Advertisement
Quick Links
www.norix.com ● TEL 800 234-4900
Assembly Notes:
Norix is not responsible for any damage due to improper installation. If your shipment does not match the parts list, please contact Norix Customer Service at 800-234-4900.
Norix reserves the right to modify design specifications at any time without an obligation to owners of previously sold products.
___________________________________________________________________________________________________________________________________________________________________________________________________
Important Note: For a successful installation, careful and accurate
layout of the anchor brackets is a must. Read through the
instructions first and familiarize yourself with all of the steps. If you
have any questions, please call Norix Customer Care before
proceeding. Norix is not responsible for damage to components
due to improper installation.
Security Caulk is highly recommended to help seal gaps and
secure the furniture in place. Apply caulk to clean surfaces.
Anchor hardware: Please familiarize yourself with the anchoring components as shown below.
If any components are missing, contact Norix Customer Care before proceeding.
Floor Anchor Bracket (2)
011-058
Drill Guide, Pin (1)
011-063
Concrete Anchor,
5/16" X 2" L (4)
024-024
Rev. B - 10/30/20
091-994
Prodigy Open Chest
Assembly Instructions
Model Number
PRD700
Anchor Tab, Straight (2)
011-059
5/8" Drill Bit (1)
029-944
Guide Tube (2)
029-941
Patents Pending
Low RPM Variable Speed Drill
Pin-in-Torx® Driver Bit T-40 (provided)
Anchor Hook, Left (1)
011-067
Screw, 5/16-18 X 5/8" L, BH (2)
Shim (4)
060-197
Pin Extractor Tool (1)
011-066
Tools Needed
Hammer Drill
5/16" masonry drill bit
5/8" Drill Bit (provided)
Anchor Hook, Right (1)
011-068
021-118
Ball Lock Pin (2)
002-027
Page 1 of 9
Advertisement
Related Manuals for norix Prodigy PRD700
Summary of Contents for norix Prodigy PRD700
- Page 1 Assembly Notes: Norix is not responsible for any damage due to improper installation. If your shipment does not match the parts list, please contact Norix Customer Service at 800-234-4900. Norix reserves the right to modify design specifications at any time without an obligation to owners of previously sold products.
- Page 2 The procedure for a corner installation is different from a mid-wall installation. These will be shown separately. See page 6 for corner Installation. Open Chest Mid-wall installation: Note: In a mid-wall installation, the Left and Right Anchor open areas Hooks will not be used. Both Ball Lock Pins and Guide Tubes will be used.
- Page 3 6. Carefully measure 3" inward from the first line Make new lines and mark a second line. Repeat on the other side. 3'' inward 3" 7. Place Floor Anchor Bracket with holes centered on centerline as shown, and vertical face aligned with the line as shown.
- Page 4 10. Install Anchor Tabs on the Open Chest Install (2) Straight Anchor Tabs where shown, using (2) 5/16" Screws. 5/16" X 5/8" L Screw Straight Anchor Tab 11. Install Guide Tube Insert the Guide Tubes into the drilled hole on each side.
- Page 5 12. Set Open Chest in Place Turn the Open Chest upright WALL and position in place over the Floor Brackets. Slide the Chest to engage the Anchor Tabs with the Floor Brackets. Floor Bracket Anchor Tab WALL Tab engaged under Floor Bracket 13.
- Page 6 Corner Installation: 1. Marking the Location Place the Open Chest on the floor in an upright position in the corner location where it is to be installed. 2. Mark a line on the floor along the exposed side of the Chest, toward the center. Molded line on Chest 3.
- Page 7 7. On the side that will be exposed, carefully measure 3" inward from the first line and mark a second line. On the corner side, measure 4-3/4" from the wall and draw a second line. " Corner end, 4-3/4" 3" Exposed end: 3"...
- Page 8 10. Install Floor Anchors and Brackets If floor anchors other than the provided Concrete Wedge Anchors are to be used, consult the manufacturer for proper installation. If the provided Concrete Wedge Anchors are to be used, drill (4) 5/16" dia. holes a minimum of 1" deep into the floor at the locations where previously marked.
- Page 9 13. Install Guide Tube Insert the Guide Tube into the drilled hole in the side. Guide Tube 14. Set Chest in Place Place the upright Chest over the brackets and slide the Chest in place at an angle, ensuring that the Hook Tab engages the Floor Anchor Bracket first.