Advertisement
Quick Links
www.norix.com ● TEL 800 234-4900
Assembly Notes:
Norix is not responsible for any damage due to improper installation. If your shipment does not match the parts list, please contact Norix Customer Service at 800-234-4900.
Norix reserves the right to modify design specifications at any time without an obligation to owners of previously sold products.
___________________________________________________________________________________________________________________________________________________________________________________________________
Important Note: For a successful installation, careful and accurate
layout of the anchor brackets is a must. Read through the
instructions first and familiarize yourself with all of the steps. If you
have any questions, please call Norix Customer Care before
proceeding. Norix is not responsible for damage to components
due to improper installation.
Security Caulk is highly recommended to help seal gaps and
secure the furniture in place. Apply caulk to clean surfaces.
Anchor hardware: Please familiarize yourself with the anchoring components as shown below.
If any components are missing, contact Norix Customer Care before proceeding.
Floor Anchor Bracket (2)
011-083
Drill Guide, Pin (1)
011-063
Concrete Anchor,
5/16" X 2" L (4)
024-024
OR
3/8" X 2-1/4" L (4)
024-025
Rev. A - 12/22/23
091-1038
Arcadian Nightstand
Assembly Instructions
Model Number
ARC250
Anchor Tab, Straight (2)
011-059
5/8" Drill Bit (1)
029-944
Guide Tube (2)
029-941
Patents Pending
Low RPM Variable Speed Drill
5/16" or 3/8" masonry drill bit
Pin-in-Torx® Driver Bit T-40 (provided)
Anchor Hook, Left (1)
011-067
Screw, 5/16-18 X 5/8" L, BH (2)
Shim (4)
060-197
Pin in Torx Brill Bit
071-002
Tools Needed
Hammer Drill
5/8" Drill Bit (provided)
Anchor Hook, Right (1)
011-068
021-118
Anchoring Screw (2)
021-212
Page 1 of 9
Advertisement
Related Manuals for norix ARC250
Summary of Contents for norix ARC250
- Page 1 Assembly Notes: Norix is not responsible for any damage due to improper installation. If your shipment does not match the parts list, please contact Norix Customer Service at 800-234-4900. Norix reserves the right to modify design specifications at any time without an obligation to owners of previously sold products.
- Page 2 The procedure for a corner installation is different from a mid-wall installation. These will be shown separately. See page 6 for corner Installation. Nightstand Mid-wall installation: Note: In a mid-wall installation, the Left and Right Anchor open areas Hooks will not be used. Both Ball Lock Pins and Guide Tubes will be used.
- Page 3 6. Carefully measure 3" inward from the first line Make new lines 3" and mark a second line. Repeat on the other side. 3'' inward 7. Place Floor Anchor Bracket with holes centered on centerline as shown, and vertical face aligned with the line as shown.
- Page 4 10. Install Anchor Tabs on the Nightstand Install (2) Straight Anchor Tabs where shown, using (2) 5/16" Screws. 5/16" X 5/8" L Screw Straight Anchor Tab Ensure that the hook on the Anchor Tab is properly nested inside the hole molded into the Nightstand. 11.
- Page 5 12. Set Nightstand in Place Turn the Nightstand upright and position in place over the Floor Brackets. Slide the Nightstand to engage the Anchor Tabs with the Floor Brackets. 13. Install Bed Anchoring Screws Secure (2) 4" long Anchoring Screws through the Guide Tubes from step 11 into the threaded portion of the Floor Anchor Brackets from step 8.
-
Page 6: Corner Installation
Corner Installation: 1. Marking the Location Place the Nightstand on the floor in an upright position in the corner location where it is to be installed. 2. Mark a line on the floor along the exposed side of the Nightstand, toward the center. 3. - Page 7 7. On the side that will be exposed, carefully measure 3" inward from the first line and mark a second line. 3" Exposed end: 3" 8. Place the Floor Anchor Bracket so that the holes are centered on the centerline as shown, and the vertical face is aligned with the inward line as shown.
- Page 8 10. Install Floor Anchors and Brackets If floor anchors other than the provided Concrete Wedge Anchors are to be used, consult the manufacturer for proper installation. If the provided Concrete Wedge Anchors are to be used, drill (4) 5/16" dia. holes a minimum of 1" deep into the floor at the locations where previously marked.
- Page 9 13. Install Guide Tube Insert the Guide Tube into the drilled hole in the exposed side of the Nightstand during step 11. Guide Tube 14. Set Nightstand in Place Place the upright Nightstand over the brackets and slide the Nightstand in place at an angle, ensuring that the Hook Tab engages the Floor Anchor Bracket first.