 65H mmH
BnH 64H 1
n=MIDI channel number 2 OH - FH (ch. - cht6)
mme=upper byte of parameter number specified by RPN
{l=lower byte of parameter number specified by RPN
* This message is transmitted when tone change is made on the panel or "Send GS/General MID! Setup" is
executed.
"REN
XP-10 can transmit Pitch bend sensitivity and RPN null.
RPN Data entry
MSB LSB MSB L5B Explanation
00H 00H: mmH ~ Pitch Bend Sensitivity
mm: 00H - 18H (0-24 semitones) _ Initial value = 02H (2 semitones)
7FH 7FH —— RPN null
Return to disable condition.
O Ext Control Number
Status andbyte aed byte
Ba ccH wH
n=MIDI channel number
ce=Control change number
pp=Program number
20H - FH (ch.1 - ch.16)
1H - 1FH,40H - 5FH (1 - 31,64 - 95)
: 00H - 7FH (0-127)
* Designated the contro! change number transmitted with slider],2 and pedal.
@ Program Change
Status and byte
CnH ppH
n=MIDI channel number
ppeProgram number
20H - FH (ch. - ch.16)
:00H - 7FH (prog. - prog.128)
* This message is transmitted when tone change is made on the panel or "Send GS/General MIDI Setup" is
executed,
@ Pitch Bend Change
Status 2nd byte ard byte
Enit Ut mmH
n=MIDI channel number
mm}l=Pitch Bend valuc
OH - FH (¢h.1 - ch. 16)
00 OOH - 40 OOH - 7F 7FH (-8192 -0 - +8191)
* This message is transmitted when the Pitch Bender is operated. However,Pitch Bend Change is not trans-
mitted when the PALETTE SELECT button on the panel is turned on.
@ Channel Mode Messoges
@ Al! Sounds Off (Controller number 120)
Status 2nd. byte aed byte
Bait 76H 0K
n=MIDI channel number '0H - FH {ch.1 - ch.16)
* This message is transmitted when used to change part or MIDI receive channel.
@ Reset All Controllers (Controller number 121)
Status 2nd byte dud byte
Bn 7OH 00H
n=MIDI channel number 20H - FH (ch.1 - ch.26)
* This message is transmitted when used to change part or MIDI receive channel.
@ Ail Notes Off (Controller number 123)
Status 2nd byte 3rd byte
BaH 78H 00H
n=MIDI channel number + OH - FH {ch.) - ch.16)
* This message is transmitted when used to change part or MIDI receive channel.
® MONO {Controller number 126)
Status Zod byte dd byte
Bai 7EH mmH
n=MIDI channel number
mm=mono number
: OH - FH (ch.1 - ch.16)
2 00H - 10H (0 - 16)
* This message is transmitied when the Salo Switch is ON.
@ POLY (Controller number 127)
Status and byte ard byte
Ba FH 00H
n=MIDI channel number QH - FH {ch.i - ch.16}
* This message is transmitted when the Solo Switch is ON.
@ System Realtime Message
@ Start
Status
FAH
* Whenever press "SEQ CTRL."on the panel{ransmitted alternately "Start" and "Stop".
® Stop
Stntus
FCH
* Whenever press "SEQ CTRL"on the panel,transmitted alternately "Start" and "Stop"
83