Related Manuals for ZKTeco FaceKiosk-H10A
Summary of Contents for ZKTeco FaceKiosk-H10A
- Page 1 Quick Start Guide FaceKiosk-H10A Version: 1.0 Due to regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between the actual product and the written information in this manual.
- Page 2 1. Components Microphone Speaker Bottom 10.1-inch Touch Screen Binocular Camera Status Indicator Card Reading Area 241.87mm Status LED Description: Front Green-The meeting room is available. Red-The meeting room is occupied. Status Indicator Φ5mm 26.8mm 182mm 30mm 28mm Rear Side Exit Button Power In Ethernet BUT SEN GND COM NO NC...
-
Page 3: Installation Procedure
2. Installation Procedure Preparation before Installation Prepare the necessary tools. Large Cross Network Cable Marker Pen Small Cross Knife Screwdriver Screwdriver Tape Measure Power Strip 6mm Expansion Level Ruler 6mm Impact Rubber Plugs Drill and Screws Unpacking and Device Testing: Take out the power adapter, power cable and device from the packing from the box one at a time. -
Page 4: Installation
Turn on the device and make sure that the touch and other functions work properly. Knock on the wall to see whether the load-bearing wall is stable. Installation No reserved wiring hole position: Choose the Installation Location: Use a measuring tape to measure the installation height of the device (it is recommended that the bottom of the device be 1.4m above the ground), and use a marker to mark the installation position of the device. - Page 5 Mark the installation position of the rear hanging plate and the outlet position of the network cable and power cable in parallel using a level ruler (the distance between the device edge and the rear hanging plate fixing hole, the green mark in the figure is the rear hanging plate fixing hole and the outlet position of the network cable and power cable, unit: mm).
- Page 6 Align the rear hanging plate with the wall and the installation holes and attach the rear hanging plate with four tapping screws. Pull the network cable and power cable out of the rear hanging board from the cable outlet and connect them into the device. Then align the device to the wall hanging holes with the hooks on the rear hanging plate and hang it on the rear hanging plate.
- Page 7 Reserved wiring hole position: Align the outlet hole of the rear hanging plate with the reserved outlet hole of the wall, use the level ruler to make sure that the rear hanging plate parallel to the ground, and use a marker to mark the position of the fixing holes of the rear hanging plate on the wall.
-
Page 8: Home Screen
4. Home Screen The device has two theme styles for the home page. It can be set in [Meeting Management] > [Meeting Theme]. The default is technology style. Technology Style Business Style... - Page 9 Click the button in the upper right corner to access the main menu. Note: If the Super Administrator is not registered for the device, then tap to access the main menu. If the device has a Super Administrator, then his/her verification is required to access the main menu.
- Page 11 Wi-Fi Connection Tap on [Communication Setting] > [Wifi Setting], and enable the Wireless Network. 6. Armatura One Connection Settings on Device Tap on [Communication Setting] > [Cloud Server Setting]to set the server details. Server Type: Select ZKBiosecurity. Domain Name Server: When the software is in HTTPS mode, the setting should be enabled. Server Address: In domain name mode, you need to type the complete server address and server port, as shown in the figure above.
- Page 12 Settings on Armatura One Open the Armatura One software then select [FaceKiosk Module] > [FaceKiosk Device] > [Device] > [Search] > [Search] > [Add] to add the device to the software. Step 1 Step 2 Step 2 Step 3 Step 4 Step 5 Click [Office Module] >...
- Page 13 In Office Module, click [Reservation Facilities] > [Reserve], click the meeting room to be reserved, fill relevant information, and select participant. Step 1 Step 2 Step 3 Step 4 7. ZKBioTime Connection Settings on Device Tap on [Communication Setting] > [Cloud Server Setting]to set the server details. Server Type: Select ZKBioTime.
- Page 14 Settings on ZKBioTime After setting on the device, the device will be automatically added to the software. Open the ZKBioTime software then select [Device Module] > [Device] > [Device], click the device in the list, modify the Device Name and Area. Step 1 Step 2 Step 4...
- Page 15 In meeting module, click [Meeting] > [Meeting] > [Add], fill the meeting information, select the Meeting Room, Attendee and Check In/Out Settings to complete the meeting reservation. Step 1 Step 3 Step 2 Step 4 When the meeting status is approved, the meeting can be distributed to the device.
- Page 16 Participants can check-in on the home page when the meeting is starting. It is restricted that only the participants or administrators of the current meeting can pass the verification. The verification mode supports face or card. Note: For more details, please refer to FaceKiosk-H10A User Manual.
- Page 17 Copyright © 2023 ZKTECO CO., LTD. All Rights Reserved.