Table of Contents
Advertisement
Chapter 12. Appendix
@ Active sensing
Status
FEH
* This will be transmitted constantly at intervals of approximately 250ms.
@ System exclusive messages
@ System exclusive messages related to mode settings
© Turn General MIDI System On
'Status
Data byte
'Status
FOH
7EH, 7FH, 09H, 01H
FH
Byte
Explanation
FUR
Exclusive status
7EH
ID number
(Universal Non-realtime Message)
7FH
Device 1D
(Broadcast)
OOH
Sub IDA1
(General MIDI Message)
O1H
Sub 1D#2
{General MIDI On)
FH
EOX
(End Of Exclusive)
* This message is transmitted when "Send General MIDI Setup" is executed.
© GS reset
Status
Data byte
'Status
FUH
AHL dev, 42H, 12H, 40H. 00H, 7FH, 00H, 41H
F7H
Byte
Explanation
FOH
Exclusive status,
41H
TD number
(Roland)
dev
Device [D
(dev: OOH - FH (1 - 32)
Initial value is 10H(17))
QH
Model 1D
(GS)
12H
Comunand ID
(DT1)
40H
Address MSB
OOH
Address
7FH
Address LSB
OOH
Data
(GS reset)
4H
Checksum
Patt
BOX
(End Of Exclusive)
* This message is transmitted when "Send GS Setup" is executed,
@ Universal Non-realtime System Exclusive Messages
© Inquiry reply
Status
Status
FOH
7EH,dev,06H,02H.41H,42H,00H,02H,01H,09H,01H,00H,00H
F7H
Butz
FOH
Exclusive status
7EH
1D number
(Universal Non-realtime Message)
dev
Device 1D
{dev: OOH - TFH (1 - 32)
Initial vatue is 10H(17))
06H,02H
Inquiry reply
41H
ID number
(Roland)
42H,00H
Device Family Code
02H,01H
Device Family Number Code
OSH,OTH,DOH,UOH = Software Revision Level
F7H
EOXx
(End Of Exclusive)
* When Inquiry Request is received, Inquiry reply Message will be transmitted.
* Regarding the Inquiry Request, please refer to page 62.
@ Data transmission
When an appropriate "Data Request 1 (RQU)" message is received, the requested internal data will be trans-
mitted,
© Data set 1
DTi
Status
Data byte
Status
FOH
41H, dev, 42H, 12H, aaH, bbH, ccH, ddl, ... eeH, sum
F7H
Byte
Explanation
FOH
Exclusive status
SIH
ID number
(Roland)
dev
Device ID
(dew: OOH - 1FH (1 - 32)
Initial value is 10H(17))
mod
Model 1D
(mod: GS=42H, XP-1U=7BH)
RH
Command ID
(DT?)
aaH
Address MB: upper byte of the starting address of the data to be sent
bbH
Address
: middle byte of the starting address af the data to be sent
ccH
Address LSB: lower byte of the starting address of the data to be sent.
ddH
Data
: the actual data to be sent. Multiple bytes of data are transmitted in order
starting from the address.
eeH
Data
sum
Checksum
F7H
EOX
(End Of Exclusive)
* The amount of data that can be transmitted at one time depends on the type of data, and data will be trans-
mitted from the specified starting address and size. Refer to the Address and Size given in Section 3 (Page
BA).
* Data larger than 128 bytes will be divided into packets of 128 bytes or less, and each packet will be sent at
an interval of about 40ms.
* Regarding the checksum pivase refer to section 4 (Page 91).
84
Section 3. Parameter Address Map
This map indicates address, size, Data (range), Parameter, Description, and Default Value of parameters
which can be transferred using "Reques! data 1 (RQ1)" and "Data set 1 {DT1)"
All the numbers of address, size, Data, and Default Value are indicated in 7-bit Hexadecimal-form.
@ Address Block mep
An outlined address map of the Exclusive Communication is as follows;
<XP-10 (Model {D=7BH) >
Address (H)
Block
100000
+
es
2
re
1 SYSTEM SETUP PARAMETERS
' Butk
10.00 2B +
+
OVO
+
—__—__—-
—+
1 USER PERFORMANCE PARAMETERS
QROR PR $e
28.0000 +—-—~
+
| PERFORMANCE TEMPORARY PARAMETERS
| Bulk
2860S IF +
+
30 00.00 +.
————-----—-- +
1 USER TONE PARAMETERS
1 Bulk
W277F +
——+
BB OO 00 pence
ence eee +
| USER DRUM SET PARAMETERS
1 Butk
39 204 F tema
<GS (Model [D=42H) >
Address (1)
Block
10000
+
-
—+
| SYSTEM PARAMETERS
1 Individual
4001 3F
+
aaa
ao
401x 00
+--—-—----
—-----
{ PART
PARAMETERS
| individual
1 (x= 0-F}
'
402x 5A +
a
woag:
Al m0 00 +——-—-——_—__-_-----
+
| DRUM SETUP PARAMETERS
1 Individual
1 {m= 0-4)
i
41 mB 7F +
ae
o—
+
AB OOO)
me nt
| SYSTEM PARAMETERS
| Bulk
48.01 10 +
— nnn
ent
| PART PARAMETERS
1 Bulk
48 1D OF +.
rrr
49 m0 00 +-—---——_—.
| DRUM SETUP PARAMETERS
1 Bulk
( (m=0-1)
i
49 mE 17 +
seventeen
There are two ways in which GS data is transmitted: Individual Parameter Transmission in which individ-
ual parameters are transmitted one by one, and Bulk Dump Transmission in which a large amount of data is
transmitted at once.
Advertisement
Table of Contents
