Table of Contents
Advertisement
Chapter 12. Appendix
@ Individual Porameters
Individual Parameter Transmission transmits dala {or requests data) Jor one parameter as one exclusive message {one packet of "FO
. . . . . F7").
In Individual Parameter Transmission, you must use the Address and Size listed in the following "Parameter Address Map". Addresses marked at "# cannot be used as starting addresses.
<GS (Model 1D=42H) >
@ System Parameters
Parameters related to the system of the device are called System Parameters
Address(H)
Size{H)
DatatH)
ameter
Description
Default Value (H)
Description
400000
00.0004
O18 - OVER
MASTER TUNE
100.6
- 100.0 foent}
06.04 00:00
O {cent}
40 00 018
Use nibblized data.
40 00 024
A 00 O38
* Refer to section 4. Supplementary maicrial, "About tuning"(Page 91).
400004
000001
10 -7F
MASTER VOLUME
0-127
TF
127
{= FO 7F 7F 04.01 00 wy F7 )
400005
O00081
28-58
MASTER KEY-SHIFT
-24 - +24 [semitones]
40
Olsemitones}
400006
000001
01-7F
MASTER PAN
-63 (LEFT)
- +63 (RIGHT)
40
0} (CENTER)
40007F
000001
oO
MODE SET
00 ~ GS Reset
(Rx. only}
127 = Exit GS
* Refer to "System exclusive messages related to Mode settings {Page 81).
400110
60:00:10
00- 1BH
VOICE RESERVE
Part 10(Drum Part)
2
2
4001 114
Part}
06
6
4001 12e
Part 2
42
2
4001 134
Part 3
a2
2
400) 14e
Partd
02
2
A001 158
Part 5
02
2
40 01 168
Part &
02
2
4001 178
Part7
02
2
4001 18H
Fart 8
02
2
40 01 198
Part?
02
2
a0 OT LAW
Part 1?
00
0
4001
#
40 01 LF8
Part 16
00
0
* The sum trtal of voices in the voice reserve function must be equat to or less than the number of the maximum polyphony. The maximum polyphony of the XP-30 is 28, For compatibility with other
GS madels, it is recommended thal the maximum polyphony
be equal or Jess than 28.
4001 30
o0ne01
1-07
REVERB MACRO
00: Room 1
4
Hail 2
01: Room 2
02: Room 3
03: Hall 1
04: Hall 2
05; Plate
06: Delay
07: Panning Delay
400131
0000 03
00-07
REVERB CHARACTER
0-7
OF
4
4001 32
00.0001
00-07
REVERB PRE-LPF
0-7
90
0
400133
00001
00 - 7F
REVERB LEVEL
Q- 127
40
4
0134
on 0001
00-7F
REVERB TIME
0-127
40
64
400135
oo 0001
00 - 7F
REVERB DELAY FEEDBACK
0-127
™
0
4001 36
000001
00-7F
REVERB SEND LEVEL TO CHORUS 0-127
0
0
* REVERB MACRO is a macro parameter that allows global setting of reverb parameters. When you select the reverb type with REVERB MACRO, each reverh parameter will be set to the most suit-
able value.
* REVERB CHARACTER
is a parameter that changes the reverb algorithm, The value of REVERB CHARACTER corresponds fo (he REVERB MACRO of the same number.
4001 38
000001
00-07
CHORUS MACRO
00: Chorus 1
ir
Chorus 3
01: Chorus 2
02: Chorus 3
03: Chorus 4
(04: Feedback Chorus
05: Flanger
06: Short Delay
07: Short Delay (FB)
400139
00.00 01
00-07
CHORUS PRE-LPF
0-7
tue
0
4001 3A
00.0001
00 -7F
CHORUS LEVEL
0-127
wv
64
40 01 3B
00.00 0f
00 -7F
CHORUS FEEDBACK
0-127
18
B
MOT IC
00 00 MT
00-7F
CHORUS DELAY
0-127
SD
80
4001 3D
600001
00 -7F
CHORUS RATE
0-127
03
3
4001 3E
000001
00-7F
CHORUS
DEPTH
0-127
iB
19
4001 3F
00000)
0-7F
CHORUS
SEND
LEVEL
TO) REVERB
0 - 127
oO
0
* CHORUS
MACRO
is a macro parameter that allows global setting of chorus parameters. When you use CHORUS MACRO to select the chorus type, cach chorus parameter will be set to the most
suitable value.
85
Advertisement
Table of Contents
